Question about 1999 Chevrolet Blazer

1 Answer

How do I reset the anti theft system in my Blazer after installing a new ignition and key?

How do I get a 1999 Blazer with an anti theft system to run after installing a new ignition.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 21,873 Answers

You need to have a new key cut using the same blank that fit the truck before. The key blanks have a chip that the computer "reads" to allow the engine to start. There are about 10 different chips.
A locksmith or the dealer should be able to read the old key to find the new blank that matches it.

Posted on Dec 02, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset pats


Here is a post from a Ford Forum explaining the anti-theft system and the ignition key issue.

Ford F150 99 150 ignition anti theft question

Jan 13, 2015 | 1999 Ford F150 Regular Cab

3 Answers

My car wont start ,how do I reset the theft system on a 1999 monte carlo


Is the theft light on the dash lit ? If so turn the key onto the run position till the theft light goes out, about 10min. Turn key off for a few min. then start , hope that helps. If not have to have it checked for codes in the (BCM) body control module or the (PCM) powertrain control module !

Dec 21, 2014 | 1999 Chevrolet Monte Carlo

1 Answer

How do i get my computer to relearn my key on a 1999 chevy blazer?


The key lock is worn out. Use an ohm meter and read the chip in the key. There are 15 different codes. Write the number down. Then get a bypass kit from radio shack or an electronics store. Pull the two wires that go to the ignition lock. Put a resistor on the ends of the wires that match the resistance(+ or - 10 %) you read from the chip. This will keep your truck running. Even with a blank key/no chip

Aug 18, 2014 | 1999 Chevrolet Blazer

1 Answer

Need to reset the anti-theft system


I don't know your vehicle but each vehicle with an anti-theft is different. Some you have to put the door key into the drivers door and turn. Some you need to put the key in the front passenger door and turn. Some you put the key in the ignition. Try each one until it is reset.

Nov 08, 2013 | 1999 Saab 9-5

1 Answer

How to disable or reset anti theft system for 1999 navigator


YOU CANT DISABLE OR RESET THE ANTI THEFT SYSTEM. YOU NEED CODE SCAN FIX. PROBLEM WITH ANTI THEFT SYSTEM CAUSED BY KEY ITSELF WORN OUT OR FAULT IN THE ECM IMMOBILIZER READ COIL OR IN THE IGNITION SWITCH BAD.

Aug 02, 2011 | 1999 Lincoln Navigator

3 Answers

How do you reset anti theft on a 2007 equinox


TURN ON IGNITION SWITCH TO ON POSITION.ENGINE OFF.REPEATEDLY PRESS VECHICLE INFORMATION BUTTON UNTIL PRESS TO RELEARN REMOTE KEY IS DISPLAYED.PRESS SET RESET BUTTON UNTIL REMOTE KEY LEARNING ACTIVE IS DISPLAYED. IF THAT PROCEDURE DONT WORK.INSERT MASTER KEY INTO IGNITION SWITCH.NOW SWITCH IGNITION ON SWITCH IGNITION OFF.REMOVE MASTER KEY.WITHIN 10 SECONDS INSERT NEW KEY.SWITCH IGNITION ON.ENSURE SYSTEM WARNING LAMP SWITCHES OFF.NEW KEY NOW PROGRAMMED.IF YOU STILL HAVING PROBLEM RESETING THEFT SECURITY SYSTEM THE DEALERSHIP HAS TO FIX.REPROGRAM IT.

Mar 14, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

I had a key made and it desabled the security system in my 1999 mercury cougar and now the car wont start and I need to have it reset.


All you have to do to reset the antitheft system is to lock the doors with the key fob.

Your new key has to be programmed to your engine computer (PCM) before it will work.

To program, follow the directions in your owner manual. You need 2 already rpogrammed keys to do this.

If you don't have 2 programmed keys, your dealer will have to use his diagnositc tool to retrieve the information from the computer. Always have 2 programmed keys. I actually keep 3 in case I lose one, I still have 2 to program a 3rd one myself.

If you have AAA, have it towed to the delaer as a "no Start" so you don't have to pay the tow charge.

I assume this new ket is your only key now, or you could drive to the dealer with your spare key.
-------------------------------------------------
SECTION 419-01B: Anti-Theft - Passive 1999 Cougar Workshop Manual GENERAL PROCEDURES Procedure revision date: 09/14/2001
Key Programming Using Two Programmed Keys NOTE: This procedure only works if two or more programmed ignition keys are available and it is desired to program additional key(s). If two keys are not available. For additional information, refer to Key Programming - Erase All Keys and Program Two Keys in this section.
NOTE: PID SPARE - KY must be enabled for this procedure to operate. If this PID is not enabled, refer to Security Access then select Spare Key Programming Switch; Enabled.
NOTE: If the programming procedure is successful, the new key(s) will start the vehicle and the anti-theft indicator will illuminate for approximately three seconds.
NOTE: If the programming procedure is not successful, the new key(s) will not start the vehicle and the anti-theft indicator will flash. If the programming procedure was not successful leave the ignition switch in the RUN position for at least 30 seconds, repeat the Key Programming procedure from Step 1. If the failure repeats, refer to Diagnostic and Testing to review DTCs an carry out Pinpoint Tests.
NOTE: A maximum of eight ignition keys can be programmed to a passive anti-theft system (PATS) equipped vehicle.
NOTE: If the steps are not carried out as outlined, the programming procedure will end.
NOTE: Ignition keys must have correct mechanical key cut for the vehicle and must be a PATS encoded key.
  1. Insert first programmed key into ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain ignition switch in the RUN position for one second).
  1. Turn ignition switch to the OFF position and remove the first key from the ignition lock cylinder.
  1. Within five seconds of turning the ignition switch to the OFF position, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain the ignition switch in the RUN position for one second).
  1. Turn the ignition switch to the OFF position and remove the second key from the ignition lock cylinder.
  1. Within ten seconds of turning the ignition switch to the OFF position , insert the unprogrammed ignition key (new key) into the ignition lock cylinder and turn the ignition switch from the OFF position to the RUN position (maintain the ignition switch in the RUN position for one second).
  1. If it desired to program additional key(s), repeat the applicable key programming procedure from step 1.
  2. ----------------------------------------------------------------------------------------------------------------------------------
Passive Anti - Theft System (PATS)
The Passive Anti-Theft System (PATS) is fully passive in operation and requires no special procedures by the driver to arm or disarm the system. It is invisible to normal scrutiny and is operated by a miniature transponder within the key body. The transponder communicates with the powertrain control module through a transceiver mounted around the ignition switch lock barrel. The PATS functionality is incorporated within the powertrain control module.
PATS may be identified by a larger than normal sized ignition key. A larger sized ignition key indicates the presence of the transponder that controls the system.
The transponder code reading is carried out when the key, having been inserted into the ignition lock barrel, is turned from position ``0'' to position ``II'' to crank the engine. If the PCM receives the correct code, the engine will start. If the PCM receives either no code or an incorrect code the engine will not crank and PATS remains armed and the engine immobilised.
Anti-Theft Indicator
Whenever the ignition is switched on the anti - theft indicator will remain on for three seconds while the system reads the ignition key code.
The anti - theft indicator will flash rapidly or glow continuously after the initial three seconds to indicate the PATS has immobilised the vehicle.
For additional information on the PATS fault codes, refer to the Diagnosis and Testing section
-------------------------------------------------------------------------
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over four quadrillion combinations.
Each encoded ignition key must be programmed into the vehicle's powertrain control module (PCM) before it can be used to start the engine. There are special diagnostic repair procedures outlined in this manual that must be performed if an encoded ignition key needs to be replaced
------------------------------------------------------------------------

Dec 16, 2010 | 1999 Mercury Cougar

1 Answer

Anti theft lock


disconnect the battery for 3 mins

May 04, 2010 | 1999 Ford F150 Regular Cab

3 Answers

How to reset my factory car alarm in a 1999 mercury cougar v4 2.0? thanks


1999 cougar. before they tell me I need a fuel pump I want to be SURE the anti theft system has not shut off the fuel to the engine.
how do I confirm that?

Dec 08, 2008 | 1999 Mercury Cougar

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...