Question about Saturn Cars & Trucks

1 Answer

I have a 1995 Saturn sl2. It pulls off really slow from dead stop and gradually picks up speed. The check engine code reading is code 43, "actuator lost power"

Change fluid and filter, check transmission plug and wiring, checked solenoids with multimeter. Changes gear at normal ratio with no hesitation. It drives good until you have to make a complete stop and all over again.

Posted by on

1 Answer

Why have you not looked up your OBD 1 fault code 43
& diagnosed it?

Also after that issue is resolved-- how about a blocked converter
if it is over tens years old?

Posted on Dec 01, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: 02 Neon won't shift out of second gear in Drive

Sounds like the valve body is loose, warped or blown

Posted on Apr 07, 2009

  • 1986 Answers

SOURCE: 2004 Audi A4 1.8 - jerks/jolts while accelerating from 0-20 mph

It sounds like there may be an issue with your ignition system.

Check the ignition wires, distributor cap, spark plugs.

Posted on Sep 09, 2009

  • 4 Answers

SOURCE: 1997 transmission Slow Acceleration

not sure if this is the answer yet but i have the same problem with the same codes i work at an auto parts store and a few of the techs that are customers have lead me in the direction of changing the ignition switch, i am doing it today will let you know if it solves the problem

Posted on Jan 27, 2010

  • 3640 Answers

SOURCE: po 742 code check engine light on.transmission

p0742 is torque convertor curcuit stuck on. good-day!

Posted on Aug 22, 2011

emissionwiz
  • 75814 Answers

SOURCE: 2001 ford taurus 3.0 v6 code p0306 misfire

Please go to this page for engine misfire causes.

Posted on Aug 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code 84 for 92 saturn sl2 check engine code


go to autozone they will give you a print out wile the thing to check. bobg22

Nov 12, 2009 | 1992 Saturn SL2

1 Answer

93 saturn sl2 when given the gas it want pick up speed


Do a back presure check by taking the 02 sensor out and placing a vacuum gage there to see how much back pressure it has. It maybe that the catylatic convertor is clocked...which could mean engine problems.

Oct 28, 2009 | 1993 Saturn SL2

2 Answers

Sep 13, 2009 - my car wont start but the battery is not dead. my check engine light is on. can i get a code for the check engine light myself or do i have to take it to a computer to read it. Its a 2002...


you need a reader pluged into your car to read any codes unless it is bluetooth set up...most likely not...too early in time for that yet....um maybe the starter relay or even the starter solonoid or loose battery terminal or broken connection in main + battery lead somewhare or someones tried to hot wire it

Sep 13, 2009 | Saturn SL2 Cars & Trucks

2 Answers

Engine light


most likely this is the O2 sensor for that cylinder bank is defective.

Jun 24, 2009 | 1993 Saturn SL2

1 Answer

1995 saturn sl2 when putting it into drive it slames real hard then it is slow going till the rpms get up then its fine any thoughts?


this might be a dumb quest. have you checked the trans fluid ? if so you might need a torque converter in a automatic . or clutch in manual trans.

Apr 09, 2009 | 1993 Saturn SL2

1 Answer

Saturn sl2 emissin problem


If the SES light is on, take a paper clip bend it in a u-shape and jump the scanner input positions A B. This should flash the ses in sequesces to give you the trouble code, Please see the following link. http://www.troublecodes.net/GM/ Refer to the code to see what the issue may be. SES lit means that there is a emmissions related issue. Refer to the other links for additonal information on O2 sensor resistance, and the egr valve solinoid. Check the EGR is relitive easy for operation. Remove the vaccum hose and place a hose of similar suckon the hose to pull vaccum if the diafram underneith retracts, hold the vaccum by plugging off the tube with your touge if the diafram retracts, will not hold the vaccum, it is bad. The solinoid should read 40-60 ohms if good. http://www.saturnfans.com/forums/index.php http://www.aldlcable.com/sc/pages.asp?pageid=21
http://www.saturnfans.com/forums/showthread.php?t=37884

Oct 03, 2008 | 1995 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...