Question about Mitsubishi Cars & Trucks

1 Answer

Where is crank sensor on mitsubishi colt - Mitsubishi Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Filmmaker:

    Uploaded 5 video answers.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

Nick, this is mostly an educated guess, Mitsubishi made so many engines, dependent and model and geography. But, MOST are located on the front of the engine(where the belt is) under or near the water pump. Access is from beneath the car. The other location, although unlikely, would be on the bell housing next to the engine. Helpful Hint>>>Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. before replacing any parts, recharge or replaced battery.

Posted on Nov 29, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank sensor on 2005 mitsubishi colt


If it is the 2.4l engine, here is a link with some pics and a procedure for testing it.
http://easyautodiagnostics.com/mitsubishi/2.4L/ignition-coil-and-crank-sensor-tests-1

Nov 29, 2014 | Mitsubishi Cars & Trucks

1 Answer

My mitsubishi 2800TDi diesel engine wont start


several possibilities
battery to low to spin the engine fast enough
sir in the system. electronic stop keeps the fuel shut off.
immobiliser not operational. can/crank position sensor problems. broken timing belt
glo-plugs not working
run the fault codes to see if any sensors are recorded.

Jun 05, 2014 | 2007 Mitsubishi Colt 2000

1 Answer

I have a mitsubishi colt, and it has problems starting in the mornings. It turns over, but wont start, when I eventually get it started its very lumpy, and when I push the accellerator the engine almost...


There is no simple answer, there are to many variables. If you have access to a scan tool, pulling the codes should help. Without them its back to old school hunt and peck method. At this point we need to narrow down the problem. You need to test for spark.
  1. Tag and disconnect the spark plug wires from the spark plugs.
  2. Remove the spark plugs and install the spark plug wires to each spark plug.
  3. Ground (do not hold spark plug) the spark plug; check if spark occurs while engine is being cranked.
Crank the engine for no more than 2 seconds at a time to prevent flooding the engine with gasoline.
If you have spark, You will want to make sure you have fuel injector pulse, along with fuel pressure. If you have spark ..simply spray some starting fluid in through the air filter and hold the gas pedal to the floor and crank it over while spraying. If it fires up, you know it is fuel related( fuel pump, regulator, or ECM if no injector pulse) . If you have no spark then look at ignition coil connection and trace through to the distributor( if equipped ). The crank shaft sensor has a tendency to fail on these as well. This should give you a few things to test and check to start you on your way to narrowing it down. If you have no spark then look at ignition coil connection for power and trace through to the distributor( if equipped ). If it is DIS( no distributor). It may be the Crank sensor or the ECU. The crank shaft sensor has a tendency to fail on these as well.
The ECU uses the signal sent from the Crank sensor to trigger the spark and fuel injectors. ( make certain you have checked all fuses)

Apr 06, 2011 | 2006 Mitsubishi Colt

1 Answer

THE CAMBELT ON MY 2006 COLT 2 litre LDV HAS BROKEN WHILE IDLING. WILL THERE BE DAMAGE TO THE ENGINE?


Most multi-valve engines suffer damage when a cam belt snaps I am afraid to say..however about 1 in 100 don't so I hope yours is the 100th. Good luck.
On NO account attempt to crank the engine or further damage will occur.

Dec 05, 2010 | 2006 Mitsubishi Colt

1 Answer

How to make remote key for Mitsubishi colt 2006?


do you have a remote key at all?
if yes then you can take the key go to a keymaker shop and thei will be able to clone the key code and duplicate a new remote key for you.

Oct 31, 2009 | 2006 Mitsubishi Colt

1 Answer

P code


P1936 is a Clutch Switch/ Sensor Signal problem.
Hope this helps you solve the problem. 

Apr 22, 2009 | 2006 Mitsubishi Colt

2 Answers

55 plate colt


The sensor is behind the bumper reinforcement panel.

Mar 27, 2009 | 2006 Mitsubishi Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...