Question about 2006 Citroen Berlingo 1.4i

Open Question

Hi having trouble lifting the bonet , the catch on the pessenger side has come loose just wondering how to fix please

The catch has came loose

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hood catch release cable become undone and cannot open the bonet. please help

by using a long lever and looking up from underneath see if you can push the latch to release the bonnet. To make the job easier you may need some one to push down on the bonnet at the same time to release the load on the latch

Jan 03, 2014 | Cars & Trucks

1 Answer

2000 Ford Fiesta Zetec S. The leaver under the stearing wheel which opens the bonet has broken.

should be a cable attached to it push it back into the dash and try closing it

Dec 19, 2012 | Cars & Trucks

1 Answer

How do I remove the passenger side door panel from a 1994 Chevy S10 pickup??

hi there

there will be phillips screw on outside of door panel and usually one where handle is once removed all of them you pull pull gently and there will be pastic rivet clips that you have to get loose once all are loose lift upward and remove from door have a wonderful day thank you

Aug 22, 2011 | Chevrolet S 10 Cars & Trucks

2 Answers

Water Leaking onto drivers side floor

There is a gap/hole, u can see it from the front with ur bonet open or the leak underneath the grill (screw fastened) between the windscreen n the bonet, u can fix it with some bitumen putty, silicon or some of those strong glues. Good luck.

Jun 20, 2011 | 2005 Ford Taurus

1 Answer

Bonet is stuck, put the key in turn it left and its not opening,

Look into the grill at the top you will find the bottom of 6 plastic screws, 4 you get two via the grill slots use a chisel and cut them off, Then one either end of the grill. Place the chisel between two plastic layers, gently lift , check and cut, one each end.
With a wiggle that's the top loose, There are two clips holding the bottom in place Put your fingers through the bottom slot in the grill, push down clip and greatly pull the grill, do both sides, It won't come right out but your aim to loosen it., The lock is held in place in a sleeve with a plastic clips each side, you have push the barrel with a suitable item, this is to push it out of the sleeve and out of its housing, It may need a tap!!
Gently wiggle and pull the grill off
The lock is a 'lock barrel along a shaft to a white plastic coupling' this fits in to the 'bonnet lock'
The security is at the coupling to bonnet lock in the form of a cross shaped plastic key
The key is fitted and held in place in the coupling, and when installed it's fitted in to the lock, and once it's in the lock part it will not come out, so therefore any jolt, pull, movement dislodges the plastic key from the coupling side and due to its design it will not slot back in so the lock barrel just rotates
To open you have to apply pressure on the shaft towards the left and into the coupling and turn the key in the lock barrel at the same time in a aim to get the coupling to catch the plastic key (take a few minutes) but it opens in the end if this is the fault, (alternatively remove the two bolts that hold the bonnet catch to the bonnet)
Once bonnet open remove the bonnet lock mechanism, then with draw the lock barrel, shaft, coupling, By looking in side you will understand regarding the cross key
Anyway you need to remove one of the catches from the side of the plastic key This way it will fit back in to coupling.

Mar 09, 2011 | 2006 Ford Focus

1 Answer

I have a 2007 subaru legacy. it has 17000 miles im having a problem with heating.. when i turn the heat on only driver side blows hot. the pessenger side blows cold even when i turn it on to the winshield...

The air is mixed and routed inside the dash by some flaps. In your case the flap that regulates the mixing of hot and cold air for the passenger side is broken or stuck in the cold position.
The only way to fix that is to remove the dash , access the air system and fix the flap.

Feb 07, 2011 | 2007 Subaru Legacy 2.5i SE Sedan

2 Answers

Electric window doesn't work on 2003 Toyota Corolla

try cheap fix first,replace window control panel switch first/junk yard $5-$10 while their price on driver side if cheap enough replace pessenger also..

Apr 19, 2010 | 2003 Toyota Corolla

1 Answer

Bonnet releases from in the car, but second black catch is loose.

You will see a black hook with a hole in it on the right side of the hood´s snaparm (looking direction). Push the black hook right, and you will be able to lift the hood.

Sep 19, 2009 | 2003 Volkswagen Passat

2 Answers

Hi my double seat on my hyundai santa fe won't go down

there might be an interior panel not clipped in all the way at some spot, gently beat on the bottom edge and top edges of all the trim surrounding the mounting brackets, also the catch might not have been placed correctly during assembly. No idea why but I had 2 hyundai's and a Kia Magentis/optima (suprisingly nice for a kia...) with loose body trim or a trunk catch not quite right (yay seeing one side of the hood lift and shake when you're cruising the roads). Just take a good luck at what you can s3ee, gently tap on the plastic trim edges, and maybe see the dealer about reinstalling the catch (usually free)

Aug 20, 2009 | 2006 Hyundai Santa Fe

1 Answer

Engine Under The Bonet

the Motor is in the Front on these Cars. Please Rate My Response! Thanks!

Jan 31, 2009 | 1999 Hyundai Accent

Not finding what you are looking for?
2006 Citroen Berlingo 1.4i Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides