Question about Cars & Trucks

2 Answers

While fitting timing belt to my focas 05 1.4 i think crankshaft moved because with belt on when i turne cranksheft by hand its getting stuck or caught after a little turn

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 107 Answers

Your going to have to index your cams the cam gears have a notch/paint mark on both the gear and the housing behind them I'm not positive on that motor but on the majority of engines the crankshaft must be placed at top dead center of cyl 1 then match the each cam gear to its corresponding markings and the markings on the new belt pay attention when you reapply the belt tensioner as it tends to rotate the cams slightly when tension is applied if this happens you could cause a piston/pistons to contact the valves destroying the piston, bending the valves, or damaging the cam or crankshaft themselves. Good luck I suggest investing in a high quality repair manual before continuing

Posted on Dec 02, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 59 Answers

Were the timing marks lined up correctly when you changed the belt? check.

Posted on Dec 02, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: Crankshaft pulley (vibration damper) moved forward.

the pulley is also a dampener often times they seperate from each other. replace pulley/dampener.

Posted on Nov 18, 2008

mrgreenz
  • 962 Answers

SOURCE: is the crankshaft pulley aright or left handed thread

The bolt in the middle is usually counterclockwise. Standard thread removal.

Posted on Feb 19, 2009

  • 6982 Answers

SOURCE: isuzu rodeo engine seized. how can you check for what is the caus

If engine has seized, the likely cause is that a crankshaft/rod bearing has failed. Unless you ran vehicle low on oil, this can generally be considered to be a material failure. (unless you ran the rpms up way over "redline") Generally the engine can now be regarded as JUNK and just be replaced. You can remove the cylinder head and inspect it to see if it's re-usable, but you should not try to turn it by hand while installed, or you may bend valves.If you decide to re-use it, you will need to completely clean it to remove debris from failure otherwise any junk in passageways can destroy the block bearings in the new one you bolted it to.

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: Changing a timing belt

Did you trying using a pulley puller? You can rent them at some automotive stores

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: crankshaft seal blows out oil leak

The fix is replacement of motor!! I have the same problem and have already paid $700 in repairs to fix seal just to find out that the seal is being knocked out by loose crank shaft..Car had 60000 miles when I bought it 4 months ago, from a dealership, and now it needs a motor replacement..I stiil owe $5000 on a car that is worth $0..Dodge did not give the 100000 mile warranty they love to advertise on TV for the '06 Stratus..They only gave 36000 warranty because they did not think it would last much longer..Will never buy Chrysler product again!! They do not stand behind what they sell or they would have 100000 mile warranty on all their cars..

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While changing my timing belt on my 1.4 focas i think crankshaft moved.because when i turn it by hand its getting stuck or caught


Take the belt off & start over

Put the crank & cam gears where they go

You should have instructions with the new belt
or be working out of a factory quality service manual

Dec 02, 2014 | Cars & Trucks

1 Answer

While replacing timing belt on my 2003 pt cruiser (2.4 liter) I got the belt on with the crank pulley and compression pulley (top front) in timing but exhaust pulley (top rear) off by one tooth. Took belt...


To readjust the cam timing loosen of the valve rockers so that the valves will not move as the cams are turned.. Set the crankshaft on TDC no 1 piston. This will make the mark on the crank sprocket line up with a mark on the housing. The cam shaft marks are to ne facing each other with the "up" marks facing up. Loosen of the adjuster idler and use an allen key to lever the pulley away from the belt. Fit belt and let tensioner off Ensure tensioner spring is in line with the notch. Repeat procedure to get it there.. The valves will now be timed . replace the rockers and adjust as required . The problem that you had is that there was load on the cam lobes from incorrect positioning of the cam shafts and the shaft turns until the load was equal between two lobes.. There is every possibility that there will be bent valves as it is an interference motor.

May 19, 2014 | Cars & Trucks

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

Where are the timing marks for a peugeot 1.9 td 306


Hi

Hope this is helpful, if you need more info get back to me.


1, park car, handbrake on
2, loosen drivers side front wheel bolts,
3, crawl under car use 22mm socket and breaker bar to loosen the crankshaft pulley bolt, it'll probably be quite tight, once undone nip it up again not to tight,
4, open bonnet,
5, jack drivers side of car up, put on axle stand
6, remove wheel
7, loosen and remove intercooler bolts, then intercooler
8, find 6mm allen key
9, behind the starter motor there is a hole in the gearbox housing, put the allen key in it, (may be easier to undo and remove the 3 starter motor bolts)
10, get a 22mm socket put it on the crankshaft pulley bolt, turn the crankshaft bolt clockwise whilst at the same time pushing the allen key into the hole (easier with an assistant but can be done solo) keep turning until the allen key drops into the hole(you'll understand when you do it, may have to turn the engine for quite some time reasonably slowly),
11, thats the engine now on it's timing marks,
12, now put a trolley jack and block of wood under the sump and jack it up until it takes the weight of the engine,
13, remove the left hand side engine mount, basically move the fuel primer to one side, remove the rubber bung if there, then carefully undo the 4 5/8 size bolts and remove the top half of the mount (careful engine doesn't suddenly slip of jack and trap your hand),
14, now remove the 10mm bolts holding the front cambelt cover on, then do the same for the rear cover, except there is one bolt at the back of the cover which is 11mm,
15, now looking at both of the exposed pulleys you will 2 timing holes with a threaded insert behind, on the cam pulley it's at about 4 o clock and i think 2 o clock on the fuel pump, now find the 2 short bolts from the intercooler, they are the right size to fit in the timing holes,
16, now under the arch, remove the crankshaft pulley bolt and pull of the pulley,
17, now remove the lower cambelt cover, all 10mm bolts,
18, now look at the new belt tensioner and you'll see a square hole in it, find the same hole on the car, a short 3/8 socket extension will fit in there and you can then use a ratchet to apply or release the tension,
19, undo but don't remove the two bolts holding the tensioner, now use your ratchet to push the tensioner towards the windowscreen, whilst holding it there use your other hand to release the belt from behind the tensioner,
20, with the belt now loose remove it from round the rest of the components,
21, now replace the waterpump,
22, now replace both the tensioner and idler pulley, to do this you'll need to remove the rest of the metal engine mount, the bolts are quite obvious,
23, replace the belt in the same manner you removed it,
to tension the new belt pull the ratchet towards you then tighten the tensioner bolts at the same time,
24, with the tensioner tightened push the belt in the middle between the two pulleys you should have about half an inch of deflection if correct (check the old belt before removing to give you an idea),
25, now remove the two timing pins in the pulleys and the allen key,
screw the crankshaft pulley bolt into it's hole (leave the pulley off) if you keep screwing it in then the engine will turnover,
26, turn the engine over by hand at least 8 times, then put the timing pins back in as you did at the start, if you've done it all right it'll turn over with no issues
27, recheck the tension again,
28, if alls well then refit the lower cambelt cover,
29, refit the crankshaft pulley,
30, refit everything you've removed, torque all required bolts correctly (except crankshaft pulley which is done last)
31, remove the allen key (2 intercooler bolts will have already been done when fitting the covers and intercooler,
32, turn the engine over again by hand to check there's no rubbing on the cam covers or any other issues,
33, if alls well then top up the engine coolant as you'll have lost alot when doing the waterpump, bleed it properly,
34, put the road wheel back on, lower the car to the ground then torque up the crankshaft pulley bolt,
35, job done start her up then tidy up

Regards

Dan

Dec 29, 2010 | 1991 Peugeot 405

2 Answers

2004 kia rio timing belt replacement procedure


from autozone.com

Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.

25f366d.jpg

b46eac9.jpg

503792b.jpg
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

1.6L (VIN 3) & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Engine cover Right-hand front wheel Right-hand wheel well side cover Accessory drive belts Water pump pulley Timing belt upper cover
  3. Turn the crankshaft pulley so cylinder No. 1 is at Top Dead Center (TDC). Align the pulley groove with the timing mark T of the timing belt cover.
  4. Remove or disconnect the following:
    NOTE If the timing belt is to be reused, mark the belt to indicate its turning direction.


    Crankshaft pulley Crankshaft flange Lower timing belt cover Timing belt tensioner Timing belt

To install:
  1. Align the timing marks of the camshaft and crankshaft sprockets to ensure the No. 1 cylinder is at TDC.
  2. Temporarily install the timing belt tensioner.
  3. Install the timing belt over the crankshaft sprocket, then inside the idler pulley, over the camshaft sprocket and then inside the timing belt tensioner.
  4. Apply tension to the timing belt by turning the tensioner in the clockwise direction so there is no slack in the belt on the tension side.
  5. Tighten the tensioner mounting bolts to 20 ft. lbs. (27 Nm).
  6. Check the timing belt tension as follows:
    1. 1.6L (VIN 3) engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end is approximately 1 / 2 of the tensioner mounting bolt head radius away from the bolt head center.
    2. 2.0L engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end sags approximately 0.16-0.24 inches (4-6 mm).

  7. Turn the crankshaft two turns in the clockwise direction and realign the crankshaft sprocket and camshaft sprocket timing marks.
  8. Install or connect the following:

    Lower timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Crankshaft flange Crankshaft pulley. Tighten bolt to 101-109 ft. lbs. (138-147 Nm) for 1.6L (VIN 3) engine and 123-130 ft. lbs. (168-177 Nm) for 2.0L engine. Upper timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Water pump pulley Accessory drive belts Right-hand wheel well side cover Right-hand front wheel Engine cover Negative battery cable

Sep 06, 2010 | 2004 Kia Rio

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Remove water pump


Disconnect battery earth lead. Do not turn crankshaft or camshaft whn timing beld removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated) Do not turn engine via camshaft or other sprockets. Observe all tightening torques. Remove engine, remve RH engine mounting. Remove auxiliary drive belts, water pump pulley, crankshaft pulley, timing belt upper cover, timing belt lower cover. Turn crankshaft clockwise to TDC on No. 1 cylinder, slacken tensioner bolts 5 & 6. Move tensioner away from belt and lightly tighten bolts. Remove timing belt. Remove water pump and replace with new one. Suggest to replace cambelt as well.
Installation
Ensure timing marks aligned3 & 4. Fit timing belt in anti-clockwise direction, standing at crankshaft sprocket. Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner bolt 5. slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner bolt 6. Tighten tensioner bolt 5. Turn crankshaft on turn clockwise. Ensure crankshaft sprocket timing marks aligned 4.
Slacken tensioner bolt 5. Slacken tensioner bolt 6. Allow tensioner to operate. Tighten tensioner 6. Tighten torque: 20 - 26 Nm. Tighten tensioner bolt 5. tighten torque: 20 - 26 Nm. Apply thumb pressure to belt at middle. Approximately 5kg. Belt should deflect to 1/4 of tensioner bolt head width 7. Belt tention can also be set using burroghs (BT-33-73F) tension gauge 10 at middle. Turn crankshaft 90 ° anti clockwise. Check belt tension is 9.5 16,5kg (engine must be cold). Install components in reverse order of removal. Fit cranckshaft pully. Tighten crankshaft pully bolts 8. G4-J: Tightening torque: 12-15Nm.
G4-N/G4-k: Tightening torque: 10-12Nm
G4EA: Tighten crankshaft pully bolt 9. Tighten torque: 140-150Nm.

Nov 04, 2009 | Hyundai Excel Cars & Trucks

1 Answer

How i fix timing of lantra 1600 cc 95


Disconnect battery earth lead. Do not turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of ratation unless otherwise stated, Support engine. Remove, engine mounting, auxilliaty drive belts. Water pump pulley 1. Crankshaft pulley bolts 21. crankshaft pully 2. timing belt covers 3. Turn crankshaft to TDC on No 1 cyclinder. Ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket and balancer shaft sprocket timing marks aligned. Timing marks on camshaft sprockets should align with cylinder head upper face. Dowel pins on camshaft sprockets should face upwards. Slacken tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove, automatic tensioner unit bolts. Automatic tensioner unit. Timing belt, crankshaft centre bolt, crankshaft sprocket. Crankshaft sprocket guide washer. Slacken blancer shaft belt tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove balancer shaft belt.

Installation
Ensuring timing marks arligned. Note timing marks on camshaft sprockets should align with cylinder head upper face. Exhaust sprocket mark is on recess, but inlet sprocket mark is on tooth. Note: to check oil pump sprocket positioned correctly, removing blanking plug from cylinder block. Insert 8mm diameter Phillips srcrewdriver in hole. Ensure screwdriver is inserted 60mm from face of cylinder block. if screwdriver can only be inserted 20mm: turn oil pump sprocket 360°. Insert screwdriver again. Fit balancer shaft belt in anti-clockwise direction, starting at crankshaft sprocket. Slacken balancer shaft belt tensioner bolt. Turn tensioner clockwise to tension belt. Tighten bolt to 15-22Nm. Apply thumb pressure to belt. Belt should deflect 5-7 mm. If not repeat tensioning procedure. Install crankshaft sprocket guide washer, crnakshaft sprocket. Tighten crankshaft cente bolt. Tighten torque:110-130 Nm. Note ensure crankshaft sprocket guide washer is fitted correclty. Oil treads and contact face of crankshaft body before fitting. Check tensioner body for leakage or damage replace if necessary. Check pushrod protrusion is 12mm. If not replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Resistance should be felt. Place flat washer under tnesioner body to avoid damage to body end plugs. Retain pushrod with suitable pin through hole in tensioner body. install automatic tensioner unit to cylinder block. Tighten bolts to 22-27Nm. Fit timing belt in anti-clockwise direction, starting at the tensioner pulley. Slacken tensioner pulley bolt. Turn tensioner pully clockwise to temporarily tension belt. Tighten bolts to 43-45Nm. Turn crankshaft slowly 1/4 turn anti-cockwise. Turn crankshaft clockwise until timing marks alligned. Slacken tensioner pully bolt. Fit tool to tensioner pulley. Tool No 09244 28100. Apply clockwise torque of 2,6-2,8 Nm to tensioner pulley. Tighten bolt to 43-45Nm. Insert special tool in timing belt rear casing. Tool no 09244-28000. Screw in tool until pin can be removed from automatic tensioner unit. Remove special tool. Tool nr 09244-28000. turn crankshaft two turns clockwise. Wait 15 minutes. Ensure timing marks aligned. Check extended length of pushrod is 3,8-4,5mm. Install components in reverse order of removal. Tighten crankshaft pulley bolts, Tighten torque 20-30Nm

Nov 01, 2009 | 1995 Hyundai Elantra

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

1994 saab 900 se replacing timing belt


STEP 1 Remove Air Filter. STEP 2 Loosen the bolts securing the crankshaft pulley. Remove the load from the belt tensioner by turning the belt tensioner pulley locking bolt forward in the car using a 15 mm wrench. Remove the belt from the coolant pump pulley and slowly release the belt tensioner. STEP 3 Remove the belt tensioner and remove the steering pump pulley STEP 4 Remove the water pump pulley use the engine bracket to pry against. STEP 5 Remove the timing cover and Remove the right-hand front wheel and the cover in the wheel housing. STEP 6 Remove the crankshaft pulley (undo the six bolts but do not remove the centre bolt). STEP 7 Place the engine top dead center and Zero the engine. The markings on the camshaft sprockets and timing cover should be in alignment as also should the marking on the crankshaft. Use locking tools 83 95 006 and KM-800-2 for the camshaft sprockets and locking tool KM-800-10 for the crankshaft (These tools can be purchased from Saab (18774177222) or from Baum Tools). STEP 8 Before removing the toothed belt mark its direction of rotation . To facilitate refitting the belt can be marked at both the camshaft marking and the crankshaft marking. STE9cc7b85.jpgP 9
STEP 10 Fit the toothed belt according to the marked direction of rotation. Use setting tool 83 95 006 to keep the belt in place and adjust the tensioning roller loosely by hand to prevent the belt from jumping off. Adjust counterclockwise. Fit a section of the toothed belt and fit tool 83 93 985 to measure the belt tension. Loosely tighten the centre bolts of the adjusting rollers. Adjust the lower adjusting roller counter clockwise to a belt tension of 275-300 Nm. Turning torque 30 lb.ft ft ******The adjustment of the belt tension is for preparation ONLY and must not be used as a check when the belt adjusted for the final time! STEP 11 Turn the engine over two revolutions until just before the zero mark and place the locking tool on the crankshaft. Carefully turn the crankshaft in the direction of engine rotation until the arm rests against the coolant pump's flange and then tighten the arm. Fit setting tool 8395006 and check that the markings on the camshaft sprockets are aligned with the markings in the tool. ********Check that the A marking is approximately 2mm above B marking. If the distance is less readjustment is necessary. STEP 12 Fit the crankshaft pulley and Tighten to a torque of 15 foot lbs. STEP 13 Reinstall the inner wheel cover and front right wheel.
STEP 14 Reinstall Timing Cover.
STEP 15 Reinstall the water pump pulley use the engine bracket for leverage. STEP 16 Reinstall the power steering pulley and tighten to 6 foot lbs. STEP 17 Reinstall the belt tensioner and tighten to 30 foot lbs. STEP 18 Remove the belt tensioner load/pressure by turning the belt tensioner pulley locking bolt forwards in the car using a 15 mm wrench. Install the belt on the coolant pump pulley. Carefully release the belt tensioner. STEP 19 Reinstall the Air Cleaner and hoses that accompany Release the belt tension and remove the toothed belt.

Jul 18, 2008 | 1994 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...