Question about Cars & Trucks

1 Answer

At low speeds my jeep sometimes stumbles - Cars & Trucks

Posted by on

Ad

1 Answer

And what does the data tell you?

What has been tested so far & the results?

Ever do any Preventive Maintenance or only
break down?

Posted on Dec 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep stumbles or stalls when you come to stop


Could be a speed sensor or Throttle position sensor. Depending on the age of your jeep, you should be able to get an inexpensive code reader that will connect to the computer and tell you what is wrong. You can also get great support at Allpar Dodge Chrysler Plymouth Jeep and related cars minivans and trucks . This user supported website has excellent forums on repairs for all kinds of Jeeps and Chrysler products.

Jan 27, 2016 | Jeep Cars & Trucks

1 Answer

I have a timing problem. Low idle speed that is intermitten and causes a stumble at starts. This problem also occurres during normal running RPM's. Missing electronic signal but intermitten?


Could be bad sensor whether crank sensor, sam sensor, idle air control sensor, bad ignition module, bad coil or even timing belt. if you have a service engine soon light/creck engine light it's more than likely a sensor. If no light, probably timing belt/fuel filter plugged/ or weak fuel pump.

Jan 17, 2013 | 1995 Toyota Camry

1 Answer

Fuel problems


I wouldn't replace the injectors, especially not all 6 or 8.
The problem is probably a lack of fuel or fuel pressure, or a dirty throttle body.
The computer controls idle speed with the idle air control valve by limiting the amount of air entering the throttle body. If the body is dirty the air passages can be blocked.
I would take another look at the throttle body and check the fuel pressure.

Aug 25, 2012 | Jeep Cherokee Cars & Trucks

2 Answers

Engine stumbles, hesitates, at low speeds


does it seem to sputter or hesitate when you excellerate through a turn?

Nov 24, 2011 | 2000 Subaru Outback

1 Answer

The engine in my 1994 jeep grand cherokee 4.0 idles very low (below 400 r.p.m's) when it sits still, Can I idle it up....how??


The idle speed adjustment on most fuel injected vehicles is located in a recessed hole near the throttle butterfly on the intake manifold(sometimes with a plug in it). Screwing out the adjusting screw should increase idle speed.

Aug 18, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Just installed a Solex #92808 on my 1952 Willys Jeep truck and it will run at a fast idle but not well and will not run at idle speeds. The needle valve adjusting screw does not make any difference. Could...


Likely you have a vacuum leak somewhere. check by spraying water or carb cleaner on the intake to head parting line and anywhere else there could be a leak. When you hit the leak, the motor will change idle or stumble.

Oct 08, 2009 | Jeep CJ Cars & Trucks

1 Answer

RPM runs low, sometimes just stalls out.1988 4.0 L jeep cherokee


have your TPS looked at cuz it sounds like that may be faulty since it's supposed to control your idle speed

Aug 21, 2009 | 1988 Jeep Cherokee

1 Answer

My 95 grand cherokee sometimes cuts out when tank is low


Check for electronic ingition problem, especifically the ignition module.

Jul 16, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Problem while driving 1987 jeep cherokee


Your engine is stumbling "off idle" - as it switches from idle to throttle control. The idle air motor regulates the air flow and engine speed at idle. If the idle is smooth but the stumble occurs just as the throttle is pressed this isn't the problem, The MAP sensor is mounted in the middle of the firewall behind the engine just below the hood. It has to sense the manifold vacuum drop when the throttle is opened. This my first suspect. Second would be the fuel pressure regulator. If it runs O.K. after you get it going, this is a weak suspect unless it loses power when pulling. A bad fuel pump, again low fuel pressure. Just like the squirt from the accelerator pump in the carburetor days, the injectors have to deliver a good stiff shot of fuel when the throttle opens to keep the engine from stumbling. The MAP sensor will tell the ECM a squirt is needed but the fuel system has to have the pressure to deliver.

Jun 08, 2009 | 1987 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...