Question about 2010 Dodge Caliber

1 Answer

Hello,thanks for the help on my calibre.a small red light(like a dot)appears in the bottom of the gauge cluster(again car won't start).is this a disable?should I disconnect the neg. terminal and re-install?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 4,977 Answers

This light is usually an indication that the security system has been activated and won`t allow the car to start. it will have to be reset. disconnecting the battery will not turn off the anti-theft as it will indicate the car is being stolen. did you use the proper key to start it when this happened. it could also be a problem in the BCM.

Posted on Nov 30, 2014

  • Anonymous Nov 25, 2015

    this is how go to your driver side inner fender first make sure you turn you r steering wheel all the way to the right now go back to your driverside in fender well remove the plastic guard from that the part facing the bumper now look up inside and remove the the negative post off your battery leaving it un-hooked for about 15 to 20 minutes now hook it back up just remember not to lock the power door locks with remote or with the lock switch its ok when when driving just remember to lock the doors after everyone else is out while the car is running then it just you in the vehicle with the engine running now lock all doors with the lock switch while the engine is still running now shut engine off take the key out open your driverside door by using door handle now manually push down driverside door lock knob remember to do this ever time or our alarm will be enabled again then you have to unhook the batterry again to go through the procedure again to disabling the alarm system again well have fun this works for me!!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After disconnect and reconnect the battery of my opel antara, the indication of odometer displays only 888... for all indications. How can i reset it?


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2007 Opel Antara 2.0

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

1 Answer

Trying to locate electrical junction to test fuel level sensor


Fuel Level Indication System The fuel level indication system is a magnetic gauge system. It consists of a magnetic fuel gauge (9280) mounted in the instrument cluster (10849) and a sending unit located in the fuel tank (9002) with an instrument cluster gauge amplifier (10E849) in series between the two. No instrument voltage regulator is used with this system. Fuel Gauge
The magnetic gauge movement consists of three primary coils, one of which is wound at a 90-degree angle to the other two. The coils form a magnetic field which varies in direction according to the variable resistance of the sender unit which is connected between two of them. A primary magnet, to which a shaft and pointer are attached, rotates to align to this primary field, resulting in pointer position. The bobbin/coil assembly is pressed into a metal housing which has two holes for dial mounting. There is no adjustment, calibration or maintenance required for these gauges. The instrument cluster amplifier is calibrated to the fuel gauge. The instrument cluster amplifier and fuel gauge must be replaced as a system. Instrument Cluster Gauge Amplifier/Check Gauge Module
The instrument cluster gauge amplifier electrically averages fuel sender readings so the fuel gauge displays actual fuel level and not fluctuations due to sloshing in fuel tank. The instrument cluster gauge amplifier is a small printed circuit board which latches into a pocket on the back of the instrument cluster. The electrical connections for ignition, ground, input from fuel sender and output to fuel gauge are made through a spring-type connector on the instrument cluster gauge amplifier to the instrument cluster printed circuit (10K843) on the instrument cluster. There are no provisions for calibration or adjustment of the instrument cluster gauge amplifier.
Fuel Sending Unit
The fuel sending unit consists of a variable screened resistor made up of a ceramic substrate. It is controlled by the action of an attached float in the fuel tank. When the fuel level is low, resistance in the sending unit is low. When the fuel level is high, the resistance in the sending unit is high. As the float moves from empty to full, the resistance will gradually and continuously increase. f9e3b50.gif

Mar 10, 2010 | 1997 Ford Ranger SuperCab

3 Answers

Gauges on 2005 ford mustang not working


If you can solder or know someone who can this is an easy fix. 1st the problem...The Mustang gauges are small DC motors, the motors are going bad. I just completed this on my wifes 2005 Mustang. Go to Ebay and do a search for Mustang stepper motors. They will run you about $8 each. do them all while the cluster is out.I used David Ruberg (www.speedometerrepairguy.com). Pull of the housing around the inst. cluster, take 4 screws out that hold the cluster in place. pop off the connector, take it into the house and solder in the motors. David includes instructions with the order. It took me about 2 hours total.

Sep 14, 2009 | 2005 Ford Mustang

4 Answers

Instrument panel went dead


Checked Every fuse in the fuse box (no small task).This includes #4 - Power point Instrument Panel, #14 - Day time running lamps (auto lamps doesn't work nor does auto lock), #27 - ignition switch run feed, #35 - Instrument Cluster, #41 - Instrument Cluster, #42 - Delayed Accessory, #45 - Ignition switch run/start feed, #102 - Door locks body security module, #103 - Ignition switch, #110 - Ignition switch, & #116 - Ignition switch. But I also check all other ones as well, they all register OK. AC panel & radio work. Turn signals work. Mileage does not work, trip computer does. So, basically, everything works except auto head-lights, auto locks, and the dash cluster (no MPH, RPM, mileage display, Fuel, Temp, Tran Temp, and Oil Pressure).

Aug 19, 2009 | 2003 Ford Excursion

1 Answer

1996 Dodge Neon - All dash gauges work intermittently


The problem is broken solder connections on the instrument panel circuit board. Now here's how to fix it: Lift up & remove dash pad/gauge cluster trim. Remove 4 phillips screws to remove gauge cluster. Turn gauge cluster over, remove 6 T15 Torx screws, & remove black paper. Remove 5 more T15 screws for the circuit board & 4 T15 screws at the wiring harness connectors. Disconnect the gray odometer cable; just push in the little pin and slide it out. After all the screws are out, gently lift up on the circuit board; you may need to lift up on one side at a time. BE VERY CAREFUL! After you remove the circuit board, flip it over (you will see the dash lights). There are two areas with 10 soldered pins (two rows of 5 pins) & a black dot above & below it. If you look at these pins closely, you may see the broken solder. Apply heat from a soldering iron to these pins; you shouldn't have to add more solder, but you may. As it heats, the old solder will become shiny & melt. Remove heat. This should be enough to repair those connections. Look at the solered pin; if you see a crack in the solder around the pin, heat it up again & apply a small amount of solder. After you reheat/resolder those pins, let it cool. Then reassemble the gauge cluster. It sounds tougher than it really is. Just be gentle & work carefully. You'll be fine, & your gauges will work again.

Mar 14, 2009 | 1996 Dodge Neon

1 Answer

95 saab 900 turb0 gauge cluster works intermetanly


I have this problem too and my new Saab mechanic told me that I would probably need a new instrument cluster. He said a brand new one costs $2500 but that he would order me a used one from a car that had fewer miles than mine as you can set them back but not forward. He both diagnosed and temporarily "fixed" the problem by slamming his hand really hard on the dash over the panel and all the lights and gauges immediately started working fine....for now. I haven't had the work done yet (I have a 1998 Saab 900S with 130K) so if anyone has any other ideas about this I would love to know what they are. This issue with the gauges and dash lights has been happening on and off for over a YEAR and this is the first time someone has had any idea what it is. I already had my ignition switched replaced so we know that's not what it was. THANKS

Feb 12, 2009 | 1995 Saab 900

1 Answer

Nissan pulsar n13 fautly water temp gauge


Switch ig. on, ground the sender unit wire for about 3 seconds see if the temp. gauge moves, if so change sender unit, if not then it is a faulty gauge reader.also check instrument voltage stabilizer.

Dec 23, 2008 | 1988 Nissan Pulsar

3 Answers

1997 CE Lancer speedometer


i had the same problem on my g/f's 2000 lancer GLXi, (with tacho),
i fixed the problem by putting a jump wire on the back of the instrument cluster,
the fault was in the wiring to the tacho part & i drew up my own wiring diagrams for the cluster unit,
then traced the fault,
looking @ the back of the cluster unit, the top right hand screw for the speedometer,,, follow the track on the circuit-board, there is a link wire UNDER the board (there is a dotted line on top where it goes, i think its the left 1,,, there is 2) this track then goes to the bottom left screw on the tacho,,,
i soldered a small gauge wire from the bottom of the link solder joint (MAKE SURE ITS THE CORRECT LINK, THERE IS 2 SIDE BY SIDE) to the bottom right track on the vertical plug socket (its common pos for the warning lights) this is where the "MIRAGE" & other "CE LANCER" (without tacho) gets its speedometer & gauges power from,

kind regards waz
if anyone needs a photo i will pull out the dash again lol its only 6 screws

Jul 17, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2010 Dodge Caliber Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...