Question about Cars & Trucks

1 Answer

Is there 1or2 conectors on the rotor Assembly ? Thank you.

Posted by on

Ad

1 Answer

Of a model train ?

Posted on Dec 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace rotor/hub assembly on 08 f150


The rotor/hub assembly can be turned; it's done by a lathe that's placed directly on the rotor while it is still mounted on the vehicle. It is called an On Car Brake Lathe.

If you do replace the entire rotor/hub, I suggest buying OEM parts from Ford. There is a major difference in quality over third party vendor parts sold at your local auto parts store; which warp or wear faster...the OEM part has better lasting sealed wheel bearings too

Feb 22, 2017 | Cars & Trucks

1 Answer

Is there 1or2 conectors on the rotor Assembly ? On the air falcon. Thank you.


You are going to have to give a much better description of your problem. Vehicle? Make/model/year. What's an air falcon?

Dec 05, 2014 | Cars & Trucks

1 Answer

2004 chevy astro van new rear brake pads seem too thick


did you turn the rotors some times there ia ridge on the rotors that needs to be machined down.

Jan 24, 2013 | Cars & Trucks

1 Answer

Removing hub assembly on 2001 dodge grand caravan 3.3L 2wd


Remove the axle nut. Place a punch in the fins of the rotor to lock the hub in place when the punch hits the caliper. Remove the caliper and rotor. Unplug the abs sensor Remove the three bolts holding the hub assembly to the knuckle. Remove the hub assembly from the knuckle. It is vitally important to torque the axle nut to the proper spec. Failure to do this will cause the barring to fail quickly! Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 17, 2012 | Dodge Grand Caravan Cars & Trucks

1 Answer

What do i need to remove a rear rotor off a 1993 cadillac seville


Hello Rodrigo, Thank you for the question - the rotor removal is a simple job on the Seville. I will give you the complete procedure.
Raise and support the vehicle.

Remove the rear tires, unbolt the caliper from the bracket, unbolt the bracket from the spindle and clean and grease all slide plates and slide pins using synthetic caliper grease insuring the new brake pads will slide properly in the clean slide plates, remove old rotors from hub assembly, clean machining oil from braking surfaces of new rotors and install them on the hub assembly, reinstall both brackets on spindles and tighten bolts, using a "c" clamp press the piston back inside both calipers and reinstall both calipers on both brackets and tighten bolts, reinstall tires... torque all lug nuts to 100 ft lbs and place vehicle back on pavement.

DO NOT DRIVE VEHICLE. sit in drivers seat and press the brake pedal to the floor several times until the brake pedal feels secure under your foot you are now ready to drive... happy motoring
9_23_2011_4_36_20_am.jpg

If the rotor is stuck, smack it with a dead blow, or soft faced hammer--- it will free up



9_23_2011_4_41_08_am.jpg

After it is loose, pull it straight off of the wheel studs.

Sep 23, 2011 | 1993 Cadillac Eldorado

1 Answer

Ignition timing doesnt advance on 89 f150 with 5.0 and 4 speed transsmission


to star lest look for a timing by pass plug in your wire harness, follow wire from distribuitor, some are located only a few inches form distribuitor conector some all the way to inner fender on drivers side, is this litlle conector is not missing then your distributor advance weigths are stuck, remove distribuitor cap and rotor and try to free them also check if springs are ok, if you found this to complicated buy a rebuilt unit, good luck

Jan 09, 2011 | 1989 Ford F 150

1 Answer

How do you tear down front hub on 4 wleel drive truck?


FRONT DRIVE AXLE Manual Locking Hubs DISASSEMBLY AND ASSEMBLY Fig. 1: Three screws retain the cap to the hub body 91197g48.gif
Fig. 2: Remove the lockring seated in the groove of the brake rotor assembly 91197g49.gif
Fig. 3: Remove the hub body assembly from the brake rotor assembly 91197g50.gif
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the three screws retaining the cap and remove the cap from the hub.
  4. Remove the lockring seated in the groove of the brake rotor assembly.
  5. Remove the hub body assembly from the brake rotor assembly. To install:
  6. The installation is the reverse of the removal.
prev.gif next.gif

Oct 12, 2010 | 1997 Ford F250 SuperCab

1 Answer

How to i remove rotors off of a 1991crown victoria


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the caliper from the spindle and rotor, but do not disconnect the brake hose. Suspend the caliper inside the fender housing with a length of wire. Do not let the caliper hang by the brake hose.
  4. Remove the grease cap from the hub and remove the cotter pin, nut retainer and adjusting nut.
  5. Grasp the hub/rotor assembly and pull it out far enough to loosen the washer and outer wheel bearing. Push the hub/rotor assembly back onto the spindle and remove the washer and outer wheel bearing.
  6. Remove the hub/rotor assembly from the spindle.
  7. Inspect the rotor for scoring and wear. Replace or machine as necessary. If machining, observe the minimum thickness specification.

  1. If the rotor is being replaced, remove the protective coating from the new rotor with brake cleaner. Pack a new set of bearings with high-temperature wheel bearing grease and install the inner roller bearing in the inner cup. Pack grease lightly between the lips of a new seal and install the seal, using a seal installer.
  2. If the original rotor is being installed, make sure the grease in the hub is clean and adequate, the inner bearing and grease seal are lubricated and in good condition, and the rotor braking surfaces are clean.
  3. Install the hub/rotor assembly on the spindle. Keep the assembly centered on the spindle to prevent damage to the grease seal or spindle threads.
  4. Install the outer wheel bearing, washer and adjusting nut. Adjust the wheel bearings according to the procedure in , then install the nut retainer, cotter pin and grease cap.

Nov 08, 2009 | 1991 Ford LTD Crown Victoria

1 Answer

How to replace 99 gmc 3/4 tom brake rotors


Removal & Installation
  1. Remove 2/3of the brake fluid from the master cylinder.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Remove the front wheel hub extension (dual wheel vehicles only).
    • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
    • Mark the relationship of the front wheel hub extension to the hub
    • Remove the front wheel hub extension bolts
    • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
  5. Mark the relationship of the rotor to the hub.
  6. Remove the caliper and mounting bracket as an assembly.
  7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
  8. Remove the rotor.
  9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
    • Clean all the surface areas and the threaded holes of contamination
    • Generously apply penetrating oil or the equivalent to the hub/rotor area
    • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
    • Tighten both bolts evenly to force the rotor from the hub.
c3692a2.gif
To install:
  1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
    NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

  2. Install the rotor.
  3. Install the caliper and the mounting bracket as an assembly.
  4. Install the tire and wheel assembly.
  5. Remove the safety stands.
  6. Lower the vehicle.

Oct 25, 2009 | 1999 GMC Sierra

1 Answer

Rear rotor on 2004 f250 will not come off


trere is a parking brake drum assembly attached to the rotor.you need to back off the parking brake shoes.

Sep 22, 2009 | 2004 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...