Question about Cars & Trucks

1 Answer

Sante fe cranks but won't start new timing belt and camshaft sensor but still won't start got spark and got fuel ??

Posted by on

  •  patrick
    patrick Nov 30, 2014

    did you make sure the engine was at top dead center compression stroke and timeing mark in right place for the cam shaft before you put on new belt

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

When did this problem start

Posted on Nov 30, 2014

  • Jamie Nov 30, 2014

    I've had it for a week it just wouldn't start after being parked so I replaced crank sensor it didn't do any thing so I looked at timing belt it had wear marks so i changed it but it doesn't start it sounds close but doesn't fire

×

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 180 Answers

SOURCE: My 2004 hyundia Santa fe won't start it just die

Check fuses under the hood. When the crankshaft sensor shorts, it often blows this fuse. It is a 10 amp fuse. I don't remember what number it is off hand but it will be efi related.

Posted on Feb 18, 2011

  • 115 Answers

SOURCE: 04 Sante Fe 2.4L no spark no rpm pulse

rpm is regulated by the crank position sensor in all hyundai cars did one today

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would be wrong when my car has gas, but no spark?


2001 Sante Fe Won't Start, Cranks But No Spark. - Hyundai Forums ...

www.hyundai-forums.com/...santa-fe/112601-2001-sante-fe-won-t-start-...
Jul 23, 2010 - 10 posts - ‎3 authors I have a 2001 Hyundai Sante Fe that died on me while driving down my street. ... Thecar has many other unrelated problems and I am not sure I want to ... may be causing my two cylinder no spark and alleged fuel problem? 2006 Santa Fe 2.4 Engine swap-no spark
10 posts
Sep 24, 2012
No Start 2.4L Engine 2004 Manual
10 posts
Nov 26, 2011
Good Crank/Have Fuel pressure/NO IGNITION
10 posts
Oct 9, 2011
Car Cranks But Will Not Start
10 posts
Jan 16, 2008
More results from www.hyundai-forums.com

Engine cranks but won't start.What should I do. - YouTube

? 9:37
https://www.youtube.com/watch?v=jsQcLya1YLQ
Jan 24, 2014 - Uploaded by jimthecarguy
No Start Cranks Ok No Injection Pulse 2002 Hyundai Accent Easy Step By Step ... and car cut off, but would not restart. it sounds like it is starving for fuel. ... hi nice video man . i have no sparkno fuel .u think its the main? it was ...

Nov 26, 2015 | 2001 Hyundai Santa Fe

1 Answer

H my name is carl my 2002 Hyundai accent will crank over everything comes on but wont start there's no spark,and no power to fuel pump and i changed the crank shaft position sensor and still nothi


Have you checked the timing belt, it is most likely has stripped out teeth and not turning the camshaft(s). Pull the belt cover off the front of the engine and see if the camshaft pulleys rotate when cranking the engine over.

Sep 18, 2012 | 2002 Hyundai Accent

1 Answer

I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?


Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Mar 22, 2012 | 1999 Mitsubishi Eclipse

2 Answers

Wont start it cranks but nothing happens.wont turn over. put a new what you would call distributor. still nothing.


If the Starter isn't turning the engine over, but you hear a clicking sound, you may have a bad Starter.
If the Starter is turning the engine over, but you are getting no Spark, you may have a failed Camshaft or Crankshaft Position Sensor, or your Timing Belt may have jumped or broken(common on the neons).
If the Starter is turning the engine over, but you are getting Spark, you may have a failed fuel pump, fuel pump relay, or fuel pressure regulator.

Before you start replacing sensor, double check the Timing belt to ensure it hasn't broken or jumped, and check to see if you are getting a spark or not.

Mar 12, 2011 | 2003 Dodge Neon

3 Answers

The engine turnes but it wont start.


Free Auto Repair Advice by Professional Mechanics




Troubleshooting / Car Engine Cranks but Will Not Start / Engine Crank But Wont Start 2

* Why does my engine stall at idle?
* How do I change my spark plugs?
* Why does my engine stall?
* Why does the engine stall after replacing the battery?
* Why won't my engine crank over?
* How to retrieve trouble codes
* How to test fuel delivery system
* Engine cranks excessively
* Engine has excessive smoke
* Rapid ticking sounds when engine is cranked
* How to tune up your engine
* How to jump start your engine
* How to test an oxygen sensor
* How to open a car hood
* How a flywheel - flex plate works

Engine Cranks But Will Not Start

For an engine to run, you need three things to happen inside the engine, compression, fuel and ignition, without any one of these components the engine will not run. Follow the repair guide below:


Engine Configuration with Camshaft Operation

*

Compression - Engine compression caused by crankshaft rotation and pistons moving up and down inside the engine block. If the timing belt or timing chain fails it will cause the camshaft to become out of correlation with the crankshaft or allow the camshaft to stop rotating. Either of these conditions will cause the engine to lose compression and sometimes cause internal engine damage.
*

Fuel Delivery System - The fuel system includes: fuel pump, fuel injectors, pressure regulator, fuel filter and pressure lines. This system is used to supply fuel under pressure to the fuel injection system, the lack of fuel pressure or volume will cause the fuel delivery system to fail and the engine to stall or not start.
*

Ignition Spark Delivery System - The ignition system components include: spark plugs, spark plug wires, distributor (if applicable), crankshaft angle sensor, camshaft angle sensor, ignition coil, ignition module, knock sensor and PCM (engine control module). The engine relies on the ignition spark to be delivered to the combustion camber at the correct time. If the ignition spark stops or is delivered at the wrong time the engine will not run or run poorly.

If your engine cranks but does not start follow this troubleshooting guide:
* Step 1 - Anytime you have a problem with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) inspect all fuses using a test light and check the under hood power distribution center and under dash fuse panels. If all fuses test ok continue to the next step.
* Step 2 - To check for problems with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) and the fuses test ok a trouble code scan is needed to identify any system trouble. Use a simple scanner tool to retrieve trouble codes and see if they relate to the specific problem, like a crank angle sensor failure code. If the trouble code present does not pertain to the immediate problem like an EVAP code ignore it until a later time, after the car is running. The reason we repair non-related codes after the engine is running is because sometime false codes can be triggered by the engine not running. Once the engine is running again the code present might cycle and turn itself off. You might say "if the engine doesn't run shouldn't it have a trouble code?" Sometimes conditions occur that will not be detected by the computer, example: if the fuel pump fails the computer cannot detect the failure, so the engine doesn't start and the computer thinks everything is ok with no codes. If no trouble codes are present proceed to the next step.
* Step 3 - The spark plugs in your engine are used to ignite the compressed fuel air mixture. If the condition of the spark plugs are fouled by excessive fuel or carbon the engine will not start, backfire or run rough. Remove all spark plugs to inspect their condition. Please use this spark plug condition reference guide to see how the spark plugs are operating.
* Step 4 - Determine if the engine has compression, this can be done a number of ways but the most complete method is to perform a compression check. Remove the spark plugs and perform a compression test on one cylinder. If one cylinder has compression then the remaining cylinders usually will be close to the same. Crank the engine over about 5 seconds, normal compression readings should be between 125 psi and 160 psi on each cylinder. If no or little compression exists additional tests will be needed. The most common reason for an engine to lose compression is a timing belt or timing chain failure. If low or no compression exists remove the oil fill cap and observe camshaft rotation when the engine is cranked over. If no rotation exists the timing belt or chain has failed. If your engine has a timing belt and you cannot see the camshaft easily remove the upper bolts to the timing cover and gain visual access to the belt, recheck cam rotation by cranking the engine over. Sometimes a timing belt or chain can jump causing the camshaft to lose correlation with the crankshaft and therefore causing low compression. The best test for this condition is to remove the timing belt/chain cover and inspect timing marks. If the compression is ok proceed to next step.
* Step 5 - Test the ignition system output, ignition systems can vary in configuration but operate on the same principal. Ignition systems can consist of a coil, pick up coil, crank angle sensor, cam angle sensor, spark plugs, spark plug wires, distributor cap, ignition rotor and a distributor and any variations of these components. An ignition coil is a voltage stepper coil that transforms a low voltage (12 volts) signal into tens of thousands of volts needed to jump the gap of the spark plug. This coil is activated by an ignition module triggered by using the camshaft/crankshaft angle sensor; timing is adjusted by the ECM (computer).

Hope helps (remember rated and comment this).

Aug 11, 2010 | 1999 Chevrolet Blazer

1 Answer

04 Sante Fe 2.4L no spark no rpm pulse


rpm is regulated by the crank position sensor in all hyundai cars did one today

Sep 04, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...