Question about Cars & Trucks

1 Answer

Trying to remove the front diff on a x240 great wall so the sump can be removed

Poor factory seal on the sump trying to remove without taking the motor out

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 45,551 Answers

Look around the diff and you will see where it is mounted to the chassis/subframe place a mobile jack under the diff and remove those mount bolts. Lower the diff down enough to get the sump pan off.

Posted on Nov 30, 2014

  • robert richards
    robert richards Nov 30, 2014

    thanks heaps had to lift the motor up as well also had to remove the oil pick line before the sump could be removed

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a 2006 jeep grand Cherokee front diff


no engine stated? size, cylinder count?
this is covered in the FSM, book
the factory service manual.
id bet pulling the engine is more easy. (for sure the 4L)
id did this, one time by jacking up the engine, mounts pulled.
(on a bet) and removed pan. 4.0L inline 6 .
to get pan free , had to pull the pump blindly! (hard trick)

now the book the WK jeep (05 up)
its all here. for free, (I have the pay for links too, ask)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see front axle/diff, R&R

Jul 20, 2015 | 2006 Jeep Grand Cherokee

1 Answer

How to replace front differential seal on 2007 4.7 toyota tundra


This is not easy....You will need air tools ,spray penetrate,seal remover,hammer,and Jack stands..Seal installation tool,.All proper tools..safety glasses.correct seal replacement.,new lock nut...Set park brake,block rear wheels,raise vehicle front and safely place jack stands under each side of lower control arms..Spray lube front drive shaft mounting hardware and lock nut that holds Yoke on front diff..Let it set to penetrate..put vehicle in neutral..Mark shaft to yoke location and direction perfectly because it has to be installed in perfect timing exactly how it was removed..,Remove drive shaft..Remove lock nut and yoke from front diff...You will have to hold yoke while removing lock nut because it will spin..PROTECT HANDS..( These can be VERY DIFFICULT to remove..Sometimes they have to be heated..You will need a yoke removal tool if it doesn't tap off with hammer...Mark exactly the yoke to spline location before removal..You can take close up photos however Mark it also to be sure...If you re-install it wrong it will vibrate terribly..Once yoke is removed You can remove seal.Make sure the new seal is correct...CAREFULLY..DO NOT DAMAGE SPLINES WHILE REMOVING..Sometimes even the perfect seal remover will damage splines..So cover it to protect spline threads..Clean all areas once seal is removed..Make sure nothing is pitted or damaged...Install new seal with installation tool..Lightly,perfectly tap it flush with diff..You can use old seal to install new seal if you don't have installation tool But only a pro should do that...Once in place Line drive shaft yoke with your marks and tap it on ..Use NEW LOCKNUT AND TORQUE IT TO SPEC..Install drive shaft as marked..torque to spec..Lower truck and check fluid..Complete..

Dec 13, 2014 | Toyota Cars & Trucks

1 Answer

How do i replace the headlights on a great wall x240


great wall x240?
this
The Great Wall Haval H3 (Chinese: ; pinyin: Changcheng Hafu), also known as the Great Wall Hover, is a compact sports utility vehicle (SUV) produced by the Chinese manufacturer Great Wall Motors since 2005.

unscrew lamp , replace. if it has Euro style lamps.
easy huh?

Oct 12, 2013 | Cars & Trucks

1 Answer

Need to replace oil pan on a bmw 2004 330ci


Raise engine with special tool 00 0 200 approx. 5 mm.
- Remove suction filter housing. Remove engine splash guard.
- Drain engine oil. On vehicles with automatic transmission:
- Disconnect oil lines from automatic transmission and from oil pan.
- Release guide tube for dipstick.

Note: M52TU and M54 only.
- Detach return hose from cyclone oil separator on oil dipstick guide tube.
- Replace O-ring.
- Remove front end reinforcement.
- Detach steeling spindle from steering gear.
- Remove vane pump for power steering unit (lines remain connected).
- Disconnect plug connection to oil level sensor.
- Loosen top and unfasten bottom of left and right engine mounts.

E46 4WD only
- Remove left and right swivel bearings.
- Remove output shafts. Remove front propeller shaft.
- Remove front axle differential.
- Detach brackets for left and right control arms from engine carrier.
- Release retaining brackets for left and right stabilizer bars.
- Unfasten screw connection on front axle support and lower the front axle support.

Note: There is no need to detach the steering gear from the front axle support.

- Unfasten oil sump screws at transmission and engine ends.
- Lower and remove oil sump.
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agent to the area around seams.

Installation:
  1. Replace gasket
  2. Install oil sump.
  3. Insert all oil sump screws.
  4. Insert screws in transmission end without preload at this stage.
  5. Tighten down screws in engine end.
  6. Tighten down screws in transmission end.

E60 Removing And Installing, Sealing Or Replacing Oil Sump (M54)

Necessary preliminary tasks. -
- Remove intake filter housing
- Remove guide tube for oil dipstick
- Lowering front axle support
- Drain off engine oil
- Disconnect plug connection to oil level sensor.

On vehicles with automatic transmission:
- Detach oil lines from automatic transmission and from oil pan.
- Unfasten oil pan screws at transmission and engine ends.
- Lower and remove oil pan.

Installation:
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agen to the area around seams.

Installation:

  1. Replace seal.
  2. Install oil sump.
  3. Insert all screws on transmission end, without preload at this stage.
  1. Tighten down screws on engine end.
  2. Tighten screws on transmission end.

Or take it to a dealer....

Apr 19, 2011 | BMW 330 Cars & Trucks

1 Answer

Canot get pan out with motor jack up into fire wall not able to clear dual oil pickups front and rear sumps over front diff f 250 4x4 5.8 gas motor


you must unbolt the oil pump pick up in order to remove pan. are you just replacing a gasket due to a leak?? I usually end up dropping the pan at the point where you have it and plutting in the gasket there. Pain in the but but easier than taking the pan down. Make sure you use a rubber gaske t(not cork) and apply a dab of silicone in the corners by the front and rear seals when putting back together.

Feb 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Front crankshaft seal, 1989 hilux


Hello,

Yes, it's possible to change the seal after removing the balancer.
If the balancer shows signs of scratching, wear at the place of the seal, change that part too!

To remove the old seal, drill 2 small opposite holes in the seal flange ( there is metal in it ).
Screw 2 (parker) screws in the holes, so you can pull the seal out gently.
Grease the new seals' inner race, and put some sealant paste to the external race.
Push it back in place with a wooden piece ( drill a hole in the center for the crankshaft end )
Grease the outher race of the balancer. This will help the seal come gently into place.

Good luck!

Nov 01, 2009 | 1989 Toyota 4Runner

1 Answer

Front diff oil leak


remove entire trans,remove 8 bolts and then remove front differential case at this time you will need to remove torque convertor with tube do not remove this tube from the convertor it drive the oil pump, the gasket is liquid gasket make sure surface is clean,also at this time replace torque convertor seal and seal tube this tube seperates transmission fluid from gear oil good luck

Aug 13, 2009 | 2001 Subaru Forester

1 Answer

2002 Jaguar X-Type Oil Pan Gasket replacement


have you smashed the sump ??never seen one leak yet?? sure its not the front or rear end oil seals ??..sounds like you have the sub frame in the way ,evan if you remove this bolt you will not be able to drop the sump without removing or lowering the sub frame assembly as the oil pick up pipe stops you from removing the sump in situe.Its not difficult to drop sub frame just time consuming

Jan 01, 2009 | 2002 Jaguar X-Type

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...