Question about 2006 Jeep Liberty

1 Answer

The tailgate lock and rear wiper will not work on my 2006 jeep liberty I also noticed it will not unlock at all with the key until im close to the driver door maybe related im not sure

Checked fuses

Posted by on

1 Answer

Without buying the factory service & diagnostic manuals
or cd---- your Not going to find anything

So you need a dealer or local shop-- that has the data & info
to find a problem

Posted on Dec 01, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 625 Answers

SOURCE: 2004 tahoe

make sure than you have not split any fluids on the passenger front door most of the times is where the module to control the windows and doors is located, try by unpluging the batterie and the after a minute plug it back and see what happend but if any of your ft doors have been split with liquid or rain has gone inside then most likelly the module got moisture and not working

Posted on May 31, 2008

SOURCE: tailgate stuck

The auto lock burned out you need to go to dealer and get ripped off for $300 to have them fix it. Make sure you tell them the exact problem since it took 3 mechanics two days to figure mine out after i told them what was wrong the first time. Not too swift there.

Posted on Aug 15, 2008

  • 7 Answers

SOURCE: tailgate door and window won't open

Check in your user's manual for your fuse location on the rear windshield wiper. These grand cherokee's have electronic actuators in every door. Inside these actuators they have very little motors and move everything via plastic. Very bad design flaw, as most of these actuators are 300-400 dollars to replace. You can find ones in salvage yards for 50 though. On your rear hatch, the door and the window are run by this actuator.

Posted on Sep 10, 2008

  • 1 Answer

SOURCE: 2002 Jeep Liberty, rear window latch is ''locked'' & window is open

i was having the same type of problem. we just put a couple of washers behind the latch and then adjusted the latch and it solved our problem.

Posted on Jan 31, 2009

VOLVOCHICAGO
  • 33 Answers

SOURCE: 1999 Volvo V70 - The tailgate door will not unlock

you will need new t gate lock assembly parts inside are worn out

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 corolla dash lights n tail lights went out. Checked fuses all ok.


tail Fuse 18--15 amp, interior fuse box.
Not only check the fuse, check the fuse circuit for voltage, hot all the time, use a test light to check for voltage.
There is another fuse and fusible link involved. First, check for voltage on the tail fuse.
Some people want to know exactly what the problem is w/o any testing, usually, I can't do that.

Feb 15, 2017 | 2008 Toyota Corolla

5 Answers

Fuse box diagram for 2001 Volkswagen Passat


its quite easy to spot a blown fuse generally a blown fuse looks like this with the wire cut in the middle.

9171423.jpg

Mar 22, 2009 | 2001 Volkswagen Passat

2 Answers

My 2011 Chevy Malibu tail lights are out, is it a fuse or bulb? Thanks


IF both lights are out most likely a fuse, check the drivers manual for location of fuse, check both sides of the fuse with a test light, must be voltage both sides, no voltage , cable from light switch to fuse faulty. voltage to only one side of fuse, fuse faulty. voltage to both side of fuse , cable to tail lights faulty, bulbs faulty or bad earth to tail lights.

Mar 03, 2016 | Cars & Trucks

1 Answer

Where is the license plate light fuse on 2003 chevy impala?


2000-2005 Chevrolet Impala Interior Fuse Check - 2003 ...

www.carcarekiosk.com/video/2003_Chevrolet_Impala_3.../fuse.../check
The video above shows how to check for blown fuses in the interior fuse box of your2003 Chevrolet Impala and where the fuse panel diagram is located.

Replace a Fuse: 2000-2005 Chevrolet Impala - 2003 ...

www.carcarekiosk.com/video/2003_Chevrolet_Impala_3.../fuse.../replac...
The video above shows how to check and change blown fuses in the engine bay of your2003 Chevrolet Impala in addition to where the fuse box diagram is ..

Dec 16, 2015 | 2003 Chevrolet Impala

2 Answers

Is there a way to unlock the rear door of a 2004 jeep liberty from the inside


If you hit the unlock button in the door 2 times, it should unlock the tailgate. Otherwise you may have to go back to the dealership and have them program a new remote for you. If the battery in your remote went dead, it may work again by replacing the battery.

Jul 11, 2014 | 2005 Jeep Liberty

1 Answer

Whats the ac fuse number


Get ready for some serious fuse checking. In the central junction box, check 10A FUSES 15, 17, 25, and 6 as well as 7.5A FUSE 19. In the battery junction box, check 40A FUSE 101, 30A FUSE 7, 15A FUSE 11, and 50A FUSE 102 as well as 15A FUSE 21.

Jul 11, 2014 | 2008 Lincoln Town Car

1 Answer

2006 jeep liberty rear lift glass won;t close


Mine did this too....the latch kept getting stuck. If you put the key in the ignition and unlock the power doors, pull on the gate door (don't open it, just enough to release the latch), and it should come out so the hatch will latch.

Feb 18, 2013 | 2006 Jeep Liberty

2 Answers

Gauge don work


check the fuse box

Nov 14, 2012 | Hummer Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

Not finding what you are looking for?
2006 Jeep Liberty Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...