Question about 2003 Chevrolet Chevrolet Malibu Base

Open Question

2003 chevy Malibu water pump replace

4 cyl engine water pump replacement flat rate

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 206 Answers

SOURCE: Replace the water pump on a 2002 Malibu

What size motor If it is a v6 most of them you are easy drian the radiator down take the pulley of the pump and you will remove the bolt and pump

Posted on Apr 05, 2009

lasvegasrich
  • 65 Answers

SOURCE: replacing spark plugs on a 2004 chevy malibu

2.2L Engine

  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Posted on Oct 07, 2009

Testimonial: "Thanks for the help, it was easy to change out the plugs with your info."

  • 3640 Answers

SOURCE: 2001 Chevy Malibu - have changed out thermostat

check to make sure fans are working for radiator. if not check coolant tempurature sensor, fuses, and relay. is all air out of coolant system!

Posted on Jul 07, 2010

tripletauto
  • 1450 Answers

SOURCE: location of water pump on 1998 chevy malibu with

your water pump is driven off of timing chain,it will be on back side of timing cover toward firewall down toward bottom. you have to remove timing cover and chain to replace pump

Posted on Aug 21, 2010

wyet_helps
  • 339 Answers

SOURCE: I have a 2008 Chevy

{: ) Code P0010 refers to a fault at the Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1. This code will set if the ECM (Engine Control Module) detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 3 s.
The service procedure requires close monitoring with a scan tool. Well it may be too technical for you, but simply put, it may require replacing the CMP actuator solenoid valve if it fails the component test. If the component is found to be okay, the circuit and wirings should be checked for possible shorts or open, and also the signal performance. If all circuit tests proved normal, a replacement ECM may be recommended.
If the engine light and code is consistently present, most likely it's the actuator solenoid valve. Check it out with your trusted mechanic. Goodluck.

Posted on Aug 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check Engine Light


they might have left wires loose on the cam or crank sensor

Mar 30, 2014 | 2004 Chevrolet Malibu

1 Answer

98 Chevy Malibu won't start after replacing thermostat?


replace thermostat did bleed coolant system check coolant level.because if not engine could have overheated and blowed headgaskets warp or cracked the heads check engine compression.sound like engine got too hot.

Jan 08, 2013 | 1998 Chevrolet Malibu

1 Answer

2003 chevy malibu gas gauge always on empty, replaced the fuel pump


Need to replace the sensor inside the gas tank. I have a 2008 Malibu with the same problem. It was a faulty fuel gauge sensor.

Jan 31, 2012 | 2003 Chevrolet Malibu

1 Answer

My 2003 chevy malibu is overheating two notches then goes down then up. Not leaking fluid. I replaced resevior and sparks plugs and wires. What could cause this?


did you replace the cap too? try checking out the water pump or thermostat. mine does that too but i have A LOT of other problems with the car so i still dont know..but my radiator/fan was sitting 4 inches too low so now that i got it up well see what happens.

Sep 07, 2011 | 2003 Chevrolet Malibu

2 Answers

My 2002 chevy malibu 4 cyl is running hot, some water coming down off the right side of the engine


please double check your vehicle application, there is no chevy malibu with 4 cylinder engine. there is only a 3.1 L engine in this model

Mar 16, 2010 | 2002 Chevrolet Malibu

2 Answers

2003 chevy malibu. brakes go to the floor.


Master cyl. is "bypassing" replace it, but make sure you "bench bleed " it first !
After that then have someone get in car and pump up brakes, you then bleed them one at a time.
MAKE sure not to let the master cyl. res. go dry or you will be there ALL DAY bleeding !

Feb 05, 2010 | 2003 Chevrolet Malibu

2 Answers

Where is the water pump located on a 1998 chevy malibu 4 cyl?


It is located at the rear of the engine between the timing cover and exhaust manifold. You will have to remove the manifold to ge to pump. It runs off the timing chain. It would be a wise decision to take to an experienced mechanic.

Jul 02, 2009 | 1998 Chevrolet Malibu

1 Answer

Replacing the water pump in a 1997 Chevy Malibu


if it got the 3.4 in it it a walk in the park. take the belt off 4 pully bolts then 5 water pump bolts clean off old gasket then reinstell. look at water pump real good it only goes on 1 way. good luck. o brake the pully bolt loose before you take the belt off.and youll need a small pan to drain anti freeze it

Apr 02, 2009 | 1997 Chevrolet Malibu

Not finding what you are looking for?
2003 Chevrolet Chevrolet Malibu Base Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...