Question about Cars & Trucks

1 Answer

Code P0340.... It says camshaft position sensor A bank one circuit malfunction. I have replaced the cam sensor, spark plugs and change the oil. Code is still showing does anyone know what the problem could be?The cam sensor is getting power so I know that's not the problem. I am guessing the coil packs? Can somebody please help me?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

Replace crankshaft sensor

Posted on Dec 03, 2014

  • Kevin l Dec 03, 2014

    I've already done that. That's not the problem it's been tested and is working

  • Randall Harrell
    Randall Harrell Dec 03, 2014

    what year and model car ? both camshaft and cranksenor are good ?

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 407 Answers

SOURCE: 97 STS CODE P0340 CAMSHAFT POSITION SENSOR CIRCUIT

is the car running bad? you may have jumped time or there is a electric problem in the circuit

Posted on Oct 28, 2009

  • 1206 Answers

SOURCE: I got a camshaft position sensor malfunction code P0340.

it sounds like you have bigger problems if your car does not crank(turn over) then your timing belt could have broken and the one piston could be hitting a valve causing it to be locked up.normally when any sensor is bad car engine still cranks it just doesn't start.

Posted on Jan 28, 2010

emissionwiz
  • 75222 Answers

SOURCE: where is the Camshaft Position Sensor located on a

this car has but one bank, the cam sensor is under the intake manifiold on the drivers side.

Posted on Feb 25, 2010

Testimonial: "thanks, now I know where to start looking. Is it a fairly easy item to replace?"

  • 280 Answers

SOURCE: code reads P0340 Camshaft position Sensor circuit

That makes the computor think the timing is off. Replace the sensor and see if that does it. You will then have to have the code cleared (erased) or the light will come back on/stay on.

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

I changed out the MAP sensor,and the idle air sensor on my 2006 Ford Taurus. This was before I had the fault code read at a dealer. Code came back as P0340, and P0430 Band 2 cat worn out. I had the cam...


P0340 FORD - Camshaft Position Sensor Circuit Bank 1 Sensor 1Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
P0340 FORD Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
P0430, main catalyst is worn out.

Dec 04, 2012 | 2006 Ford Taurus

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

3 Answers

I have a Chevy 2006 Aveo. Two codes came up when the engine check light was put on a scanner. Code P0340 and Code P0133. The check engine light has turned off and on by itself several times in the...


P0340 OBD-II Trouble Code - Camshaft Position Sensor Circuit Malfunction

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
* Hard starting or no start
* Rough running / misfiring
* Loss of engine power

Causes: A code P0340 could mean one or more of the following has happened:
* a wire or connector in the circuit could be grounded/shorted/broken
* the camshaft position sensor may have failed
* the PCM may have failed
* there exists an open circuit
* the crankshaft position sensor may have failed

Possible Solutions: With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Visually inspect all the wiring and connectors in the circuit
* Check for continuity in the circuit wiring
* Check the operation (voltage) of the camshaft position sensor
* Replace the camshaft position sensor as required
* Check the crankshaft position circuit as well
* Replace circuit wiring and/or connectors as required
* Diagnose/replace the PCM as required



P0133 OBD-II Trouble Code - Oxygen Sensor Circuit Slow Response (Bank1, Sensor1)

This involves the front oxygen sensor on Bank 1. This code indicates the engine air fuel ratio is not being adjusted by the oxygen sensor signal or the ECM as expected to do so, or not adjusted as often as expected to do so once the engine is warmed or under normal engine use.

Symptoms: You will likely not notice any drivability problems, although there may be symptoms.

Causes: A code P0133 may mean that one or more of the following has happened:
* The oxygen sensor is faulty
* The wiring to the sensor is broken / frayed
* There is an exhaust leak

Possible Solutions: The simplest thing to do is to reset the code and see if it comes back.
If the code comes back, the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
* Check and fix any exhaust leaks
* Check for wiring problems (shorted, frayed wires)
* Check the frequency and amplitude of the oxygen sensor (advanced)
* Check for a deteriorating / contaminated oxygen sensor, replace if necessary
* Check for inlet air leaks
* Check the MAF sensor for proper operation


Hope this helps (remember to rate this answer).

Feb 09, 2011 | 1999 Chevrolet K1500

2 Answers

I have a diagnostic code 340 and 320 on a 1997 Jeep Cherokee. What might the problem be?


DTC P0340 - Camshaft Position Sensor Circuit Malfunction
Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes:A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

Possible Solutions:With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

DTC P0320 also have with this wrong.

Jul 13, 2010 | 1997 Jeep Grand Cherokee

3 Answers

Where is the Camshaft Position Sensor located on a


this car has but one bank, the cam sensor is under the intake manifiold on the drivers side.

Feb 25, 2010 | 1998 Ford Escort

4 Answers

Trouble codes p0340 and p0014 for a chevy trailblazer engine keeps either idling up real fast or trys to die


You need to check the cam phazer and see if it's damaged. Lots of the time it leaks oil into the connector and messes up the wires. Also I've seen the oil control screens come out of the phazer and go into the engine, which will also set the coeds. If I were you I'd pull the phazer out and see if all 3 of the oil control screens are there. My bet is one will be missing. Make sure to change the oil too. You may get lucky and it will have made it to the oil pan? Other wise I wouldn't worry too much about it. Most of the time it will not cause any engine problems. Good luck, oh and you do have to pull the power steering pump off to get the phazer out. But you can just take the bolts out for the pump and let it fall down so you can get the phazer out!

Nov 26, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

How to fix po134 sensor


O2 Sensor Circuit No Activity Detected Bank 1 Sensor 1

the bank one sensor is either disconnected are faulty.

the bank one sensor is the sensor in the exhaust of the rear cylinder bank of the engine cylinders 1,2,3, the sensor is the one before the catalytic converter. U will need an O2 semnsor socket to remove it or in some cases a 7/8" open end wrench will do.

Oct 23, 2009 | 1996 Plymouth Grand Voyager

1 Answer

Code p0340 need location on 2004 sebring 2.7 v6



P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction


What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

Oct 23, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...