Question about 2004 Infiniti M45

1 Answer

How do I remove the plastic clips attaching the divider between the trunk space and the rear seat back? I think that I have to remove this "partition" to access the forward facing ends of the trunk

I have received the struts and am ready to install. I am a novice so even the smallest obstacle is a challenge . Is this task hard?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Infiniti Master
  • 14,585 Answers

Round clips pullout. But they have to by pried out. Once you get them out a bit with a screw driver, use needle nose pliers and grab the shaft of them and twist them out the rest of the way. Be prepared to buy some though, as they do break.

Posted on Dec 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trunk access from back seat


Some vehicles have drop down rear seat, should be a button or pull strap to release. Others do not have the option, and would require removal of the lower seat and seat back by removing bolts.

Mar 24, 2014 | Ford Taurus Cars & Trucks

1 Answer

Does 2003 buick lasabre have access panel for skis in middle of rear seat


In the trunk of the car there is a black panel behind the rear seat remove screws that hold this panel on. There are three magnets at the top of the panel. Remove panel and put screws in safe place. Go back to the inside of the vehicle there are three brackets that hold in top cover of back seat remove that lay it down in the back seat. You now have complete access from the rear seat to the trunk. To reassemble reattach rear seat top. Reassemble black panel in trunk just attach to metal with magnets and then put screws back in. Hope this is helpful and informative.

Aug 05, 2012 | 2003 Buick LeSabre

1 Answer

How to change the third break light bulb in a 2007 hyundai sonata ?


From 2006 to 2010, the Sonata's 3rd brake lamp requires the rear package deck be removed to access that bulb.
1. Remove the rear passenger seat bottom (remove two12mm bolts between the seat back and the seat bottom - tilt the seat back forward to locate these bolts).
a. Press the two bottom front edge tabs to release the front of the seat bottom from the floor.
b. Remove seat bottom & set aside w/two 12mm bolts
c. Tilt both seat backs downward
2. Remove the left & right hand shoulder cushions (12 mm bolt at the bottom of each cushion)
a. Remove seat belt from shoulder cushion guide at the top of the cushion
b. Lift up and forward on shoulder cushions to remove them (if equipped with side airbags, disconnect wire harness connector).
c. Set shoulder cushions aside w/two 12mm bolts
3. Using a small flathead screwdriver, pop out the 'SRS' button cover from the C pillar panels on the left & right hand side to access either the phillips head screws, 10mm bolts, or #30 Torque Screws
a. Remove screws and set aside
b. Using a standard flathead screwdriver, pop out the C pillar panels on both sides (clips hold these panels in place)
c. Set these panels aside after removal w/screws/bolts
4. Trunk Access-way panels are held in place by phillips head screws (two at the bottom (left and right hand sides) and 4 to 5 at the top .
a. Remove left and right hand panels and set aside w/screws.
5. Rear package deck held in place with two plastic clips (white, yellow or pink)
a. lie on your back inside the trunk (trunk lid open to allow for more light). Looking through access hole find 3rd brake light wire harness connector & disconnect.
b. locate package deck clips, one on the left and another on the right on the underside of the pckage deck
c. Squeeze clips to push them out - package deck will come loose
d. Remove package deck & remove 3rd brake lamp bulb socket (turn counter clockwise to remove). Replace bulb & reassemble in reverse order.

Sep 05, 2011 | Hyundai Sonata Cars & Trucks

5 Answers

My son just received a 1995 Ford Taurus GL, the trunk release lever by driver side seat is locked, we do not have a key and now cannot open the trunk. Any suggestions?


I don't know about your 1995 Ford Taurus, BUT I found that when the rear driver side seat was loosened, there were several cables running alongside the driverside rear (underneath the seat and connecting bolt). Pull gently on the cables...you will find one of them is the trunk release cable(which pops oopen the trunk). And lo....there were my keys inside the trunk. Took 5 minutes to take apart and put together. Good Luck.

Jun 07, 2011 | 1995 Ford Taurus

1 Answer

1999 Chrysler Concorde LXI Rear Speaker replacement


If you mean the rear shelf removal, then you begin by removing the rear seat (lift to release the corner clips on each side holding the cushion to the floor). Then remove the fasteners for the seat belts, then lift the seat back to raise and release it from its clips, and remove it from the vehicle. There are then a lower and upper trim panel around the back shelf that you need to remove (these may be on each side of the shelf, e.g. they are called 'quarter trim' panels). Then you will see some push-pin fasteners that hold the shelf across the front lower edge, so you gently pry out the center push-pin of each one of those to release the fastener. Then you pull the shelf forward to release it from the clips that hold it under the window. Then remove the wire to the center high-mounted brake light. The panel with its speakers attached can then be removed, but also remove the wires from the speakers so you don't break those. connections.
That is the procedure as shown in my '98 manual.

Mar 31, 2010 | 1999 Chrysler Concorde

3 Answers

Access for replacing brake light bulbs: Is it from the trunk or under the rear bumper?


you can access the bulbs from the trunk, remove the covering from the inner back of the rear.

Feb 18, 2010 | 1988 Buick LeSabre

2 Answers

I need to replace the rear struts and spings on my 01 sable, Where are the top nuts to loosen for the struts


The bolts are located under the rear deck (where the rear speakers are located) inside the car. First start by opening the fold down rear seats. There you will find 4 bolts holding the rear seat back. Remove them. Pull the seat back forward and lay it down on the rear seat. Next remove the rear deck. There are 2 plastic push-in clips that hold the rear deck. They located toward the front. Pull them out. Now the rear deck can be removed by sliding forward towards the front of the car. Under the rear deck is insulation which can be lifted out. Under the insulation are the bolts for each strut. Remove these bolts and the strut can be pulled out.

Aug 14, 2009 | 2001 Mercury Sable

2 Answers

Beetle convirtible trunk won't open.


I was looking for a solution but found none.  Here is what happened.  I opened my trunk and wound up pulling on a little red plug that will open the trunk.  The red plug pulled loose in my hand.  The cord on the red plug snapped in half.  What I did not know was that there was a small plastic clip that had pulled loose.  The clip connected the various releases (remote, door switch, and inside the trunk handle) to the actual latch.  

Here is what I did.  First I removed the back seat and the frame to the hole that goes back to the trunk (this is a convertible).  The bottom of the seat pulled up and had a rod connected to the car.  I pulled the rod out of the hole and slipped the other side off.  Next I removed the head rests off (they popped up and off).  I used an hex wrench (I think 8mm).  There were three bolts on the bottom of the seat back.  The seat back then comes out.  The frame has 4 or 5 more hex bolts.  Now the hard part.  I was able to reach in and remove a screw under the handle release.  Then I pulled out the plastic inside cover to the trunk, enough to reach a small rod that extended up from the trunk latch.  This released the trunk, allowing me to repair everything.  I replaced the plastic plug cord with a metal cable (this time wrapped around the metal arm of the trunk release).  I put the little plastic connector back on (it did not break, just popped loose).  Now everything works great again.  
Good luck!

Jul 15, 2009 | 2004 Volkswagen New Beetle Convertible

1 Answer

How to remove interior back dash on 2006 hyundai sonata


The shop manual does not illustrate the procedure for removing the rear package deck (back dash). This will be a lengthy description for removing this deck
1. Remove the rear seat bottom (2 12mm bolts located in between the seams at the seat back and the seat bottom (lower the seat backs and you'll have to feel for them). Remove them
2. Remove the seat bottom (two spring loaded clips at the front of the seat bottom).
3. Remove the 12 mm bolts at the bottom of both LH & RH shoulder cushions. Lift UP and then forward (careful you don't break the should cushion clips at the back of the cushions).
4. Using a small screwdriver, remove the SRS caps at the C-Pillar moldings (behind them are either two phillips head screws or 10mm bolts) - remove them
5. Remove the C-Pillar moldings -- they are 'Clipped' into position (use a flashlight to locate them and a long shaft plane screwdriver to help 'unclip' them).

ff32eaf.jpg lower the seat backs down. Note the trunk accessway side moldings (approximately 8 to 10 phillips head screws) remove them and the accessway moldings (you can'r remove the deck unless you remove these accessway moldings).
6. Find the plastic clips which hold the rear deck in place (usually yellow or blue)


0fbe0c6.jpg Remove the rear package deck.
Now, depending on what you want to do now... it's up to you.
Reassembly is in reverse order.

Jun 19, 2009 | 2006 Hyundai Sonata

1 Answer

Were is the fuel pump located?


The fuel pump IS located in the fuel tank. It is easily accessed in this particuar model, under the rear seat. If you have an arm reat in the middle of the rear seat, you'll need to go in through the trunk. Remove the cover from the the far back, between the back of the rear seat and the trunk space. Remove approximately 4 to 6 screws in the center piece of cardboard that attaches the armrest and rearseat to the cross menber of seperating trunk from seat.
From the back seat, grab the top of the back rest of rear seat, PULL HARD forward on left and right sides . This should disconnect the top. Then, on left + right-sides, toward the lower cushon, there will be a bolt, remove them.
Then pull up the bottom cushion.
In the middle of the floor you have left, where the bottom cushion once was, you will find the top of the fuel pump access. From the top there is a cable that goes toward the driverside, follow it to the connector which should be cover by a small piece of foam. Remember to diconnect the pump before attempting to service or replace it.

May 09, 2009 | 1992 Nissan Maxima

Not finding what you are looking for?
2004 Infiniti M45 Logo

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...