Question about 2007 Mercury Mountaineer

1 Answer

Cant turn key to off and remove with out disconnecting electrical connectors?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 1,147 Answers

Could be your shifter is out of adjustment. If it doesn't go all the way into park on shifter, yet transmission is in park, then the shifter is moving to a far enough position to remove the key.

Posted on Dec 01, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 07 f150 4.6L V8 and I need to replace the Bank 1 sensor 1 oxygen sensor but cant figure out which sensor it is since there are 4 sensors. Where can I find a picture of the location?


Heated Oxygen Sensor (HO2S)- The Bank 1 Sensor 1 tells me that it's an upstream O2 sensor. The larger the number the further down the line of the exhaust it is. Removal & Installation 4.2L Engine ford-04-42-2750.gif
To Remove:
  1. Raise and safely support vehicle.
  2. Disconnect battery ground cable.
  3. Detach electrical connector from right inner fender splash shield (if necessary).
  4. Remove right inner fender splash shield (if necessary).
  5. Disconnect heated oxygen sensor electrical connector.
  6. Remove heated oxygen sensor.
To Install:
  1. Apply anti-seize lubricant to heated oxygen sensor threads.
  2. Install heated oxygen sensor. Torque to: 34 ft-lbs (46 Nm)
  3. Connect heated oxygen sensor electrical connector.
  4. Install right inner fender splash shield (if necessary).
  5. Attach electrical connector to right inner fender splash shield (if necessary).
  6. Connect battery ground cable.
  7. Lower vehicle.
4.6L and 5.4L Engines ford-04-46-2751.gif
To Remove:
  1. Raise and safely support vehicle.
  2. Disconnect battery ground cable.
  3. Disconnect heated oxygen sensor electrical connector.
  4. Remove heated oxygen sensor.
To Install:
  1. Apply anti-seize lubricant to heated oxygen sensor threads.
  2. Install heated oxygen sensor. Torque to: 34 ft-lbs (46 Nm)
  3. Connect heated oxygen sensor electrical connector.
  4. Connect battery ground cable.
  5. Lower vehicle.

Nov 07, 2010 | Ford F-150 Cars & Trucks

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

1 Answer

Replacing the agnition switch how to?


SECTION 211-05: Steering Column Switches 2001 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/15/2004 Ignition Switch Removal
  1. Depower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).
  1. Detach the instrument panel lower panel.
    1. Remove the screws.
    1. Release the fastener.
    e0001946.jpg
  1. Remove the instrument panel lower panel.
    • Disconnect the hood release.
    • Disconnect the data link (DLC) electrical connector.
    e0009940.jpg
  1. Detach the steering column upper shroud.
    • Using a thin bladed screwdriver, release the two clips (one each side).
    e0000671.jpg
  1. Remove the steering column lower shroud.
    1. Release the steering column locking lever (if equipped).
    1. Remove the screws.
    • Remove the ignition key.
    e0000670.jpg
  1. Disconnect the electrical connectors.
    • Disconnect the ignition switch electrical connector.
    • Disconnect the turn signal/flash-to-pass switch electrical connector.
    e0001776.jpg
  1. Remove the ignition switch.
    • Release the clips.
    e0000394.jpg
Installation
  1. To install, reverse the removal procedure.
  1. Repower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering (501-20B Supplemental Restraint System, GENERAL PROCEDURES).

2010&c18=modelyear&c20=g17614&c35=wsm%2cignition%20switch%2cs1y%2c211-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 01, 2010 | 2001 Ford Focus

1 Answer

Steering wheel covers


I hope this helps....these are the steps to removing and replacing the cylinder:

  1. Remove the knee bolster.
  2. Remove the steering column trim covers from the steering column.
  3. Disconnect the steering column electrical connectors.
  4. Remove the wire harness assembly from the steering column and the wire harness strap.
  5. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
  6. Remove the key alarm connector from the lock module assembly in the following way:
  7. Rotate the key alarm connector 90 degrees.
  8. Pull the key alarm connector out of the lock module assembly.
  9. Remove the passkey connector from the lock module assembly.
  10. Remove the connector from the electric park lock, for vehicles equipped with floor shifters.
  11. Remove the ignition switch from the lock module using tool J42759 or equivalent.
To install:
  1. Install the ignition switch to the lock module
  2. Install the key alarm connector into the lock module assembly.
  3. Push the key alarm connector into the lock module assembly.
  4. Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
  5. Install the passkey connector into the lock module assembly.
  6. Install the connector to the electric park lock, for vehicles equipped with floor shifters.
  7. Slide the 2 connectors of the turn signal and multifunction switch into the bulkhead connector.
  8. Attach the wire harness assembly to the steering column wire harness strap.
  9. Connect the steering column electrical connectors to the vehicle.
  10. Install the trim covers to the column.
  11. Install the knee bolster.
  12. Enable the SIR system.
  13. It may be necessary to reprogram the theft deterrent system if the module was replaced.

Mar 06, 2010 | 2001 Chevrolet Suburban

1 Answer

Dashboard lights burning out, down to 1 illuminating tach, speedo, gas gauge. How complicated to replace?


one hour job. find bulb part number in bulb chart in owner manual.

go here for villager help.

http://groups.yahoo.com/group/villagerquest/

Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
-------------------------------------------------------------------------------------------------
Instrument Cluster
Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
  1. Remove the four instrument cluster screws.
  2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).

Jan 13, 2010 | 1995 Mercury Villager

2 Answers

Got a 2000 chevy 3500 express van how do i get the old ignition switch out to replace it


remove the steering wheel , need a puller and locking ring tool, disconnect batt, turn the key to tho on position, and remove bolt that holds the tumbler in,

Nov 13, 2009 | 2000 Chevrolet 3500

1 Answer

Need to take out


Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.

Jul 06, 2009 | 1984 Chevrolet Camaro

1 Answer

Car was stolen broke the ignition


REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Feb 13, 2009 | 1992 Honda Accord

1 Answer

Need help with dash removal.


  1. Remove the A-pillar and cowl side Trim Panels
  2. Remove the front floor console.
  3. Depower the supplemental restraint system (SRS).
  4. Remove the instrument panel side finish panels.
  5. Remove the 2 steering column opening cover screws.
  6. Remove the steering column opening cover.
  7. Remove the 3 lower steering column cover screws.
  8. Remove the lower steering column cover.
  9. Disconnect the steering column electrical connectors.
  10. Disconnect the RH side bulkhead electrical connector.
  11. Disconnect the RH side body harness electrical connector.
  12. Remove the 2 parking brake release handle screws.
  13. Disconnect the LH side instrument panel electrical connectors.
  14. CAUTION: To avoid damage to the clockspring, do not allow the steering column shaft to rotate while the intermediate shaft is disconnected.
  15. Remove the pinch bolt..
  16. Disconnect the adjustable pedal electrical connector.
  17. Disconnect the brake light switch electrical connector.
  18. Remove the 2 LH instrument panel center brace bolts..
  19. Remove the 2 LH instrument panel center brace nuts.
  20. Remove the LH instrument panel center brace.
  21. Disconnect the transmission range selector lever cable.
  22. Disconnect the RH side bulkhead electrical connector.
  23. Disconnect the LH side body harness electrical connector.
  24. Remove the 3 ground strap bolts.
  25. Disconnect the inertia switch electrical connector.
  26. Disconnect the RH side instrument panel electrical connectors.
  27. Remove the 2 RH instrument panel center brace bolts.
  28. Disconnect the vacuum connector.
  29. Remove the 2 RH instrument panel center brace nuts.
  30. Remove the RH instrument panel center brace.
  31. Remove the cowl panel grille
  32. Remove the instrument panel bolt located under the cowl panel grille
  33. Remove the instrument panel defroster grille.
  34. CAUTION: To avoid damage to the sunload sensor and electrical connector, remove the grille just enough to disconnect the connector.
  35. Disconnect the sunload sensor electrical connector.
  36. Remove the 2 instrument panel top cowl bolts.
  37. Disconnect the antenna lead-in cable.
  38. Disconnect the RCM electrical connector.
  39. Disconnect the center ground strap bolt.
  40. CAUTION:To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
      • Before removing the instrument panel make sure all electrical connector wiring is free and not hindered.
  41. Remove the 4 instrument panel bolts.
  42. Remove the instrument panel.
  43. To install, reverse the removal procedure.

Feb 11, 2009 | 2005 Ford Explorer

Not finding what you are looking for?
2007 Mercury Mountaineer Logo

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...