Question about Cars & Trucks

Open Question

Blower+fan+on+falcon+fg+not+working changing the fan and checked the fuse

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: fan blower stopped working

I had the same problem and Ia m working to resolve it.
You need to remove the blover under the glove box it's very easy to remove. 1) remove the glove box, 2) the metalic suport that it's hold by 4 screws and finally remove the 3 screws that holds the blower. Take it off and remove the coverplate of the motor ( 2 screws) and
check the brushes. In my case they were worn out. So you need to buy a new motor with the blower aprox $50 or try to replace the brushes.

Posted on Jan 19, 2009

cj2176
  • 520 Answers

SOURCE: 2005 Pontiac Bonneville hvac blower does not come on

Start by checking the blower resistor. It should be under the dash on the passenger side near the blower itself. You will need to remove the glove box to access it. It is a small plate that has only a few screws and a group of wires that go to a plug in the center. Unplug it and remove the screws. When you pull it out it should look like a series of small spring shaped coils. Most likely one or two of them will be burned up. Replace it in reverse order and your blower should start working again. If this is not the problem then test the fan motor itself. Hope this helps. Good luck.

Posted on Jul 26, 2009

honeymokey
  • 3113 Answers

SOURCE: Ac/Heat doesn't work when I turn it on....

Blower motor or resistor.

Posted on Jul 29, 2009

elshaddai159
  • 1016 Answers

SOURCE: removing the steering off an fg falcon?

Hi,

You actually need special tools to do this which only a Ford dealer would have at the moment.
The airbag system or SRS needs to be disabled before you can remove the steering wheel airbag module.

Sorry mate thats the only option you have.

Thanks

Jason

Posted on Jul 15, 2010

  • 1 Answer

SOURCE: s40 fan blower

where could I find a diagram of this?

Posted on Oct 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of radiator fan fuse or fuse link ? Fan doesn't work.


Both should be a fuse under the hood, or under the dash, if there is a fuse link, it will be along the hot side of the wiring on the fan leading into source of power.

May 22, 2016 | Cars & Trucks

2 Answers

Hi i have changed the head gasket on my vw polo and now it is overheating on every journey the fan doesnt seem to come on any ideas what it could be as i have put new temperature sensors and thermostat and...


Hi Marie.

Test if there is voltage to fan motor with engine hot (use a test light or a Voltmeter). If there is 12VDC to fan motor and motor does not turn, then the fan must be replaced. An alternative way to test the fan would be energizing the motor by connecting it to 12VDC. If fan does not run when motor is energized, then the fan is defective.

If fan does not get power fuse, fan relay, thermostat and wiring must be tested. If you have already replaced thermostat, test the rest.

Check the fan fuse first. Most VW use a 30 Amp fuse located in the fuse plate. Refer to the car owners manual for fuse location. Depending on the year of your Polo there is a Coolant Fan Control Relay on the main relay panel. If the relay is good it must power the fan when the engine is hot. Before going for the relay check that two of the relay's contacts are getting power. If there is no power to the relay and fuse is good it means that there is a wiring problem.

Regards.

Ginko

Aug 19, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

Need to know where the fuse is for the fan by the radiator. I know where the fuse box is at because mercury sable has 2 boxes. Which one contains the fan fuse. My fan is not working and been replaced and...


You have a relay there are 2 speeds low speed and high speed this is controled by a cooling fan module if you changed fan and it does not work then you will need to check the fan module, first the relay its in the engine fuse junction box High speed is marked on the relay C1056 and low marked C1058, here is what you can do go to the high spped relay open thhe cover and expose the relay with key on collapse the relay does the fan come on? if it doesnt replace the fan module if it does you will still have to replace the fan module here is the location is at the radiator on the front (may be under shroud)

Jun 08, 2011 | 2003 Mercury Sable

1 Answer

Fan does not come one when temp raises ..changed sensor


Thanks for choosing FixYa and welcome to the site. Which sensor did you change? Did you check the fan fuse? If the fuse is good, you either have a bad wire in the fan harness or a bad fan.

Apr 10, 2011 | Honda Accord Cars & Trucks

1 Answer

AC blower stopped working; tried changing resistor, but no difference


check power at fan motor, if no power then check relay or fuse for fan motor in fuse box. if there is power to fans, then the problem is in the fan motors.

Sep 14, 2010 | 2005 Hyundai Santa Fe

2 Answers

Cooling fans not working on a buick regal 1992?


First check fuse in engine compartment. Use a test light to check for voltage at the fan connector. If no voltage at fan with engine running and hot, replace fan relay in engine compartment relay box. If there is voltage at fan, but fan doesn't run, replace fan. Any questions, please reply.

Sep 09, 2010 | 1992 Buick Regal

2 Answers

1999 Dodge Caravan Overheating When issue started, thought it was a sticky thermastat. Changed that. Then overheated again and noticed the fans spin speed was slow then it kept poping fuses. Used a code...


Worn out or defective fan (spinning slow) and drawing too much amperage, thus blowing the fuse should be a pretty good indicator if all connections have been inspected and confirmed good and clean. I'd double check voltage to fan is up to spec, and use a clamp on amp-meter to verify amperage draw, and if too high, I'd change it. You should be able to get just motor to replace from parts store, provided all other components of the fan are still in good shape.

Sep 09, 2010 | 1999 Dodge Caravan

2 Answers

Cooling fan not working


 buy manual, see if fan runs with alt power source(jumper wires), check temp sending unit 

Sep 13, 2009 | 1990 Ford Tempo

3 Answers

Radiator fan not working


When you say you changed the fan sensors in the fuse box, did you mean the relay. If not check them they are usually mounted in the engine compartment next to the firewall.

Aug 04, 2009 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...