Question about Isuzu Rodeo

1 Answer

2011 rodeo flasher relay

Where is the indicator relay

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 2,210 Answers

The same unit usually does 4 ways as well. If the 4 ways work, trace the noise. Its probably under the dash or the drivers kick panel.

Posted on Dec 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which wire from indicator switch goes to flasher relay im using a narva 2 pin flasher relay in a 2002 holden rodeo one positive from battery an wht colour would it be from the switch or is it 2 wires


There could be no relay in the vehicle because it doesn't need one. CANbus vehicles tend to use a single module to carry out all the vehicle timing requirements - indicators, hazards, wipers, courtesy lights and so forth.
If the flashers don't work it would be better to repair the system than to rewire and use an outdated method, perhaps introducing further fault codes that might affect the operation of other stuff.

A little used hazard switch is a common cause of flasher failure...

If you really must rewire the system, the (ignition) live, as you say, goes to one side of the flasher unit and the other to the centre contact of the indicator switch though you will need a wiring diagram to identify the colour. There is no single universal colour code though if I was looking at an old British car I would expect to see a dark green wire with a thin black trace line.

A wiring diagram will be useful also for identifying the wiring to the lamps and separating the hazard switch wiring from the circuit. If there are two dashboard tell-tale lights the 2-pin relay will be ok but if there is only one you will need a 3 or 4 pin unit depending on whether electronic or electro-mechanical.

Jun 26, 2016 | Holden Cars & Trucks

1 Answer

Where do I locate the relay/flasher unit in a 2001 diesel Holden Rodeo to replace it?


IF the flasher works at all, it is not the flasher. They blink faster than normal when there is a wiring short.

Nov 08, 2014 | Cars & Trucks

1 Answer

Were is flasher relay located in avalanche


The flasher itself is located in the fuse box. No relay.

May 27, 2014 | 2011 Chevrolet Avalanche

1 Answer

Locating flasher relay on a 2000 isuzu rodeo 4wd


under the hood in fuse box or under the dash on firewall. if not there take the drivers side kick panel off

Aug 17, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

Where is the flasher relay?


On 1992 Isuzu Truck Rodeo the Flasher is located: Front seating area, driver side, under dash, mounted above kick panel.

Hope this helps (remember to ratings this free answer and leave some testimonial comments).

Oct 06, 2011 | 1992 Isuzu Rodeo

1 Answer

Flasher relay


Indicator Flasher The turn signals and the hazard warning flasher switch (13A350) use the same indicator flasher (13350). The indicator flasher is located behind the instrument panel (04320), to the right of the interior fuse junction panel. When activated, the indicator flasher flashes the appropriate turn signal lamps.

Removal
  1. Disconnect the battery ground cable (14301).
  1. Press the indicator flasher tab and slide the indicator flasher from the mounting bracket.
  1. Disconnect the indicator flasher electrical connector from the wiring harness.

Jul 01, 2009 | 1995 Nissan Quest

1 Answer

I want to replace the turn signal relay.


the flasher for the signals is under the dash by drivers right foot, also look at the fuse panel on left end of the dash......

Jun 15, 2009 | 1996 Isuzu Rodeo

1 Answer

Turn signals/ flasher don't work


it's called a flasher relay and is either round and silver or black and square, you can pick it up for a couple of bucks at your local auto parts store. please rate this thanks

Sep 30, 2008 | 1993 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...