Question about 2004 Dodge Durango

1 Answer

Where is egr location on a 04 durango 4.7

What is the location of the egr valve

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,049 Answers

, the EGR on a 4.7 is attached to the rear of the left cylinder head, instead of on the front of the right cylinder for the 5.7.

I googled this Hope it helps.

Posted on Dec 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: Location of EGR valve on 2005 Dodge Durango

If I had been him, I would have talked you into a Chilton or Haynes manual for your car. They are easily detailed enough to show you the location and  Iwould be surprised if a chain operation like AZ didn't have the right one on hand.

Posted on Dec 15, 2008

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

  • 116 Answers

SOURCE: egr valve dodge durango

if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Posted on Apr 24, 2009

Murphybanton
  • 2004 Answers

SOURCE: location of egr valve?

The EGR Valve and transducer is mounted near the throttle body. 42224993.gif

Visit http://autorepair.about.com/library/faqs/bl948e.htm


Rate this fixya.

Posted on May 27, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the egr sensor located on 05 durango


The egr sensor is built onto and is part of the egr valve. Depending on what engine you have depends on where the valve is located. On 5.7 engines its in the front. On 3.7 and 4.7 its in the rear of the engine.

Apr 30, 2011 | 2005 Dodge Durango

1 Answer

How do I install an EGR valve for 2005 dodge durango?


To install the EGR Valve on a 2005 Durango first it is necessary to remove the air intake hoses and palce them to the side. Next, in order to get the EGR valve you will need to remove the windshield wiper motor, which is a pain but necessary to do get to the EGR valve. After removing all of the itemsthat are in the way you will be faced with a task that will try your patience, the EGR valve is located on the right side of the motor, (as if you were facing the motor from the front) just behind and to the rear of the throttle body. After you locate it you will need a rachet with a flexible head because it is fairly difficult to reach otherwise. A mirror and light will also help so you can see what you are doing since the EGR valve is located in such a hard place to see and get to that you will only be able to see part of it while you are removing the screws. After removing the EGR valve, simply reversethe procedure and your done. P.S. I own a 2005 Dodge Durango SLT with a 4.7L engine and I replaced mine this year after a check engine light came on and I checked the code on the OBD. By the way the EGR valve is a pain in the rear to change. Good luck!

Jun 29, 2010 | 2005 Dodge Durango

1 Answer

Where is the EGR Valve on a 2004 Dodge Durango Limited, V8, 5.7L Hemi? Is a hard operation to replace?


Have not replaced the EGR on my 04 Durango as of yet, but if you look into the the passenger side front fenderwell you will see part of it. Usually 2-4 bolts and the harness connector are all that is required.

Chrysler EGR valves are not known for their reliability.

Don

Apr 14, 2010 | 2004 Dodge Durango

1 Answer

Hesitation taking off from complete stop in my 04 Dodge Durango


it could be several things but with out proper diagnostic equipment its pointless to get into it, some times its best to bring it to the dealer,they work on their vehicles more than other shops and know them better as you already know your EGR was changed cost you money and its still the same.hope this helps you

Feb 12, 2010 | 2005 Dodge Durango

1 Answer

Need to locate EGR valve on dodge durango 2005


EGR VALVE LOCATED ON THE INTAKE.IT HAS A SMALL ROUND LOOKINGIT HAS A METAL FLEXIBLE PIPE THAT CONNECTS TO THE EXHAUST MANIFOLD.

Feb 01, 2010 | 2005 Dodge Durango

1 Answer

Where is the egr valve located on a 04 dodge 1500 truck


Passenger side front of cylinder head below the alternator. Look for electric pigtail of alternator.
Total of 4 bolts, 2 of them 8mm and 2 10 mm.

Nov 07, 2009 | 2004 Dodge Ram 1500

1 Answer

Need to replace egr valve, but don't know where it is located


Your going to have lay on the engine and do the job blind, If you have a machanic's mirror that would help.
The EGR is located on the rear driver's side head. If you look at left side and to the rear of the plastic intake manifold, you will see and metal tube that makes a 90 degree turn. Just follow it to the rear of the engine and you'll find where the EGR valve.
Most guys remove the EGR tube and valve together, but you can take the Valve off on it's own. Here's the easy way but more work by taking the tube off with the EGR valve.
Remove the two 10 mm bolt that holds the EGR Valve to the head,and remove the Valve and tube together. The bolts go straight down from the top. Don't bother looking for then, your going to have to feel for them.
WHen your putting things back together, leave the the tube loose from the valve or your going to have a hard time putting the bolts back to the Valve to the head joint.
After your done putting everything back together, disconnect the battery for a few min and turn on the lights to charge down any power to clear any false codes. 
Good luck and hope this helps.

May 06, 2009 | 1999 Dodge Durango

2 Answers

Egr valve dodge durango


if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Apr 17, 2009 | Dodge Durango Cars & Trucks

1 Answer

Location of EGR valve on 2005 Dodge Durango


If I had been him, I would have talked you into a Chilton or Haynes manual for your car. They are easily detailed enough to show you the location and  Iwould be surprised if a chain operation like AZ didn't have the right one on hand.

Dec 10, 2008 | 2005 Dodge Durango

Not finding what you are looking for?
2004 Dodge Durango Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...