Question about 1995 Toyota Land Cruiser

1 Answer

Noise when shifting gears..whats the problem?

I've check the clutch assembly but I cannot find.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,585 Answers

When you shift you put pressure on the throw out bearing. This is your noise. Replace it. You should replace the clutch package at the same time. Have the flywheel resurfaced. You olny want to do this one time.

Posted on Dec 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 Pontiac Bonneville GXP will not shift into 4th gear I was to it was a fourth gear band but is that the only problem that will cause itI'notto shift into 4th gear


Which transmission does yours have 4T65-E or 4T80-E ?

4T80-E
No Fourth Gear

Checks

Causes

1-2 Shift Solenoid Valve
?€¢
Inoperative
?€¢
Debris
?€¢
Pinched wires

3-4 Shift Valve Bore Plug

Misassembled

4th Band

Burned, slipping, missing

4th Servo Cover

Cracked

4th Servo Pin

Broken, seized

4th Servo Piston

Damaged

4th Servo Seals

Rolled, cut or damaged
4T65-E
Slipping or No Fourth Gear
Slipping or No Fourth Gear Checks
Cause

DEFINITION: A large engine RPM increase is noted in fourth gear, Drive range, with little or no vehicle forward speed increase. First, second, and third gear operation are normal. Shifts into fourth gear are soft or do not occur. Fourth gear ratio is 0.705:1.

Automatic Transmission Fluid Level
Low fluid level

Transmission Main Line Pressure
Low transmission main line pressure

Oil Filter Assembly
• The oil filter assembly (100) is missing, plugged, or damaged.
• The oil filter seal assembly (101) is missing or is damaged.

Control Valve Body Assembly
• The 3-4 shift valve (362) or the 4-3 manual downshift valve (360) is stuck or binding.
• Debris is found in the passages of the control valve body (301) or of the control valve body spacer plate and gasket assembly (396)

Case Cover Assembly
Distortion or damage occurs at the manual valve (404) or at the case cover (401), causing PRN oil leak.

Driven Sprocket Support Assembly
A plugged third clutch oil passage in the driven sprocket support assembly (609)

Fourth Clutch Assembly
• The clutch plates (500-502) are worn, damaged, or misassembled.
• A missing or not seated fourth clutch spring retaining ring (601)
• A damaged spring assembly (602) or piston (603)
• Worn or damaged fourth clutch piston seals (604, 605)

Third Clutch Sprag Assembly
• The sprag (720) was misassembled or backwards on the inner race (661).
• A damaged third clutch sprag assembly (653, 661, 719-721)

Dec 06, 2015 | Pontiac Cars & Trucks

1 Answer

I have a 2005 Saturn Vue, lately I've noticed my gear shift is super hard to shift into 1st & so on. Is it the cold weather, and if so, is there something i can do to make it manageabl


check clutch hydrolics to make sure fluid is not low. Try double clutching. When in neutral, push clutch in, then out and in again and try shifting into low.

Jan 07, 2015 | 2005 Saturn VUE

1 Answer

Grinding clutch


I'm a little confused on your description of the noise. If I understand you correctly It is making the noise when it shifts smoothly into gear but at the same time it makes a grinding noise ? It possibly can be synchronizers if the grooves on the inside of the synchronizers are worn bad enough to where the gear isn't slowing down enough causing a grind as the clutching teeth on the gear mesh with the synchrode and the shift collar.
If it is making noise in all gears except 4th you may have countershaft brgs failing. The power flow in 4th gear goes directly through the mainshaft and has a 1 to 1 ratio. All other gears the powerflow goes through the countershaft causing a load on the countershaft so if you have bearings failing in the countershaft you will hear noise in all gears but 4th.
i hope I understood you correctly .

Jan 18, 2014 | 2002 Subaru Forester

1 Answer

Torque coverter clutch circuit malfunction on mercedes benz 2003 c230 kompressor


For car not changing gears it can be shifter assembly issue,or it can also be transmission issue.Get the shifter assembly inspected with ignition OFF.For more troubleshooting, i suggest you to get the Following help link checked,its complete step by step procedure to inspect gear shift issues:-----

GEAR SHIFT ISSUES
http://alltypesofpartsreplacing.blogspot.com/2012/11/gear-shift-issues.html
==========
These will help.Thanks.

Nov 29, 2012 | Cars & Trucks

1 Answer

Standard transmission wont shift into 1st gear


Hi Eric, If by standard shift you're talking about a manual transmission, check the clutch fluid first. Open the hood (bonnet) and on the fire wall at the back of the engine compartment you will see two reservoirs. One is for the brakes and the other for the clutch. Open the smaller of the two and check the fluid level. If it is empty as I suspect, it means that either the master or slave cylinder is leaking which will mean replacing the defective unit. The other reason could be a defective clutch assembly. To repair the clutch assembly means removing the gearbox and that is a fairly big job. The first job is not very major, but the second is. If you do not like dirty hands it would be better to have a shop do the work, but if you would like to try I'll be here to help. Let me know. Regards John

Sep 22, 2012 | 1999 Hyundai Accent

1 Answer

My 1999 Chevy Silverado 1500 Z71 makes a clunking noise and feels like it got rear ended if I drive it for an hour or so non stop. It seems to be when it shifts from 1st to 2nd gear. I had the ******...


No one can tell you what it is.This is the operating characteristic of your transmission and customer do object to the noise or clunk and dealer discourage the repair. This is TSB 03-07-29-004G. Let me give you a partial copy. INFORMATION
Bulletin No.: 03-07-29-004G
Date: December 15, 2010
Subject: Manual Transmission Operating Characteristics
Cold Operation
Manual transmission operation will be affected by temperature because the transmission fluid will be thicker when cold. The thicker fluid will increase the amount of force needed to shift the transmission when cold. The likelihood of gear clash will also increase due to the greater time needed for the synchronizer assembly to perform its function. Therefore when the transmission is cold, or before it has reached operating temperature, quick, hard shifts should be avoided to prevent damage to the transmission.
Backlash
Backlash noise is created when changing engine or driveline loading. This can occur when accelerating from a stop, coming to a stop, or applying and releasing the throttle (loading and unloading the driveline). This will vary based on vehicle type, build variations, driver input, vehicle loading, etc. and is created from the necessary clearance between all of the mating gears in the transmission, axle(s) and transfer case (if equipped).
Shift Effort
Shift effort will vary among different style transmissions and synchronizer designs. Usually the more heavy duty the transmission, the higher the shift effort because of the increased mass of the components. Shift effort can also be higher in cold weather because the fluid will be thicker. Medium duty transmissions will not shift as quickly as a Corvette transmission. To reduce shift effort, do not attempt to rush the shift - allow the synchronizers to work as designed. Shifting harder will only increase the chance of rushing past the synchronizer leading to grinding while shifting.
Non-Synchronized Gears
Some light duty truck transmissions in 1st gear (creeper-gear) and reverse gears in various transmissions, along with all gears in some medium duty transmissions, may be non-synchronized. This means there is not a mechanism to match input and output shaft speeds to allow for a smooth shift. This function is left up to the driver. This can be noticed if a shift into 1st or reverse is attempted while the vehicle is rolling or before the input shaft stops rotating leading to a gear grind. The grinding can be reduced by coming to a complete stop and pausing for a moment before shifting into the 1st or reverse gear. Some slight grinding can be expected. In medium duty non-synchronized transmissions, the driver must match input shaft (engine) speed to output shaft (driveshaft) speed with every shift. This can be accomplished by double clutching, or by using other methods. If the driver is not able to perform this function properly, there will be gear grinding with each improperly completed shift. Driver training may be required to correct this condition. Clutch brakes are used in medium duty non-synchronized transmissions to allow a shift into gear at a stop. The clutch brake is used to stop the input shaft from spinning, allowing a shift into gear at a stop without grinding. The clutch brake is activated by pressing the clutch pedal all the way to the floor. When the clutch brake is used, it is possible to have a blocked shift with the vehicle stationary. If this occurs, engage the clutch slightly to rotate the input gear to allow the shift. The clutch brake is intended to only be used while at a stop. Care must be taken to not activate the clutch brake while shifting between gears. This could lead to excessive grinding or a blocked or missed shift.

Aug 29, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Hello, I was just changing gears and the clutch was still working but the gears stopped engaging. Any ideas what could be wrong?


There are three parts to a standard shift transmission's clutch assembly. Clutch disk, Pressure plate, and release bearing. If any of these fail there is a loud noise. Since you haven't heard anything disturbing, I think these parts are OK. If everything was running fine until the moment the gears stopped engaging the problem may lie in the transmission itself. If I understand correctly the gears are grinding instead of going into the next gear. Have the transmission checked out to see if it is low on oil or damaged. A mechanic will drain the oil and check for pieces of metal.

Mar 12, 2011 | 2006 Peugeot 604

1 Answer

1998 Ford Taurus SE, Problem Transmissions wont Shift, Took it to the Shop and they Said it Had to be a Electracal Problem?? But they did not Know what, Some times Works Fine Other Times Check Engine Comes...


TRY THIS I BET IT'S YOUR PROBLEM

Neutral Safety Switch
  • Put the selector in the park position.
  • Loosen the screws on the neutral safety switch.
  • Remove the switch.
  • Reverse the procedures to complete the installation.
Clutch Start Switch
CAUTION
Before replacing the clutch switch or any component connected to the vehicle's control computer, disconnect the negative cable from the battery.
  • After replacing the switch, slowly work the clutch pedal and note any unusual noises or interferences with pedal movement.
  • If the switch is adjustable, make sure the clutch pedal height and push rod (free) play are correct.
  • Then check the release point of the clutch.
  • Begin by engaging the parking brake and installing wheel chocks.
  • Start the engine and allow it to idle.
  • Without depressing the clutch pedal, slowly shift the shift lever into reverse until the gears contact.
  • Gradually depress the clutch pedal and measure the stroke distance from the point the gear noise stops (this is the release point) up to the full stroke end position.
  • If the distance is not within specifications, check the pedal height, push rod play, and pedal free play.
  • If the distance is correct, check the clearance between the switch and the pedal assembly when the clutch is fully depressed.
f_mt_tps9.26.jpg Clutch switch to pedal assembly clearance. Courtesy of Toyota Motor Company.
  • Loosen the switch and adjust its position to provide for the specified clearance.

May 22, 2010 | 1998 Ford Taurus

2 Answers

Loud clanking noise in gear if the clutch is not engaged


That is what happens when you try to shift gear with out depressing the clutch pedal while changing gears.

May 06, 2009 | 2004 Kia Rio

4 Answers

Transmission shifting proublem M5R1 1997 FORD RANGER


internal slave cylinders are known to leak , unfortunate it is behind clutch assembly , i would change both , clutch master and slave cylinder

Feb 27, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
1995 Toyota Land Cruiser Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...