Question about Cars & Trucks

Open Question

How do you terminate this service? - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ecu not responding in 2002 buick rendezvous. I lost my only key so I bought 2 from a locksmith but he was not able to program the keys. The device he hooked up to my buick said ecu not responding.


unfortunately your only option is the dealer ,
Connect a scan tool to the vehicle.
Turn ON the ignition, with the engine OFF.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info. under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a master passkey III key, turn ON the ignition with the engine OFF.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10-minute relearn procedure.

Jul 08, 2017 | Buick Cars & Trucks

1 Answer

Reset 2007 6.0 Lumina service kilometer display


please follow this steps and fix it. God bless you
  • 1 Open the hood of the Lumina.
  • 2 Locate the negative battery terminal on the battery. This has a black wire and is identified by a negative "-" stamped on the battery housing.
  • 3 Disconnect the negative battery terminal using a box-end wrench and isolate it so it does not come back into contact with the negative battery post.
  • 4 Leave the negative battery terminal disconnected for 10 to 15 minutes.
  • 5 Reconnect the negative battery terminal and recheck the service-engine-soon light by starting the car.

Nov 27, 2013 | Chevrolet Lumina Cars & Trucks

2 Answers

Jumped the battery and immediately the lights came on. However the car would still not start. The car was VERY low on gas so we added at least 2 gallons of gas to it. Car still wont start. It clicks when...


Load test the battery if possible, but more than likely the battery has become unable to hold a good enough charge to start the vehicle. I would also clean the pos. and neg. terminals of all corrosion and make sure they are tight.

Oct 29, 2013 | 2007 Volvo S40 2.4i Sedan

1 Answer

How to replace a starter??


Ford Excursion, Expedition, Lincoln Navigator 2000-2005
Starter

Print


Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.

    Negative battery cable
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE To disconnect the hard-shell connector from the solenoid S terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and S terminal.


    Starter terminal cover Terminal nut and separate the battery starter cable from the starter motor Solenoid S terminal connector, if equipped with a starter mounted solenoid
  4. Remove or disconnect the following:

    Starter motor retaining bolts Starter motor from the vehicle

To install:
  1. Install or connect the following:

    Starter motor and retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). Bttery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). Slenoid S terminal connector, if equipped with a starter mounted solenoid Sarter solenoid safety cap, if equipped
  2. Lower the vehicle.
  3. Remove or disconnect the following:

    Ngative battery cable
  4. Start the engine several times to check starter motor operation.

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:

    Negative battery cable
  3. Raise the front of the truck and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
  4. Remove or disconnect the following:

    Wiring from the starter motor terminals Starter motor retaining bolts, loosen Starter retaining bolts while supporting the starter motor Starter from the vehicle

To install:
  1. The installation is the reverse of removal. Tighten the starter retaining bolts to 15-20 ft. lbs. (20-27 Nm)

4.6L, 5.4L & 6.8L Engines
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Remove or disconnect the following:
    NOTE To disconnect the hard-shell connector from the solenoid S terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and S terminal.


    Starter terminal cover Terminal nut and separate the battery starter cable from the starter motor Solenoid S terminal connector, if equipped with a starter mounted solenoid
  5. Remove or disconnect the following:

    Starter motor retaining bolts Starter motor from the vehicle

To install:
  1. Install or connect the following:

    Starter motor and retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). Battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). Solenoid S terminal connector, if equipped with a starter mounted solenoid Starter solenoid safety cap, if equipped
  2. Lower the vehicle.
  3. Connect the negative battery cable.
  4. Start the engine several times to check starter motor operation.

6.0L Diesel Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the battery ground cable.
  3. Remove starter solenoid protective cap.
  4. Disconnect the starter motor electrical connections.
  5. Remove the bolts and the starter.

To install:
  1. Installation is the reverse of the removal procedure. Tighten the starter bolts to 18 ft. lbs. (25 Nm)

7.3L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:

    Negative battery cable
  3. Raise the front of the truck and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
  4. Remove or disconnect the following:

    Wiring from the starter motor terminals Starter motor retaining bolts, loosen Starter retaining bolts while supporting the starter motor Starter from the vehicle

To install:
  1. The installation is the reverse of removal. Tighten the starter retaining bolts to 15-20 ft. lbs. (20-27 Nm)


Testing & Troubleshooting

Feed Circuit Test

  1. Make sure the battery is fully charged.
  2. Disconnect the Inertia Fuel Shutoff (IFS) switch.
  3. Connect a remote starter switch between the starter solenoid S-terminal and the battery positive (+) terminal.
  4. Connect the Rotunda 73 Digital Multimeter positive lead to the battery positive (+) post. Connect negative lead to the starter solenoid M-terminal.

    0996b43f80204e8b.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Motor feed circuit-S-terminal (1), remote starter switch (2), battery (3), Rotunda 73 digital multimeter (4), B-terminal (5), M-terminal (6)

  5. Engage the remote starter switch. Read and record the voltage. The voltage reading should be 0.5 volt or less.
  6. If the voltage reading is 0.5 volt or less, go to the Motor Ground Circuit Component Test.
  7. If the voltage reading is greater than 0.5 volt, indicating excessive resistance, move the Rotunda 73 Digital Multimeter negative lead to the starter solenoid B-terminal and repeat the test. If the voltage reading at the B-terminal is lower than 0.5 volt, the concern is either in the connections at the starter solenoid or in the solenoid contacts.
  8. Remove the cables from solenoid B-, S- and M-terminals. Clean the cables and connections and reinstall the cables to the correct terminals. Repeat Steps 3 through 6. If the voltage drop reading is still greater than 0.5 volt when checked at the M-terminal or less than 0.5 volt when checked at the B-terminal, the concern is in the solenoid contacts. Install a new starter motor.
  9. If the voltage reading taken at the solenoid B-terminal is still greater than 0.5 volt after cleaning the cables and connections at the solenoid, the concern is either in the positive (+) battery cable connection or in the positive battery cable itself.
  10. By moving the Rotunda 73 Digital Multimeter negative lead toward the battery and checking each mechanical connection point, the excessive voltage drop can be located. When the high reading disappears, the last mechanical point that was checked is the concern. Repair or install a new connection as required.

Ground Circuit Test
A slow cranking condition can be caused by resistance in the ground or return portion of the cranking circuit. Check the voltage drop in the ground circuit as follows:
  1. Disconnect the inertia fuel shutoff switch.
  2. Connect a remote starter switch between the starter solenoid S-terminal and the battery positive (+) terminal.
  3. Connect the Rotunda 73 Digital Multimeter positive lead to the starter motor housing (the connection must be clean and free of rust or grease). Connect the negative lead to the negative (-) battery terminal.

    0996b43f80204e8c.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Motor ground circuit-Rotunda 73 digital multimeter (1), battery (2), S-terminal (3), M-terminal (4), B-terminal (5), remote starter switch (6)

  4. Engage the remote starter switch and crank the engine. Read and record the voltage reading. The reading should be 0.2 volt or less.
  5. If the voltage drop is more than 0.2 volt, clean the negative cable connections at the battery and body connections, and retest.
  6. If the voltage drop is greater than 0.2 volt, determine which way the current is flowing in the cable.
  7. Connect the Rotunda 73 Digital Multimeter positive lead to the end of the cable nearest battery positive.
  8. Connect the multimeter negative lead to the terminal at the other end of the cable.
  9. Crank the engine and observe the voltage reading. The voltage reading should be 0.2 volt or lower. If the voltage drop is too high, clean the terminal ends. Retest, and if still high, install a new cable. If the voltage reading is less than 0.2 volt and the engine still cranks slowly, install a new starter motor.

Voltage Drop Test

WARNING When servicing the starter motor or performing other underhood work in the vicinity of the starter motor, be aware that the heavy gauge battery input lead at the starter solenoid is "electrically hot" at all times.

WARNING A protective cap or boot is provided over the battery input terminal on all vehicle lines and must be installed after servicing. Be sure to disconnect the battery ground cable before servicing the starter motor.
Always make the Rotunda 73 Digital Multimeter connections at the component terminal rather than at the wiring end connector. Making a connection at the wiring end connector could result in false readings because the meter will not pick up a high resistance between the wiring connector and the component.

Aug 05, 2012 | 2001 Ford Expedition

1 Answer

How to change the starter . for olsmovile aurora 1997.


Starter REMOVAL & INSTALLATION 3.5L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove or disconnect the following:
    • Lower front air deflector
    • Starter electrical connectors
    • Torque converter cover
    • Starter bolts and shims
    • Starter Fig. 1: View of the starter - 3.5L engine 9306xg02.gif
    To install:
  4. Install or connect the following:
    • Starter. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Torque converter cover
    • Starter electrical connectors. Torque the positive battery terminal nut to 84 inch lbs. (10 Nm) and the "S" terminal nut to 20 inch lbs. (2 Nm).
    • Lower front air deflector
    • Negative battery cable
  5. Lower the vehicle.
3.8L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove or disconnect the following:
    • Splash shield
    • Flywheel cover
    • Starter electrical connectors
    • Starter Fig. 2: View of the starter - 3.8L engine 9306xg03.gif
    To install:
  4. Install or connect the following:
    • Starter. Torque the bolts to 32 ft. lbs. (43 Nm).
    • Flywheel cover. Torque the bolts to 22 inch lbs. (7 Nm).
    • Starter electrical connectors. Torque the positive battery terminal nut to 12 ft. lbs. (16 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
    • Splash shield
    • Negative battery cable
4.0L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Intake manifold
    • Starter electrical connectors
    • Starter Fig. 3: Exploded view of the starter - 4.0L engine 9306xg04.gif
    To install: WARNING
    Before installing the starter, torque the inner solenoid and battery terminal nuts to 70 inch lbs. (8 Nm). If not properly tightened, the starter may fail due to terminal or cap damage.
  3. Starter. Torque the bolts to 22 ft. lbs. (30 Nm).
  4. Starter electrical connectors. Torque the positive battery terminal nut to 70 inch lbs. (8 Nm) and the "S" terminal nut to 26 inch lbs. (3 Nm).
  5. Intake manifold
  6. Negative battery cable
prev.gif next.gif

Feb 04, 2011 | 1994 Oldsmobile 88

1 Answer

Need a manual to change the starter on a, 1994 Nissan, Quest mini van + 6 cylinders


http://groups.yahoo.com/group/villagerquest/

Section 03-06: Starting System 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

Apr 27, 2010 | 1994 Nissan Quest

1 Answer

Replace starter


96 probe, 2.0L 4 cylinder. Should be similar to 626 I think.

Starter Motor
Removal


Exploded View of the Starter Motor Mounting Components




  1. stu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When servicing the starter motor or performing other underhood work in the vicinity of the starter motor (11002), be aware that the heavy gauge battery input lead at the starter solenoid is "electrically hot" at all times. A protective cap or boot is provided over this terminal (B-terminal) on all carlines and must be replaced after servicing. Be sure to disconnect the battery ground cable before servicing the starter motor.
    Disconnect the battery ground cable (14301).
  1. Remove the air cleaner (ACL) and the air cleaner to intake manifold tube (9B697). Refer to Section 03-12A for the procedures.
  1. Remove the two upper starter motor bolts.




  1. Raise and support the vehicle.
  1. Remove the intake manifold support bolts and the intake manifold support (9J444).




  1. Disconnect the S-terminal wire.
  1. Remove the B-terminal wire nut and disconnect the B-terminal wire.
  1. Remove the lower starter motor bolt.
  1. Remove the starter motor.

Aug 10, 2009 | 1995 Mazda 626

1 Answer

My 95 nissan quest


2 hour job from top driver side of engine.

Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

May 27, 2009 | 1994 Nissan Quest

3 Answers

Engine light 2006 pontiac g6(reset)


first be sure that its the engine light and not the "service" light. the service light will usually illuminate if its time for an oil change. if its the service light ur owners manual should tell u how to reset it. if its ur engine light then try disconnecting ur positive battery cable for 1 minute. that should reset ur ecm and get rid of the engine light. if the engine light comes back on then have a diagnostic scan done to determine whats causing it. LJ

Dec 29, 2008 | 2006 Pontiac G6

2 Answers

Turning of oil service light on OBD II


My recommendation is definitely in the certified sevis because if you make a wrong conection wires can spoil the main computer

Jun 25, 2008 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...