Question about 2003 Saturn ION

1 Answer

How to put on belthow do i install fab belt 2003 saturn ion cant fin how to move tensioner

How to install fan belt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

The tensioner will have a mounting bolt in the center. Put a wrench (box end) on the bolt to pivot the tensioner. Note - make sure you are moving the tensioner and not trying to move an idler pulley

Posted on Dec 04, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
playon186
  • 45 Answers

SOURCE: Saturn Belt Tensioner...

You probably have a bad tensioner, you cannot tighten a bad tensioner because the bearrings inside have gone bad so your belt will just keep coming off. I had the same problem, don't wait to fix this because your car can over heat, you can lose power steering without proper belt tension. Pay the few dollars now(and I do mean few) and avoid problems later.

Posted on Nov 03, 2008

  • 5 Answers

SOURCE: saturn ion blower motor

lower settings as far as speeds for your blower motor go through a resister block to reduce the voltage your blower motor receives to make it turn slower. If it turns slow on high you would have to check the voltage at the blower motor, should be the same voltage that would be at the battery. There could also be material in the blower motor fan like things a mouse could have put there. Causes the fan to spin slower and also blocks the fins from pushing air. Any strange noises would be heard unless you have had the prob since you owned it and could not detect any changes. It could be even full of stuff and still
be in balance. but it could be a few other things.

Posted on Dec 23, 2008

  • 1596 Answers

SOURCE: where is 2003 saturn ion thermostat?

FACEING the ENGINE It is At TOP RIGHT SIDE Close to Master Cylinder takes About 1 hour to Replace Have Fun its a EASY One
Please Dont forget to RATE ME Thank You

  1. Drain the cooling system.
  2. Remove the bolts that secure the thermostat housing to the water pump feed pipe.
Remove the feed pipe
  1. Remove the thermostat and retaining sleeve, noting the orientation for installation.
Installation Procedure
Install the thermostat and retaining sleeve with the dimple placed into the housing slotImportant: Lubricate the O-ring with soapy water or coolant before installing the O-ring in the water pump.

  1. Install the feed pipe that connects the thermostat housing to the water pump.Notice: Refer to Fastener Notice in Service Precautions.

    1. Install the bolt that secures the water pump feed pipe.
      • Tighten the bolt to 10 Nm (18 inch lbs.) .
    1. Fill the cooling system.

Posted on Feb 09, 2009

blueextc3221
  • 15935 Answers

SOURCE: Oxygen sensor location on a 2003 Saturn Ion-1

One is front of the cat, and one after the cat of the exhaust.
The OBD Scanner should tell you which bank is producing the error.
Bank one is the front one.

Thanks for using FixYa - a FixYa rating is appreciated!!

Posted on Feb 21, 2009

  • 3 Answers

SOURCE: 2003 Saturn Ion will not start. Security lock is on.

The fix for this problem is well known, so is the cause. GM needs to step up in my opinion. You can fix it yourself if you're willing

http://moontaj.com/passlock

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put on belthow do i install fab belt 2003 saturn ion cant fin how to move tensioner


See the arrow ?? Near the 'tail' of said arrow is a 'square' hole in the tensioner....Add tool,rotate25305889-he3vdclfw2d3q24brnzekcbx-3-0.gifin the direction of arrow & remove belt.....New belt installs in reverse order.

Dec 03, 2014 | 2003 Saturn ION

1 Answer

How do I change the alternator in a 2006 saturn ion


Did you loosen the bolt in the center of the tensioner pulley?

Jan 02, 2013 | 2006 Saturn ION

1 Answer

My 2003 saturn ion is over heating i had the thermostat changed and new hoses put on and it still over heats


Could be a Bad radiator Cap? Low Water? Clogged radiator? Not enough air flow, Do To.... Dirty radiator fins? Bad Fan Clutch or Electric fan not running? Timing Off? Stuck closed Thermostat? Bad Water Pump? Blown head Gasket(s)? Cracked Cylinder Head(s), ECT....

Jul 19, 2011 | Saturn Relay Cars & Trucks

1 Answer

On my 2001 sl. i cant seem to get enough slack for belt install. how far should the tensioner move?


The tensioner should move quite abit, make sure your putting your wrench or socket

on the extension of the tensioner, and not where it bolts down, and normally it gives

clockwise or to the right. good luck!

Jun 26, 2011 | 2001 Saturn SL

1 Answer

How do you loosen the tensinor to replace surpintine belt


Use a tensioner pulley kit (or a 1/2" breaker bar if equipped with a 1/2" square hole) to release tension on the belt by rotating the tensioner until tension is released on the belt. properly.

Some tensioners don't have a square hole to put a breaker bar, but must be turned at the pulley's stationary hex bolt.

Good luck on replacing the serpentine belt.

Dec 30, 2010 | 2003 Saturn ION

1 Answer

The Serpentine belt broke on my 2006 Saturn Ion and am trying to replace but cant find the belt diagram?


You don't need a belt diagram. Just thread the belt with the back 'smooth' part to the smooth pulleys, and the 'grooved' part of the belt to the grooved pulleys until the last pulley you have is the tensioner pulley that is turned using a breaker bar in most cases.

Aug 19, 2010 | 2006 Saturn ION

1 Answer

How to replace serpentine belt on 2000 saturn L series not ion


Click on the following direct Link. It has the Serpentine Belt Diagram for the L-Series for your specific engine and options (AC/No AC etc.). It has other additonal diagrams for your future use. It also has diagrams on how to rotate/move the Tensioner Pulley/Arm to loosen and remove the Belt.

Standard Rules to Removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT OR OPENING (3/8ths or 1/2 inch square opening) rotating it\moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.

Standard Rules for Installing the Serpentine Belt:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.

b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2000/make/saturn/model/ls/2000_saturn_ls_drive_belt_routing_diagram.htm

Mar 19, 2010 | 2000 Saturn SL

1 Answer

2003 Saturn Ion died out on the freeway


Sounds like a timing belt,, open the oil cap and look in there with a flash light,,
have someone turn the key if you see nothing moving in there then its the timing belt,,

Mar 12, 2010 | 2003 Saturn ION

1 Answer

Replace serpentine belt on 03 Saturn ion ? how do i release tensioner and where is it located


for the most part there is a tensioer holding the belt on give these websites a try www.alldatadiy.com and www.autozone.com wish you the best of luck Michigan Man.

Mar 08, 2010 | 2003 Saturn ION

1 Answer

ENGINE RUNNING BUT FAN BELT IS NOT MOVING


you will need to replace your fan belt clutch.

Dec 19, 2009 | 2003 Saturn ION

Not finding what you are looking for?
2003 Saturn ION Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...