Question about Cars & Trucks

1 Answer

How do I recode my new control module

Recoded to the intructions but door is not locking

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Discunect your battery for 20 sec end check after your start your code is gone

Posted on Dec 03, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is the Honda Acty 1985 ignition key the same one as door key


with new cars it is normal to have the one key code for all the locks on the car
if your ignition key is different to door locks or boot lock it is possible that a new barrel was fitted at some time requiring a new key where the barrel should have been recoded to existing key
it is still possible that a locksmith can re code the barrel to the door lock key reducing the necessity of having many keys

Jul 10, 2016 | Honda Cars & Trucks

1 Answer

My key fob won't lock or unlock doors Has new battery quit all of a sudden


that sounds like the key needs to be recoded most key fobs run on a rolling code system and after a while the codes run out

Jul 03, 2016 | Cars & Trucks

1 Answer

Remote Entry system. Key works in ignition system but will not open the door.


Ok, ill assume your power locks are functional. So chances are your remote either needs a batt., recoded,replaced, and very rarely the ecm takes a powder.

Oct 12, 2014 | 2000 Mercury Sable

2 Answers

2011 ford fiesta air bag sensor location


Which sensor are you looking for? Or are you looking for the control module where all the sensors connect to? The airbag control module (known as the Restraints Control Module (RCM)) is located under your center console (see picture below).

2011-ford-fiesta-air-bag-sensor-location-s3zwbyrgjkpkbjrh2ou4v3xw-2-0.jpg

If the vehicle has been in an accident, you will need to have this module recoded/reset. Ford can do it, or you can mail it off to several sites that will recode it for you (I had it done recently for $45).

Hope this helps!

Oct 14, 2013 | 2011 Ford Fiesta

1 Answer

I need code for radio on my ford


If you haven't got the intruction manual where you would usually find it written in you'll need to either take it to a dealer so there can send it off to have it recoded or find someone local who can recode it for you, Radio Doctor is one I used! you'll save money if youn can get the radio out yourself! Not much else you can do. Did you buy it from a garage? you ould ask them they should of given it to you when you purchased the motor!

Jul 01, 2010 | 2004 Ford Fusion

1 Answer

VW Sharan (2000model) - Recoding Keys


Programming
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Close all windows and doors. Insert key into driver's door lock. Turn key to unlock position 3 times. Remove key.
NOTE: Hold key in unlocked position for 0,5 second.
Programming mode activated (driver's door LED illuminated). Carry out the following within 20 seconds: Point key at infrared receiver. Located near rear view mirror. Press and hold lock button within 5 seconds Fig. 1 [1]. Press unlock button 3 times Fig. 1 [2]. Release lock button Fig. 1 [1]. Correct programming indicated by driver's door LED flashing. Repeat above procedure within 15 seconds to program remaining keys. To exit programming mode and extinguish LED: Wait 15 seconds.
NOTE: A maximum of 4 keys can be programmed.

Feb 04, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

Neither of my keys unlock my car anymore, wondering why this is? it can't be that both batteries in the keys have died.


if its the remote plips you mean, then the car may need recoded to the plips if the car battery has been disconnected or changed recently.

Otherwise the keyblades should still open the doors, or the central locking controller is faulty.

Oct 24, 2009 | 2001 Toyota Celica

1 Answer

I cannot open the doors on my BMW using the remote control or the internal button. I can only open the driver's door using the manual key. The remote control locks the door fine and triggers the alarm....


This is a common fault on the series 3 usually down to the General Module 5 or GMV relays breaking down. Item is situated behind glove box reasonably easy to replace. Cost from BMW about £240.00 Can be found through breakers about £60.00. Keys will have to be recoded. See www.bmwgm5.com for more info.
bmmonks

Jul 21, 2008 | 2003 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...