Question about Cars & Trucks

1 Answer

Why leaking?Even if we change another valve is olso leaking.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 755 Answers

Be more specific , leaking on what ?

Posted on Dec 04, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Burning oil ,no leaks or smoke

how many miles?
can be bad rings.
or bad valve seals.
or both.
do a compression test then a leak down test, and bingo the answer.
if both pass, the valve seals are bad.
if not rings are bad, if the oil test for compression fails the valves them selves are bad, if the teaspoon of oil test , passes the rings are shot.
read up on all compression tests. using google, or by any car engine book, one that tells you how to test for this.

The leak down test, can even tell you which direction the leak happens
using a rubber hose to your ear.
i can hear air leak to crankcase, valve cover oil filler, oil dip stick hole, and to intake plenum and even hear it at exhaust ports. sure can.

one the oil control rings on old engines can stick down and be
near useless. stuck in the lands. seen many like that.

Id use the 2 gauge to judge engine condition,
if bad, its hopeless. (bottom end bad)
if good, all tests. then the valve seals are bad.
there is a way to change them head on car.
using shop air , or other wild tricks.

Feb 07, 2014 | 1995 Honda Odyssey

2 Answers

1998 Grand Marquis. Start goods. idols low. put in gear, stalls out. Changed fuel filter & had injectors serviced. Problem remains. Could it be the Transmission modulator valve?

I would check the operation of the idle speed control valve, it is what changes the idle speed when a load like the transmission is put on the engine, without it the engine will idle slow and stall out, this is even more apparent when reverse gear is selected or drive or the AC is tuned on. The ISC valve is located on the side of the throttle body top of upper intake manifold. Below is a picture of the ISC (idle speed control valve)

Sep 30, 2011 | 1998 Mercury Grand Marquis

1 Answer

2004 gmc yukon lite came on low oil pressure just had oil change 5 days ago checked it was low about a qt. Has 157,000 miles what can be the cause

There can be alot of causes, such as valve covers leaking, oil pan gasket leaking, oil filter leaking, rear main seal leaking, front timing chain cover seal or gasket leaking even bad rings. Does it smoke out of the back? Your valve seals could be leaking. Best way to find out if you have a leak is to inspect the valve covers manually, or take newspapers and lay them under the entire engine on the ground, and it will leave the tell tale stain of a leak. Hope this helps.

Jun 15, 2011 | 2004 GMC Yukon

1 Answer

How do I change my brake power booster in my 1989 Regency 88? My car does start and runs good, until you put it in gear and hit the brake. My brake petal is very hard to push. It will kill the engine when...

First inspect the vacuum check valve and the booster vacuum grommet for any leaks, even a pin hole in the check valve can also cause that to happen.

If the vacuum line to the booster is tight and has no air leaks, and no air leaks are in the vacuum check valve, then replace the booster unit.

Apr 19, 2010 | 1988 Oldsmobile Regency

1 Answer

2000 jetta auto trans won't shift out of park after starting

that is a TSB you may have a bad valve body, olso this condition may turn malfunction ligth on, or if you remove the air intake pipe
on trans there is a conector that go to trans valve body some time come lose pluged back an reset PCM if don't fixed will be the trans valve body

Mar 12, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

1992 Lincoln town car 4.6l

hi if you mean engine core plugs? as we know/call them in uk then yes! both on cyl heads and the more important (largest ) isbehind the flywheel this is the important one due to the cyl blck is the thinnest weaker part of the block/cooling system and should engine block freeze ??then this plug will pop out/leak as ice expands as you know? and consequently leak as ice melts? olso it is suseptible to rusting and eventually seep coolant hope this helps your querie ?

Jul 08, 2008 | 1992 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides