WHAT IS THE REASON IF COLLING SYSTEM OF BOTH SEATS (DRIVER AS WELL AS PASSENGER SEAT ) , DOES NOT WORK AT ALL? AND HEATING SYSTEM OF FRONT SEATS, ALSO ONLY WOKS IN DRIVER SEAT ALONE NOT

Heated Seat System Operation
The driver and passenger heated seats have 2 heat zone operating modes with 3 heat level modes and will operate only while the engine is running. The heat zones are determined by which of the 2 heated seat buttons are pressed, while the heat level is determined by the number of times they are pressed. Pressing the seat cushion button 1 time will activate the seat back and cushion heater elements in the high mode. Each time the seat cushion button is pressed the seat back and cushion heat level is reduced from high to medium, low, and off. Pressing the heated seat back button 1 time will activate only the seat back heater element in the high mode. Each time the seat back button is pressed the seat back heat level is reduced from high to medium, low, and off. During heated seat operation the heat zone operating mode may be changed without affecting the current heat level mode.
The heated seat switches are momentary contact switches and are inputs to the driver and passenger door modules. Battery voltage is supplied to the switch assembly from the door module, and when a heated seat switch is pressed and released a brief switch signal voltage is supplied to the door module. Whenever the door module receives an active heated seat switch input, the next heated seat operating mode is determined by whatever the current mode may be. The seat heater elements are controlled by the driver seat module using inputs from the door modules through Class 2 serial data circuit messages. The driver seat module controls the voltage supply and the ground circuits to the seat heater elements. When a heated seat function is commanded active, the seat module will switch battery voltage to the heater element supply circuits, and ground is provided through low side drive control circuits. During heated seat operation both the seat back and cushion heater elements are supplied battery voltage. The seat module grounds the appropriate control circuits for back only or back and cushion heating modes, and opens or closes the active control circuits as necessary in order to maintain the desired seat temperature. The seat module relies on inputs from thermistors located in the driver and passenger seat backs to control heated seat temperatures. The thermistors are 2 wire sensors supplied with a 5-volt referenced signal circuit and a low reference circuit from the seat module. Resistance through the thermistors varies with temperature causing the heated seat sensor signal circuit voltage levels to decrease as the seat back temperatures rise. The seat modules allow heated seat operation only while the engine is running which is determined by a Class 2 serial data circuit message from the powertrain control module.

Heated Seat Components
The heated seat system consists of the following components:
• Driver and passenger heated seat switches
• Driver and passenger seat back heater elements
• Driver and passenger seat cushion heater elements
• Driver and passenger seat back temperature sensors
• Driver seat module
• Driver door module
• Passenger door module

Do you know what B - body DTC -diagnostic trouble code are ?
DTC B2425 Driver Seat Heater Circuit
DTC B2435 Driver Seat Back Heater Sensor Circuit
DTC B3941 Front Seat Heaters Circuit

Heated Seat Always On
Step
Action
Yes
No
Schematic Reference: Driver Seat Schematics and Passenger Seat Schematics
Connector End View Reference: Power Seat Connector End Views
1
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Operate the heated seat system.
Does the system operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3
3
Install a scan tool.
Display the Heated Seat Status parameter in the driver seat module Input/Output data list.
Start the engine.
Does the scan tool display the Heated Seat Status parameter as Off?
Go to Step 6
Go to Step 4
4
Display the Heated Seat Mode parameter in the door module Inputs data list.
Does the scan tool display the Heated Seat Mode parameter as OFF?
Go to Step 6
Go to Step 5
5
Turn OFF the ignition.
Disconnect the heated seat switch connector to the door module.
Start the engine.
Does the scan tool display the Heated Seat Mode parameter as OFF?
Go to Step 7
Go to Step 8
6
Replace the driver seat module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Is the repair complete?
Go to Step 9
--
7
Replace the heated seat switch. Refer to Front Seat Heater Switch Replacement .
Is the repair complete?
Go to Step 9
--
8
Replace the door module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Is the repair complete?
Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3


your best bet , have a qualified repair shop diagnose the problem

Heated Seats
This system allows independent seat electrical heating of each front seat on demand.
The components of the system are:

• the seat heater mats located on the seat cushion and backrest.
• the heated seat module located on the passenger power seat track and cushion frame on manual seat track.
• the heated seat switches, located on the electronic automatic temperature control (EATC) module.
• temperature sensors, located in the seat cushion heater mats.

A new heater mat will come assembled on a new foam pad.
Climate Controlled Seats
The climate control seat system is able to heat and cool the front seats. Each climate controlled seat is operated by push-buttons on the electronic automatic temperature control (EATC) module located on the instrument panel. Each front seat temperature is then monitored and controlled by the climate control seat module (CCSM) located on the front passenger seat track.
The climate controlled seat system contains the following components:

• EATC module
• CCSM
• Thermo-electric device (TED) and blower assembly within each front seat cushion and backrest
• Air filter (attached to each TED and blower assembly)
• Cushion TED adapter attached to the cushion frame
• Cushion and backrest manifolds
• Cushion and backrest foam pads
• Cushion and backrest trim covers
• Seats
  Front Seats
  NOTE: The high speed controller area network (HS-CAN) circuits that pass through the passenger seat harness are part of the main HS-CAN LOOP. If the front passenger seat-to-floor connectors are disconnected, a NO START condition will result.
  NOTE: The medium speed controller area network (MS-CAN) circuits that pass through the driver seat harness are part of the main MS-CAN LOOP. If the front driver seat-to-floor connectors are disconnected, various MS-CAN modules will not be able to communicate.
  The front seats can be equipped with the following systems:
  
  • Two-way manual seat track (passenger only)
  • Four-way manual seat track (driver only)
  • Six-way power seat track
  • Manual recline
  • Power recline
  • Backrest, without fold flat
  • Backrest with fold flat (optional, passenger only)
  • Heated seats
  • Heated/cooled climate controlled seats
  • Memory driver seat
  • Manual lumbar (driver only)
  • Power lumbar
  • Adjustable head restraints
  • Seat side air bags (standard)
  • Occupant classification sensor (OCS) system on passenger seat
  
  Driver Seat Module - Memory Seat
  The power driver seat, power outside rear view mirrors and power adjustable pedals are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option. The DSM is located on the driver seat track.
  This system allows automatic positioning of the driver seat to 2 programmable positions.
  
  • A power driver seat position can be stored at any time. The driver must move the seat to the desired position using the driver seat switch assembly. The driver must then depress the memory SET switch which activates the memory SET switch light emitting diode (LED). Within 5 seconds (before the LED goes out), the driver must select a memory position. Memory 1 is selected by depressing memory switch 1. Memory 2 is selected by depressing memory switch 2.
  • If no memory switch input is received within the 5-second time limit, the operation is aborted and the memory seat position switch (set switch) LED is turned OFF. This also occurs if one of the following inputs is received during the 5-second programming limit:
    • Driver seat control switch
    • Memory seat position switch (set switch)
    • Power adjustable pedal switch
  A programmed seat position can only be recalled when the transmission selector is in PARK or NEUTRAL with the ignition switch in the RUN position. A position may be programmed at any time.
• Principles of Operation
  Driver and Passenger Power Seats Without Memory
  The driver and front passenger power seat motors are hardwired to the seat control switches on each respective seat. The circuits are normally at ground through the seat control switch. Each individual seat track, recliner (if equipped) and lumbar (if equipped) motor circuit is switched to power when the specific adjustment position is selected.
  
  Power Driver Seat With Memory
  The driver power seat is controlled by the driver seat module (DSM), if equipped. The memory driver seat feature allows the driver to program a personalized seat position that can be recalled using the memory switch or a remote keyless entry (RKE) transmitter. There are 2 memory settings possible. The outside rear view mirror positions are also stored and recalled with the power driver seat positions.
  The DSM is located underneath the driver seat cushion frame. The DSM does not require calibration to the driver seat track.
  The driver seat control switch provides voltage to the DSM when activated. The NEUTRAL position of each driver seat control switch position is a ground state through the seat control switch contacts. A voltage input causes the DSM to power the appropriate motor until the input is removed. Ground is the normal state of the motor circuits through the DSM and is not switched to control the motors. The DSM internally switches the appropriate circuit from ground to power for operating the motors.
  As the seat is adjusted, the DSM constantly monitors the motor position sensors to record the current seat position. The DSM will remove power from the motor upon termination of the seat control switch input or if the DSM does not see movement from the motor by monitoring the position sensor.
  The DSM communicates diagnostic trouble code (DTC) and other information using the MS-CAN communication bus. It should be noted for diagnostics that because CAN bus communication is more robust and reliable than other methods, it may be possible to have limited module communication with one of the CAN bus circuits disconnected or shorted to ground. Refer to Section 418-00 for information concerning MS-CAN bus communication.

Do you have memory or not ?

Taking the vehicle to a qualified repair shop an having a diagnostic scan of the seat module's done could save time an money , by not replacing parts needlessly .

The heated seats are a luxury feature that heat the front seats. This provides maximum comfort for the driver and the front passenger. To turn on the heated seats, press the heated seat button, which is a picture of a seat. There are two of these buttons, and each are located on the center console. The button on the driver's side of the console controls the heat for the driver's seat, while the button on the passenger's side of the center console controls the heat for the passenger's seat. Pressing the heated seat button will turn the heated-seats onto their highest setting. Pressing the button a second time will lower the heated seats to their medium setting. Pressing the button a third time will result in the lowest setting. Pressing the button a fourth time will turn off the heated seats. There are three lights next to the heated seat buttons to indicate what setting the heated seats are on.
Tip
The heated seats will only work when the engine is running.

Electronic's ! drivers Power seat module , driver door module . Do you know anything about automotive electronic's ?

The heated seat module (MSM) controls heated seat operation for both the driver and passenger seats. There are 2 modes of operation available for heated seats; both the seat cushion and seat back heat, or seat back only heat. When a heated seat temperature signal request is received, the MSM will activate both the seat cushion and seat back heating elements. When the heated seat BACK ONLY mode button is pressed once the MSM will deactivate the seat cushion heating element and leave the seat back heating element ON.
The adjustable pedal system is controlled by the memory seat module (MSM).
your best bet , have a qualified repair shop check it out ! Could have DTC'S - diagnostic trouble codes in door module , BCM etc...

Air Circulation
When the heated/cool seat switch is pressed to initiate operation of the climate control seat (CCS) system, cabin air is drawn through the heated/cool ventilation module air filter, then directed through passages in the foam of the seat cushion and seat back to the seat's occupant. In order for the CCS system to operate to its optimum performance, it is crucial to have unrestricted air flow through the system. A dirty or restricted air filter, the blockage of an exhaust air duct, a misaligned heated/cool ventilation module, or incorrect foam installation of the seat cushion or seat back will all have negative effects on CCS operation.
Heated/Cool Ventilation Module
Each heated/cool seat has 2 ventilation modules, one located under the seat cushion and one located in the seat back. These modules are controlled by the climate control seat module (CCSM). Each ventilation module contains a thermo-electric device (TED), a temperature sensor, and a blower motor. The TED and temperature sensor are mounted downstream of the blower motor. Each TED consists of a circuit of positive and negative connections sandwiched between 2 ceramic plates. Each ceramic plate is equipped with copper fins for heat exchange. The air flowing past these fins is either directed as conditioned air into the seat cushion and seat back, or directed into the cabin as waste air.
A TED is essentially a solid state heat pump that is used to heat or cool the air supply to the seat cushion and seat back. When voltage is applied to a TED, one side releases energy as heat, while the opposite side absorbs energy and gets cold. When the polarity of the current flow to the TEDs is switched, the hot and cool sides of the TED reverse.
During the following climate control seat system description and operation, the TEDs, blower motors, and temperature sensors will be referenced independently even though they are all packaged together as a module.
Climate Control Seat (CCS) System
The CCS system consists of two heated/cool ventilation modules and one climate control seat module (CCSM) that controls both the driver and passenger heated/cool seats systems. The CCSM is mounted below the front passenger seat cushion. It receives power from both, battery positive voltage and ignition 3 voltage.
Once a CCS system is activated, cabin air is drawn through the seat blower motors and directed across the fins of each of the thermo-electric device (TED) located under the seat cushion and in the seat back. The air is either heated or cooled as it passes over the TEDs. This conditioned air is then directed through channels in the foam of the seat pad and through small holes in the seat cover to the occupant. Once the system is activated, the CCSM uses a set of algorithms to control the temperature of the selected heating or cooling modes.
Your best bet is to take your vehicle to a qualified repair shop an have it diagnosed .
DTC B19A4: Driver Seat Back Blower Speed Circuit High

DTC B19A8: Driver Seat Back Blower Speed Circuit Short to Ground

DTC B103D: Driver Blower Power Circuit

DTC B272E: Driver Seat Back Blower Circuit Open
DTC B19A3: Driver Seat Cushion Blower Speed Circuit High

DTC B19A7: Driver Seat Cushion Blower Speed Circuit Short to Ground

DTC B2729: Driver Seat Cushion Over Temperature
DTC B19A2: Passenger Seat Back Blower Speed Circuit High

DTC B19A6: Passenger Seat Back Blower Speed Circuit Short to Ground

DTC B111D: Passenger Blower Power Circuit

DTC B272F: Passenger Seat Back Blower Circuit Open
DTC B19A1: Passenger Seat Cushion Blower Speed Circuit High

DTC B19A5: Passenger Seat Cushion Blower Speed Circuit Short to Ground

DTC B272A: Passenger Seat Cushion Over Temperature
Driver and Passenger Heated/Cool Seats Inoperative

1. Ignition OFF, disconnect the C1 harness connector at the CCSM.
2. Test for less than 5 ohms between the ground circuit terminal M and ground.
?‡'
If greater than the specified range, test the ground circuit for an open/high resistance.

3. Verify that a test lamp illuminates between the B+ circuit terminal E and ground.
?‡'
If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

4. Disconnect the C2 harness connector at the CCSM.
5. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
?‡'
If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

6. If all circuits test normal, replace the CCSM.

Sorry

Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:

• the seat heating elements located in the seat cushion and backrest.
• the heated seat control switch, located on the seat side trim panel.
• temperature sensors located in the seat cushion heating elements.
• heated seat relay.

Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE Test Step Result / Action to Take J1 CHECK HEATED SEAT SWITCH OPERATION

• Key in ON position.
• Press the heated seat switch on the driver and passenger seats.
• Are both heated seat switch indicators illuminated?

Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .

No
GO to J2 . J2 CHECK THE HEATED SEAT RELAY CIRCUITS

• Key in OFF position.
• Disconnect: Heated Seat Relay C3250 (located under the driver seat).
• Key in ON position.
• Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
  
• Are the voltages greater than 10 volts?

Yes
GO to J3 .

No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation. J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT

• Key in OFF position.
• Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
GO to J4 .

No
REPAIR circuit 57 (BK). TEST the system for normal operation. J4 CHECK THE HEATED SEAT RELAY

• Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
  
• Do both heated seat indicators illuminate when pressed?

Yes
INSTALL a new heated seat relay. TEST the system for normal operation.

No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation. J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT

• Key in OFF position.
• Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
• Key in ON position.
• Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
  
• Is the voltage greater than 10 volts?

Yes
GO to J6 .

No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation. J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN

• Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
INSTALL a new heated seat switch. TEST the system for normal operation.

No
REPAIR circuit 57 (BK). TEST the system for normal operation It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do

Mabe is discunect

The following checks and repairs can help you:
1. In the fuse box within the bonnet - check fuse number 22, if burnt, replace it
2. Check fuse 19 in the fuse box inside the car located under the dashboard on the driverside
3. If these steps don't help, the problem may be with the wiring and connection between the module and the seat cushion - inspect it
4. Check if the signal return on the circuit is adequately functioning - if the module is being informed of an active seat
5. If there is a problem - repair or replace the circuit and/or wiring.

yes maybe a fuse, also look under the seat and ensure the wire is connected they sometimes get caught when moving the seat back and forward and split against the metal seat base.

you need to check the resistance in each of the heated seat elements in the seat. There's a two wire connector under the back of each front seat. The connector should be green. disconnect it and measure the resistance along the circuit going into the seat. if it isnt .1 - .3 ohms, replace the appropriate heated seat element