Question about 1999 Chrysler 300M

1 Answer

Change Rod bearings

Pouring attitives in oil for knock

Posted by on

Ad

1 Answer

Additives ONLY TAKE YOUR MONEY

Won't do a thing

Did you check bulletins for Chrysler Motors

They have lots of problems

It is 15 years old or or more-SO

Motor has to come out,I wouldn't keep it
or fix it

Posted on Dec 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad oil pump knock


ionMr. Hugo. what to what you do have is the viscosity of your engine oil. Most probably is either long mileage used engine oil and due to that oil mud built up inside the engine, in the oil pan and most likely close to the oil pressure pump filter reducing the suction and that is why you do have cold lifter knocking,as the engine oil that time is thicker and when it gets hot become thinner and lifters stopped knocking. My persona advise do flush the old engine oil using ( RESTORE MOTOR CLEANER ) pour it into the engine old oil,start the engine in idle and few times reving it for 40 minutes. Then drain it and renew the engine oil with new and recommended engine oil for your engine,by renewing the oil filter as well. Also in the new engine oil put also (RESTORE FRICTION REDUCER ) additive and run the engine.For next oil change please do it every 5000 km ( 3000 miles)

Apr 04, 2014 | 2002 Hyundai Santa Fe

1 Answer

Oil poured from botton as well as housing unit.


housing unit? are you refering to the engine block? If oil comes out as fast as you pour it in, check your drain plug in the oilpan, holes in your oil pan. Did you run over something recently?

Usually engines hold their oil unless you've run over a big rock and knocked a hole in the oil pan.

drain plug has fallen out more than likely.

Dec 09, 2013 | 1999 Volkswagen Jetta

4 Answers

Engine knocks at cold startup. knocks more under load. lasts about 5 minutes till warm. Dealer said: 1. " They all do that. 2. Piston Slap, don't worry. 3. Valve train slow to warm up in this...


I bought my wife a Lex and she also experienced the SAME problem. It is TRUE that that's one of the engine's characteristc's,but it can be corrected. These are the step's that i took.

(1) First step is to change the oil and filter if you HAVE NOT done so lately. (Get a GOOD filter(Fram or Puralator) and oil ( I use ONLY Castrol).

(2) Get a 12oz bottle of Sea Foam(insist on ONLY Sea Foam,because auto part's store's will try to sell you what's on sale. I KNOW that Sea Foam work's). Pour HALF of the bottle in your oil and the other half in the gas tank(Make sure that you have atleast a half of a tank of gas BEFORE you pour in the Sea Foam). The Sea foam will clean your engine internally to promote better oil flow,especially at cold start up when ou need it the most. When added to gas it act's as an upper engine cleaner to get rid of carbon build up in your Intake and EGR Valve which can cause the symtom's that you describe.

(3) Protect your internal engine part's during cold start wam up's by pouring in a bottle of Slick 50 AFTER you do the recommended oil change.

(4) Lastly, use NOTHING but 93 octane gas in you vehicle.

If you do ALL of these step's, you should notice the difference.

Feb 13, 2011 | 2007 Lexus ES 350

1 Answer

How to replace the knock sensor on a 2004 chevrolet silverado 5.3


Hi, the Knock sensor is located on the lower side of the engine near the oil pan rail and goes into water. Make sure your engine is cool before you start the job. The best way is to drain all of the coolant out of the engine first, then disconnect the wire, then remove the knock sensor. WARNING--antifreeze will come pouring out when you take the knock sensor our so WEAR SAFETY GOGGLES to protect your eyes. Do not use any sealer other that the sealer that is on the new sensor.
Take care

Aug 03, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Lifter stuck& knocking in top of motor


Pour in some engine cleaner and run for 4-5 min, this should free up the lifter. Drain the oil and install new filter and oil. You may have to do this 2-3 times over the next month just to clean all the gunk out.

Mar 24, 2010 | 2002 Oldsmobile Silhouette

2 Answers

Where are the knock sensors located on a 02 chevy


It is usually below the the cylinder head on the passenger side towards the back of the engine. It has a white single mushroom shaped connector.

Jan 30, 2010 | 2002 Chevrolet Tahoe

2 Answers

Noise Top end of V6 Saab Engine


hey i dont know if u already solved ur problem but i was having the same problem with mine so i went and bought this solution called risoline, compresion repair. when i changed my oil i poured that stuff in first and then the oil. with in a day it stoped the clicking/knocking noise. hope this helps

May 18, 2009 | 1996 Saab 9000

1 Answer

2002 impreza RS Major oil leak


If you heard a loud knocking.....I'm sorry to say, I'd hope for the worst. It doesn't sound good that you lost that much oil.

But try to clean it with a steamer or with some brake clean. Put a little oil back in and see where it is coming from. If it runs out without starting the car.....then you have definitely cracked the block, or the oil pan.

Dec 04, 2008 | 2002 Subaru Impreza

3 Answers

Knocking under valve cover on cold starts


Is there any smoke when you first start it? what is happening is the valve seals are probably worn and letting the oil seep past them. when your engine is first started it has no oil or very little oil at the top of the engine, thus causing the knocking noise. could be more but this is a most likely answer. oh and is you haven't changed your oil every 3,000 miles you had beeter start doing it.... answer knocking sounds usually come from bottom of engine try a better quality and correct viscosity oil

Nov 17, 2008 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
1999 Chrysler 300M Logo

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...