Question about Cars & Trucks

1 Answer

How do you change the block heater on a1999 Ford taurus 3 litre curated engine , the block heater is at the back of the motor , between the motor and transmission

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

DOES THE CAR REALLY NEED IT MY CAR DOES NOT HAVE ONE. ONLY DESILES NEED THE BC THEY HAVE GLOW PLUGS TRY RUNNING WITH OUT IT LET THE CAR WARM UP . JUST DISCONNECT THE WIRES SO YOUDONT PWR IT

Posted on Dec 04, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change a block heater in a 1999 Ford taurus se durance 3 litre durance engine


SO you have determined that the installed heater has failed and confirmed that your electrical connections are all good... Then you will need to drain the coolant and then extract the heater from the plug hole before pressing the new heater back into the same spot then refill the coolant. This is an interference fit so make sure you get it seated and check for leaks before considering the job complete. Good luck!

Nov 26, 2014 | Cars & Trucks

1 Answer

How do you change the block heater in a 1999 Ford Taurus S.E. 3 litre 24valve duratec engine


Remove the inoperative heater and install the new one. You just have to gain access to the side of the engine block where the heater is located. Might have to remove something that is blocking access to the heater like the starter or something else.

Nov 14, 2014 | 1999 Ford Taurus

1 Answer

Where is the block heater located on a 1999 Ford Taurus 3 litre 24 valve engine


I have never seen a factory block heater on a Taurus. If you have one, someone put it in. It could be at any of the six ports (three on each side) of the engine (really just four, no one would put it behind an engine mount. Not even Ford). Follow the cord to it. If you can't find the cord(drivers side p by the headlights), most likely you don't have one..

Nov 14, 2014 | 1999 Ford Taurus

2 Answers

Heater core problems no heat changed thermostat still no heat any ideas


try flushing cooling system could be a blocked heater core.if flushing doesnt work remove and replace heatercore.

Nov 26, 2010 | 2002 Ford Taurus

1 Answer

Engine runs but serp belt not moving on a1999 ford taurus


needs a new crank pulley ,the rubber mountinjg has come apart

May 17, 2010 | 1999 Ford Taurus

2 Answers

My 2001 ford taurus is leaking coolant on the firewall side of the engine. is there a coolant hose on that side that could be leaking?


It could be a hose on top of the engine leaking back there. It could also be a freeze plug on the back of the engine. Its a round disk about 2-3" in diameter and is recessed about 3/8" into the block. Check those out and make sure all hoses are good and tight. Any hoses that are kind of puffed out above the clamp should be replaced

Sep 30, 2009 | 2001 Ford Taurus

1 Answer

2002 taurus SEL-5 engine codes to go with light and problems


Cylinders 2, 3 have coil packs change out located on back of motor. you will have to take the upper intake off to get to them. Very easy to do. #2 center plug on back of motor #3 is on drivers side of motor. Crank sensor you will have to remove tire on car passenager side next look at crank pulley on left side of block you will se two wires the heat cover running to it.
Change these first it might correct the O2 sensor problem.

Jun 15, 2009 | 2002 Ford Taurus

1 Answer

Thermostat replacement


Follow your radiator hose all the way to the engine block, it is located at the end of this hoes. you will need to remove this hose to retrieve it. this will be the large hose connected to the radiator. there is a metal couple at the end that couples this hose to the engine block. its in the front of the motor on top of the water pump.

Jan 28, 2009 | 1999 Ford Taurus

1 Answer

Heater stopped working.. blower not working? 1999 ford taurus


sounds like the blower motor resistor which controls blower motor speed has a short and needs replaced.

Jan 25, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...