Question about 2007 Pontiac G6

1 Answer

I have a 2007 Pontiac G6. The wipers stop half way thru cycle and do not return to off position what do I need to do to fix this. I changed the wiper motor and needed to replace bushings now it is all

I have a 2007 Pontiac G6. The wipers stop half way thru cycle and do not return to off position what do I need to do to fix this. I changed the wiper motor and needed to replace bushings now it is all out of wack.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

Did you replace all the bushings? Pay particular attention to the portion of the linkage that converts the rotary motion of the motor to the linear motion of the rods which in turn drive the wipers. A loose bushing or mount here will not allow the motor to get past the point where the direction of the rods reverses

Posted on Dec 04, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

autodr
  • 260 Answers

SOURCE: 2001 Pontiac Bonneville SE, wipers won't go to rest postion.

the "horizontal park" mechanism is in the actual wiper motor assy.

Posted on Dec 05, 2008

  • 1 Answer

SOURCE: 2000 pontiac montana wipers stuck

This has happened a couple of times on my 1999 Pontiac Montana. Here's what I did to fix. Open the hood. Remove the shield over the the wiper cam mechanism on the passengers side. This is easy to access. Road salts and other dust and dirt gets in there and causes the sticking problem. Spray WD-40 in between the parts. Get in there with that little red spray straw and saturate it good, flush junk out. Get in the car and try the wipers. If I remember, you might have to manually place that little knob or lever on top of the cam in the opposite position to get it to resync, but try it first. Be sure the wipers are off when you're spraying the WD-40 so you don't injur your hands. I've had to do this twice and it worked both times.

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 2001 Pontiac montanaThe front wipers park in the up position

This is a common problem with Chevy Venture, Olds Silhouette, and  Pontiac Montana. The mechanical wiper drive and parking cam assembly, if it's not broken, needs adjustment. The spring loaded stop arm should engage the vertical tab on the assembly mounting plate when the wiper motor reverses. See pic.  9a7b0af.jpg
I will upload the instructions to fix this problem, if there is interest.

Posted on Jun 01, 2009

  • 12104 Answers

SOURCE: pontiac g6 2006 wipers stopped movement while

either linkage broke/ jammed or motor is stuck -makin noise but not movin open hood and with wiper on feel motor- its on firewall-for movement if moving turn off motor now try to move wipers if move freely than they are broken off or have disconnected from the motor need to remove the cowl to access the wipers linkages

Posted on Mar 13, 2010

omaromid
  • 332 Answers

SOURCE: How to clean O2 sensor on a 2007 Pontiac G6?

O2 sensor are located before and after Catalytic Converter ( exhaust system of your car). If you car's engine is 4 cyl you have 2 O2 sensors and if you car's engine is 6 cyl then you have 4 O2 sensors ( for each bank, 2 for left bank and 2 for right bank). Hope it helps and comment if you need more advice. Please don't forget to rate the answer it helps with my ratings, thanks!

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

2 Answers

2007 pontiac windshield wipers stopped working and you can hear the motor still runs


Wiper Motor
  1. Remove finish caps.
  2. Make reference marks for installation and remove wiper arms.
  3. Remove the air inlet grille panel.
  4. Remove the bolts attaching the wiper module to the plenum.
  5. Carefully lift the wiper module out of the plenum.
  6. Disconnect the electrical connector from the wiper motor.
  7. Disconnect the clip retaining the electrical harness to the wiper module.
  8. Remove the wiper module assembly from the vehicle.
  9. Remove the wiper motor.
pgb3h4h2w2cfkigtemgbipamp4qbq234aaads=
Wiper module assembly and motor removal
To install:
  1. Install wiper motor and mounting bolts, tighten to 40 inch. lbs.(4.5 Nm).
  2. Connect the electrical connector to the wiper motor.
  3. Connect the clip retaining the electrical harness to the wiper module.
  4. Position the wiper module assembly into the plenum.
  5. Install the fasteners attaching the wiper module assembly to the plenum, tighten fasteners to 89 inch. lbs. (10 Nm).
  6. Install the air inlet grille panel.
  7. Install wiper arms and align to reference marks.
  8. Tighten wiper arm retaining nuts to 26 ft. lbs. (35 Nm).
  9. Install finish caps.

2010-11-13_221323_2007_pontiac_g6_wiper_cowl-m3h04eiq4trf45oprzz0vy4e-4-0.jpg
https://www.youtube.com/watch?v=dHJli8z1_jI
https://www.youtube.com/watch?v=A3hLLrwz8wQ

May 23, 2017 | 2007 Pontiac G6

1 Answer

My windshield wipers turn on but only go half way and then stop. Then the motor sounds like it is grinding but the wipers won't return to the resting position or won't continue their cycle.


sounds like the gears inside the wiper motor are gone. replace the wiper motor and be sure to check the nylon bushing on the wiper control arms for wear.

Aug 02, 2013 | 1999 Dodge Neon

1 Answer

2009 pontiac g6 windshield wipers stopped working. I can move the wippers by hand and there is no resistance at all.. What could be wrong??


sounds like motors shot remove the cowling so you can see more
join a g6 forum find with google

Feb 07, 2013 | 2006 Pontiac G6

1 Answer

I have a 06 pontiac G6 and bought the bosch marathon blades, it shows that they should fit on the wiper arm but I can't get it to fit. Any suggestions would help, thanks.


I just put Bosch blades on my 2007. Those blades fit multiple vehicles so they include a squre plastic cap covering the point where your wiper arm attaches to the blade. I don't know which vehicle needs that cap, but the G6 does not. So throw it away. Then it will work fine.

Jan 02, 2012 | 2006 Pontiac G6

1 Answer

How do you remove a wiper arm off a 2007 g5.


Hello,

To remove the wiper arm of your pontiac g6, take a close look of the wiper arm, check the lower end and you will see a plastic cover covering the bottom part, you will have to apply force in pulling it up then you unscrew the screw that is holding the wiper down, then you lift off the wiper arm.

Follow these steps:
  1. Align the rubber claw channel on the sides of the wiper blade element with the wiper blade claws in the wiper arm.
  2. Slide the blade element into the arm. Guide the element through each set of claws on the arm until the element snaps into place in the arm notches.
  3. Position the blade with the element facing up. Insert the hooked end of the wiper arm into the opening in the middle of the blade. Hook the end of the arm over the pin inside the blade and push it in securely until it snaps into place.
  4. Flip the blade around so the wiper element is facing the windshield and lower the wiper arm until the blade element lays fully against the windshield.
Hope this helped.

Take care and good luck

Jan 09, 2011 | 2006 Pontiac G6

3 Answers

Pontiac g6 2006 wipers stopped movement while driving. what could this be from? I already checked fuses. i hear the motor running making noise.


either linkage broke/ jammed or motor is stuck -makin noise but not movin open hood and with wiper on feel motor- its on firewall-for movement if moving turn off motor now try to move wipers if move freely than they are broken off or have disconnected from the motor need to remove the cowl to access the wipers linkages

Mar 13, 2010 | 2006 Pontiac G6

2 Answers

2006 pontiac montana i cant stop wiper blades mid stroke to change them cant reach them when they return to down in hood again


when running the wipers turn the key off upon were you want the wiper to be positioned at for your work

Jan 01, 2010 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
2007 Pontiac G6 Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...