Question about Cars & Trucks

1 Answer

How do I get replacement bulbs for my Kirkland tree?

Clear lights replacement bulbs

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 44 Answers

Try .....batteries n bulbs.com

Posted on Dec 01, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All the lights in my Pontiac g6 work except my interior lights and the fuse is good. Also my fog lights don't work either and the fuse is good.any suggestions


yes check all the bulbs and the fog lights one blown bulb could knock it all out kinda like in a Christmas tree one bulb goes out the whole line goes out

Feb 25, 2015 | 2005 Pontiac G6

1 Answer

I need the plug - in configuration for my Kirkland 7'; tree Item Number 894039 purchased at Costco


As I understand it they have a life time warranty on that tree but removing the strands may void the warranty. Take it back to Costco and see what they say.

Dec 06, 2014 | Cars & Trucks

1 Answer

No signal no hazzards


start with checking all the bulbs its the least expensive to start with. Most cars lights stop working when one of the bulbs go out, almost like christmas tree lights, if your bulbs are good then the signal switch needs looked at as most cars after 1984 the switch is wired with the hazard button.

Jul 08, 2012 | 2006 Pontiac Torrent

1 Answer

I bought a target pre-lit christmas tree but half of it wont light up even though its all plugged.How do we fix it?


trystarting from the point that bulbs aren't working,take one of the replacement bulbs that usually come with the lights and replace them one at a time.just one replacement bulb to start then the one you took out put it in the next until either it lights up or you reach the last unlit bulb,but hopefully you dont get to the end because if you do then there's more then one bulb thats faulty. I've had that happen alot so dont give up..If the lights are on two separate wiring check for a glass fuse hidden on either ends of plug(wall or tree) I hop that helps.

Dec 03, 2011 | Cars & Trucks

1 Answer

Rear turn signal electrical


Try changing the bulb. If that doesn't work, then your going to have to rewire or replace the socket. You can get a replacement at any parts store, or you should be able to get one from the dealership if you want OEM. If the bulb socket is part of the tail light housing then your best bet is to get one from a salvage yard unless you want to spend the money for a new one.

Jul 21, 2009 | 1999 Chevrolet Venture

3 Answers

2003 Hyundai Elantra Instrument panel light burned out


There are 3 little bulbs on the back of that cluster. They are easily replaced providing you can source the bulbs. There are 2 white ones - one on each end. And a green one that goes behind the A/C button. To access this cluster, remove the ash tray to reveal 2 phillips screws. Remove these and set aside. Next, in the gauge cluster over the steering wheel, there are also 2 or 3 phillips screws. These are in the top. Remove and set aside (duh). Now, starting near the ash tray, begin tugging the dash. It *should* start to come loose. It will makes some noise, but its pretty sturdy.

Keep in mind there are a few wire harnesses attached. Don't go all He-Man on it. These harnesses are easily disconnected and reconnected if you unclip them the way they are intended.

You should now be able to see the heater AC cluster. There are a few philips screws around it. Remove them. Pull out the cluster and rotate it around to reveal the back side. There you will see a little round disc with a slot in it. The slot may be painted or highlighted with red. With a small slotted screw driver, give this little disc a GENTLE quarter turn. You should then have your culprit bulbs in hand. They resemble Christmas tree lights!

It seems that these bulbs are hard to find and are most likely dealer only parts. I have seen some LED replacements in a few places online that may work, but I would prefer something of the OEM variety.

May 22, 2009 | Hyundai Motor 2003 Elantra

2 Answers

AUDI A4


It's likely similar to my 99. Pull back the carpeting in the trunk behind the light, and you'll see a plastic tray mounted vertically with a harness plugged into it. That's the "bulb tree" as it's called. Pop that out, remove the blown bulb, install a new one, and then snap the tree back in place, and you should be good to go.

Sep 28, 2008 | 2005 Audi A4

1 Answer

Lights


Go into the trunk and pull back the lining - you'll have access to the bulb tree from there.

Jul 31, 2008 | 2003 Audi A4 Cabriolet

1 Answer

I have a UK registed, Feb 2000 AUDI A6 2.7T QUATTRO AUTO ESTATE, Is it right that these are fitted with just one rear fog light that operates and the other is just for show.


Yes it's true. What I did on my US-spec A4 is to pull back the trunk lining on the passenger (right) side, where there is no functional foglight (my rear fog from the factory is on the left side). What I found was that the "bulb tree" has a fully powered socket for a bulb that would fit into a rear foglight on that side, but no bulb was installed. The part of the taillamp that would have a hole for such a fog bulb had a **** instead. I used a drill to widen the **** into a hole large enough for a bulb, and installed a bulb in the bulb tree, and voila - dual rear fogs:)

Jul 21, 2008 | Audi A6 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...