Question about Cars & Trucks

1 Answer

Why i cannot get a spark

Chacked camshaft sensor and crankshaft sensor

Posted by on

  • honest right
    honest right Dec 06, 2014

    thanx Bill but it does not have one

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,800 Answers

Check immobiliser for operation.

Posted on Dec 06, 2014

  • honest right
    honest right Dec 06, 2014

    thanx Bill but it doesnt have one

×


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The engin was running, cut out after 3min, give me code 18 and a tri angle


Hi Willem, Code 18 is a Crankshaft position sensor/Camshaft position sensor............ P0018
Crankshaft Position Camshaft Position/Correlation (Bank 2 Sensor A)
Crankshaft Position Sensor car not starting coil spark

Camshaft Position Sensor P0340 Testing and Replacement HD

Apr 30, 2016 | Cars & Trucks

1 Answer

How many camshaft sensors on a 1999 olds aurora


The Ignition Control System consists of the following components:
?€¢
Two crankshaft position sensors (A and B).


?€¢
Crankshaft reluctor ring.


?€¢
Camshaft position sensor.


?€¢
Ignition control module.


?€¢
4 separate ignition coils.


?€¢
Eight spark plug wires and conduit.


?€¢
Eight spark plugs.


?€¢
Knock sensor.


?€¢
Powertrain Control Module (PCM). Camshaft Position (CMP) Sensor
Right hand rear of the engine, near the power steering pump

Oct 01, 2015 | Cars & Trucks

1 Answer

How do replace ignition control module in 1998 K-1500 5.0 liter vortec


This system does not use the ignition module used on the DI systems in the past. The VCM controller now controls the ignition control (IC) and bypass functions.
The crankshaft sensor, located in the front engine cover, is perpendicular to a target wheel attached to the crankshaft. The target wheel is equipped with slots situated 60 degrees apart. As the crankshaft rotates, the target wheel rotates past the crankshaft position sensor. The rising and falling edges created by the slots cause a signal to be sent back to the VCM. This signal occurs three times per crankshaft revolution and is referred to as the 3x signal for V6 applications. The signal occurs four times per crankshaft revolution and is referred to as the 4x signal for V8 applications.
The VCM then utilizes this 3x (V6) or 4x (V8) signal in order to provide the correct spark to the engine by way of the single coil driver module. The single coil driver module is basically an electronic switch that when commanded by the VCM, causes the primary coil voltage to breakdown, energizing the secondary coil and providing a spark via the coil wire to the distributor cap. The distributor consists of the following components:
The system consists of the following components:
?€¢
Vehicle control module (VCM)


?€¢
Distributor


?€¢
Ignition coil driver module


?€¢
Ignition coil


?€¢
Crankshaft position (CKP) sensor


Now which part do you want to replace ?

?€¢
Cap and rotor


?€¢
Camshaft position sensor


?€¢
Gear drive and shaft

The camshaft drives the distributor shaft which rotates providing a spark to the correct cylinder by way of the cap and rotor. The camshaft position (CMP) sensor functions much like the crankshaft sensor previously described but provides only a 1x signal to the VCM. That is, for every 2 rotations of the crankshaft, there is 1 rotation of the camshaft. Note that the camshaft position sensor will not affect driveability. The sole purpose of the camshaft position sensor is to provide the VCM with the necessary information for the misfire diagnostic trouble codes (DTCs).

Sep 06, 2015 | 1998 Chevrolet K1500

1 Answer

No spark or fire to plugs


Sounds like a bad crank position sensor or a bad camshaft position sensor.... If the sensors can't tell the ecm where the position the crankshaft or camshaft is, the ecm won't know when to send a spark. So the ecm won't send any spark.

Apr 23, 2013 | 1998 GMC Sierra

1 Answer

I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?


Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Mar 22, 2012 | 1999 Mitsubishi Eclipse

1 Answer

No spark crank sensor new 2.7


If you have no spark, and you replaced the Crankshaft Position sensor, you may have a faulty Camshaft Position sensor, failed Timing Chain or stretched Timing Chain, or a faulty ECM. Since the Camshaft Position sensor doesn't cost much, I would start with that after checking the Timing.
Also, be sure to check the condition of the Connector going to the Crankshaft Position sensor and Camshaft Position sensor.

Mar 18, 2011 | 2000 Dodge Intrepid

1 Answer

I needto know how to replace a Crankshaft postion sensor A circuit


      • The sensor is mounted in a fixed position in the engine block. The tip of the sensor protrudes into the crankcase at a distance of 0.05 plus or minus 0.02 inch from the crankshaft.
      • A crankshaft adjusting tool may be used to check these rings
      place the tool on the pulley extension surface and rotate the tool around the pulley.
    • If any blade touches the tool, replace the pulley.
  • Inspect the trigger wheel behind the crankshaft pulley and the sensor for damage.
  • If the engine misfires all the time or on acceleration only, test the following components:
    • Engine compression.
    • Spark plugs.
    • Spark plug wires.
    • Ignition coils test for firing voltage with a test spark plug.
    • Crankshaft sensor.
    • Fuel injectors on multiport and sequential fuel injection systems. To remove the crank sensor
  • Disconnect the wiring harness.
  • Unbolt the sensor mounting bolt.
If the crankshaft timing sensor or the camshaft reference sensor is removed, follow this procedure when the sensor is replaced:
  • Thoroughly clean the sensor tip and install a new spacer on the sensor tip. New sensors should be supplied with the spacer installed.
fr_24.15.gifSpacer on crankshaft timing sensor and camshaft position sensor.
  • Install the sensor until the spacer lightly touches the sensor ring, and tighten the sensor mounting bolt 105 in.lb.
hope this was what you needed.....

Jun 03, 2010 | 2000 Saturn Ls 4dr Sedan

1 Answer

Don't strart (no inigtion)


chack camshaft sensor and crankshaft sensor

Oct 14, 2009 | 2000 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...