Question about Chrysler Cars & Trucks

1 Answer

How to change lower control arm on chrysler town country

Nat

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 4,340 Answers

Marc,

This job requires specialized tools and is truly one of those man against beast with hammer type of job. Consider having a tire shop do this.
Here is my concern: IF you release the wrong thing, you can have the full fury of your spring be released. This can and will kill you or cause unreal body harm.

IF you understand how the spring works on your vehicle, and how you can safely unload it, you can rent spreader tools, spring compression tools, and most else at your local parts store. But this job is not like mowing the grass, more like digging up the front yard. Yeah, you can do it, but do you really want to?
It needs alignment when you are finished.

Posted on Dec 01, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

emissionwiz
  • 76846 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

polarcycle
  • 1392 Answers

SOURCE: right power seat will not lower

You need a new seat track. The motor is binding, and needs to be replaced.

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulls to left while hard acceleration pulls to the right after shift and rpm's drop off


Probly done wrong. Get it realined or havit inspected at a specialist not a dealer. Also send issue to majicmech@aol.com

Sep 05, 2016 | 2006 Chrysler Town & Country

1 Answer

Clunking noise when turning steering wheel going slow around corner


A lot of these Chrysler Town and Country vans had issues with the front stabilizer bar end links, usually you wont feel them move if you try to move them by hand, but they will make an awful noise clunk noise when turning or going over bumps slowly, i would suggest replacing the end links and that should take car of your clunking issue. Also the front lower control arm bushings separate as well and can cause this noise as well.... but i would replace the end links as a first step and go from there.... Hope this helps..

Sep 27, 2012 | 2003 Chrysler Town & Country

1 Answer

Need to change fuel filter on Chrysler town and country...2001...Can't find it


Usually underneath the rear above the trailing arm. If not , same area but on the left(driver's side) frame rail.

Apr 30, 2011 | 2001 Chrysler Town & Country

1 Answer

How do i get the rear wiper arm off a 2000 chrysler town n country...im replacing the motor


Look at the wiper arm. Where the shaft comes through there is a cap on the arm. Pop it up and you will see a nut remove nut and you should be able to get arm off.
Hope that helps!

Mar 06, 2010 | 2000 Chrysler Town & Country

1 Answer

Need to replace a wiper motor on a 2002 chrysler town and country mini van. how is this done?


Remove the wiper arms (pop off the caps at the base) and the 15mm nut. Take out the screws that hold down the wind shield cowl lift it away to expose the washer hoses. Unplug the wiper motor (center driver's side) by pulling out the red clip on it and squeezing the tab. Remove the 13mm nut from the wiper motor idler arm and take out the 3 10mm bolts that hold it in place. Squeeze it out from under the wiper transmission, or loosen the lower bolts. You'll see them. Not a difficult job, just take your time.

Hope I've helped.

Mar 06, 2010 | 2002 Chrysler Town & Country

1 Answer

Oil starved rocker arms on a 3.8 l 1999 chrysler


Add a 1/2 can of SEAFOAM per instructions on can to oil aand run for a week. change oil and ad remaining 1/2 can. worked for me

Jan 23, 2010 | 1999 Chrysler Town & Country

1 Answer

How do you get the wiper blade from the arm to


Push the tab up & the blade slides inward. Most auto stores will change the blades for FREE if bought there.

Jan 08, 2010 | 2003 Chrysler Town & Country

1 Answer

Replacing lower control arms


man,u need help from a automotive technician..go find one and ur problem will be solved..hehehe..its difficult to explain it here..many things to be done to replace that..

Jul 06, 2009 | 2001 Chrysler Town & Country

1 Answer

Do I have to change the lower control arm to change the ball joint in a 2003 town and country?


I know the best way to verify is to call the dealership and ask to talk to parts department. I know that you can buy the ball joints separate but they are pressed in and pressed out, not the bolt in kind. Call to verify though.

Mar 25, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...