Question about Cars & Trucks

1 Answer

How to assemble press fit hub on keyed shaft

Posted by on

Ad

1 Answer

Of What?

Posted on Dec 05, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 scion xa and need to remplace the frnt wheel bearing and have to have it pressed in/out of hub assembly how long of a job it? Or was it easier to purchase the complete hub assembly?


You still have to remove the hub, if you can do this your self take the hub and have new bearings pressed in , check the price of a new hub against the cost of bearings and labour fitting . The job should take around 2 hours.

Dec 03, 2015 | Scion Cars & Trucks

1 Answer

How to place the main bearing shaft support back into Muncie 4 speed transmission


Here's what Chilton has to say on assembling the main shaft.
1.assemble 2nd gear, from rear of main shaft, with hub toward rear.
2.Install 1-2 synchronizer ring , with clutch taper to rear, together with a blocker ring on each side so their keyways line up with the clutch keys. Some units will have a snap ring to go on now or some units will have a 1st gear spacer sleeve to go on.
3. Install 1st gear with hub toward front and 1st gear thrust washer.
4.Press rear main bearing onto shaft being sure to seat it firmly. The diagram shows a piece of 1 and 5/8 ID pipe used to do this.
5. Install correct snap ring in groove on mainshaft behind rear bearing. Max gap between snap ring and rear face of bearing is 0"-.005".
6.Install 3rd gear, hub to front, and synchronizing ring, notches to front.
7. Install 3-4 clutch assembly with taper and hub to front. Make sure keys in hub correspond to notches in 3rd gear synchronizer.
8.Install snap ring on mainshaft with ends of snap ring behind spline teeth.
9.Install rear bearing retainer. Spread snap ring in plate to allow plate to drop around main bearing and press on end of mainshaft until snap ring engages groove on bearing.
10. Install reverse gear with collar to rear.
11. Press speedometer gear drive on mainshaft. From the inside face of the speedometer drive to the inside face of the rear bearing retainer should be 4 and 5/16".

Sep 15, 2013 | Cars & Trucks

1 Answer

2008 Dodge Avenger wheel hub replacement


The front bearing comes as a hub assembly, so you should be able to unbolt it from the spindle. You still have to take the axle shaft out.

Jun 03, 2013 | 2008 Dodge Avenger

1 Answer

Cannot see how the hub is removed. The main nut on the end of the drive shaft has been removed butusing a bearing puller simply pushes the drive shaft back and does not remove the hub


You will need to remove the spindal assembly from the car and press the hub out with a 20 ton or larger press.You can try using a slide hammer puller but this is rarely sucessful.

Feb 20, 2011 | Volkswagen GTI Cars & Trucks

2 Answers

I would like to know if the wheel bearing is in the shaft or the hub?


The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Jun 16, 2010 | 1999 Daewoo Nubira

2 Answers

Can you discribe the proceedure to replace the front wheel bearing on a 94 volvo 850 Thanks Rob


front wheel bearing comes as complete hub assembly remove brake calliper and brake disc remove drive shaft nut at the back of hub housing there are some bolts wire brush this area well use penetrating oil remove the bolts tap hub out of housing can be tight so take your time clean housing well then fit new hub secure bolts fit and tourqe up hub drive shaft nut fit disc and calliper

Oct 22, 2009 | 1994 Volvo 850

1 Answer

Front brake rotor on 1992 Ford Ranger 4wd with auto lock in


With Automatic Locking Hubs
  1. Raise the vehicle and install safety stands.
  2. Remove the wheel lugnuts and the wheel and tire assembly.
  3. Remove the retainer washers from the lugnut studs. Remove the automatic locking hub assembly from the spindle.
  4. Remove the snap ring from the end of the spindle shaft.
  5. Remove the axle shaft spacer
  6. Being careful not to damage the plastic moving cam or thrust spacers, pull cam assembly off the wheel bearing adjusting nut and remove the two plastic thrust spacers from the adjusting nut. CAUTION: Do not pry on the plastic cam or thrust spacers during removal. Prying may damage the cam or spacers.
  7. Using a magnet, remove the locking key. NOTE: If required, rotate the adjusting nut slightly to relieve pressure against the locking key, before the key can be removed. CAUTION: To prevent damage to the spindle threads, look into the spindle keyway under the adjusting nut and remove the separate locking key before removing the adjusting nut.
  8. Loosen the wheel bearing adjusting nut from the spindle using a 2-3/8 inch Hex Locknut Wrench T70T-4252-B or equivalent.
  9. While rotating the hub and rotor assembly, tighten the wheel bearing adjusting nut to 47 Nm (35 ft lb) to seat the bearings. Spin the rotor and back off the nut one-quarter turn (90 degrees).
  10. Retighten the adjusting nut to 1.8 Nm (16 in lb) using a torque wrench.
  11. Align the closest lug in the wheel bearing adjusting nut with the center of the spindle keyway slot. Advance the nut to the next lug if required. Install the separate locking key in the spindle keyway under the adjusting nut. WARNING: Extreme care must be taken when aligning the spindle nut adjustment lug with the center of the spindle keyway slot to prevent damage to the separate locking key. The wheel and tire assembly may come off while the vehicle is in motion if the key is damaged.
  12. Install the two thrust spacers and push or press the cam assembly onto the locknut by lining up the key in the fixed cam with the spindle keyway. CAUTION: Extreme care must be taken when aligning the fixed cam key with the spindle keyway to prevent damage to the fixed cam.
  13. Install the axle shaft spacer.
  14. Clip the snap ring onto the end of the spindle shaft.
  15. Install the automatic locking hub assembly over the spindle by lining up the three hub assembly legs with three pockets in cam assembly. Install the retainer washers.
  16. Install the wheel and tire assembly. Install and tighten lugnuts to 135 Nm (100 ft lb).
  17. Make sure the final end play of the wheel on the spindle is 0.00-0.08 mm (0.000-0.003 inch). the maximum torque to rotate the hub is 2.8 Nm (25 in lb).

Jul 27, 2009 | 1992 Ford Ranger

1 Answer

I have a 1997 Dodge Ram 1500 4 wheel drive. I


i have found that you need to first make sure the cv shaft is moving free in the bearing. soak everything with penitrating oil. you should be able to move shaft in & out a little. the hub is a very tight fit. you need to tap it some from side to side untill you see a little gap between hub and spindel. then place the head of a flat screw driver in that gap and all around the hub, prying back and forth where ever possible. soak, tap and pry all over. be hard on it if replacing, more gentle if not. good luck.

Jul 17, 2009 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

I have a Disco II and the wheel hub bearing went and i'm tryign to change it but i cant seem to get the hub off, can any one help with a step to step guide or something, thanks.


RAVE says the following:
1) Release ABS Sensor harness grommet from inner wing valance and disconnect multi plug.
2) Raise front of vehicle.
3) Remove road wheel.
4) Pull ABS Sensor harness through aperture into wheel arch.
5) Release harness from brackets on inner wing valance, suspension turret and front hub.
6) Release stake from drive shaft nut
7) Remove drive shaft nut with assistance & discard.
8) Remove front brake disk (Remove calliper, pad holder, screw and tap to remove)
9) Remove 4 bolts securing wheel hub to steering knuckle.
10) Release wheel hub from steering knuckle then remove wheel hub and drive shaft assembly from axle. DO NOT REMOVE ABS SENSOR FROM HUB. HUB AND SENSOR ARE SUPPLIED AS AN ASSEMBLY.
11) Position the wheel hub and drive shaft on a press, place supports beneath the wheel studs and press the drive shaft from the wheel hub.
12) Remove drive shaft oil seal from axle casing.

Refit is mostly the reverse, you need to take care to lubricate things in the right places and put loctite on the drive shaft and locate the loom and torque everything right.

Mar 24, 2009 | 1999 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...