Question about Cars & Trucks

1 Answer

Front axle nut size

Do not have the right tool

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 181 Answers

O'reilly auto parts has loan a tool. They can tell you what size you need.

Posted on Nov 30, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: front rotor nut

hi out of curiosity? are wanting to renew thebrake disc/rotor ? or the actual hub that rotor fits to ? as not usually necessary to have to remove hub to change rotor ? unless the rotor is bolted to hub from the rear ?

Posted on Nov 08, 2008

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

  • 1 Answer

SOURCE: need the axle nut size for the front drivers side

Our is a 44mm socket size........thought i would post it, since the above was stupid and didn't....can't find one in town.

Posted on Jun 26, 2009

  • 14036 Answers

SOURCE: front wheel bearing assembly unit, what tools will

TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Posted on Mar 17, 2010

  • 1 Answer

SOURCE: what size socket fits the front axle nut on a 2003

For a 2002 Escape the hub nut is 32 mm. The torque specification is around 175 ft.-lbs.

Posted on Jul 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size socket do i need to fit axle nut on a 2007 dodge caliber?


I told you already 22mm. It was a guess, but it was right!!

http://www.oreillyauto.com/site/c/search/Spindle!s!Axle+Nut/01232/C0362.oap?year=2007&make=Dodge&model=Caliber&vi=1433273

Dodge Caliber 2007, Front Spindle Nut by Dorman®. Thread Size: M22-1.5. Packaging Quantity: 5. Packaging Type: Box. Dorman's Spindle Nut is manufactured for high corrosion resistance and a long service life. Depending on the...Direct replacement for a proper fit every timeHigh quality steel construction more details on -
https://www.carid.com/2007-dodge-caliber-driveline-axles/dorman-spindle-nut-31531756.html


axle nut on 2007 dodge caliber Google Search

Jan 22, 2017 | Dodge Caliber Cars & Trucks

1 Answer

What size axle nut for 2000ford taurus se


Axle nut size? - Taurus Car Club of America : Ford Taurus Forum

www.taurusclub.com > ... > Suspension, Handling and Brakes
Jul 23, 2011 - 8 posts - ‎5 authors 1996 Mercury Sable front axle nut. I have read that the size is 30mm but the socket that I rented (30mm in a ... 2000 Duratec SE White Wagon Axle nut torque question. - Taurus Car Club of America ...
11 posts
May 4, 2012
CV Axle nut size
11 posts
Dec 9, 2011
Why Does The Axle Nut Need Such A Big Torque
11 posts
Dec 7, 2009
2000 Ford Taurus Front Wheel Bearing And Half-axle ...
11 posts
Apr 18, 2009
More results from www.taurusclub.com

Sep 28, 2015 | Cars & Trucks

1 Answer

Front axle nuts size for 2003 pontiac grand prix


2002 Grand Prix front axel nut holding on hub is a 33MM or 1 5/16 deep socket

Feb 08, 2012 | 2003 Pontiac Grand Prix

2 Answers

Replacing front hub assembly


remove the wheel, then remove the caliper and tie of to the side, slide rotor off, remove the axle nut, remove the lower balljiont nut, use a balljoint sperater tool to break balljoint free from spindle, using a long pry bar pull down on lower control arm to remove from spindle, pull spindle out to pull axle out of spindle, next tie spindle out of the way of axle, use a pry bar in between rear axle joint and trany give a pull to break free from trany and pull out. reverse to install. hope this helps.

Sep 04, 2010 | 2001 Chevrolet Blazer

1 Answer

Front wheel bearing assembly unit, what tools will i need? size sockets ext the right foot lbs of torque for the axel nut,


TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Mar 16, 2010 | 1999 Oldsmobile Alero

1 Answer

Replacing the right wheel bearing how do u remove that hub do u need a special tool for it


is it a 4x4? the wheel bearing comes with a new hub assembley . Just find out what size the front half shaft nut/ lock nut/axle nut- is. its probably a 33mm thats the only special tool you will need. Unscrew it, take your outer tie rod off the spindle/steering knuckle, theres 3 bolts behind it, take them off then disconect the abs harness and pry out the old hub assembley use a rubber hammer (dead blow hammer) to tap the half shaft out if seized. when installing the new wheel bearing see your manufacturer specs. for torquing the axle nut back on.

Feb 16, 2010 | 2001 GMC Jimmy

1 Answer

When you replace front wheel bearing on dodge ram 1500 4x4 is their a toqure spec for the axel nut


175 ft pounds for the axl nut it gona take alot to get it of.the nut size is 1 -11/16. air tools make it easy the hub to nuckle nuts are 14mm 12 point.

Dec 30, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

How do I remove and replace the front axle?


you first need to remove the big nut that is holding the wheel on the side that you are trying to replace first you must buy the right sized socket thet will fit the nut the while the vehicle is still on the ground take the hub cap off and the cater pin out and then put the socket on the nut using a halt inch tourge ratchet loosen and remove the nut then jack your vehicle up and remove the wheel and the bolts that are holdung the hub and then with a pickle fork that is the tool used for removing tie rod ends that is connected to your stirring and then after that remove your axle and then reverse the procces to put ti back together.

Sep 10, 2009 | 2000 Suzuki Grand Vitara

2 Answers

Need the axle nut size for the front drivers side for a 2004 dodge 2500 4x4


Our is a 44mm socket size........thought i would post it, since the above was stupid and didn't....can't find one in town.

Mar 21, 2009 | 2004 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...