Question about 1996 Chrysler Town & Country

2 Answers

How do I fix my van when its not firing?

Replacing the spark plugs

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 36 Answers

First thing to doo remove spark plugs check if engine has good compression in each cylinder above 130 psi is ok. next remove oil filler cap have assistant crank engine see if rocker arms move while engine turning over. If comp low maybe internal problems.If arms not moving while cranking possible timing belt poblems if it has one. Hope this is of some use.

Posted on Nov 29, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 97 Answers

Cranks but won't start? Replacing the plugs won't be the fix most likely. You are probably looking at the components that control spark. Make sure that everything is dry ( condensation is a huge factor for things like this )

If you are having this problem AFTER replacing the plugs, then you are going to want to make doubly sure that you put the wires in the proper places. Don't crank the engine over like this very long, or you will dump raw fuel into the catalytic converter and could ruin it, which will cost you more than you'd probably want to sink into that van.

Posted on Nov 29, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No fire to the spark plugs


For spark plug problem,click the help links provided below :---Car has no spark?http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html
------------How to Replace Spark Plugs?http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html
-------------Car cranks, has spark but will not start?

http://howtobyme.blogspot.com/2011/12/car-crankshas-spark-but-will-not-start.html

------------------------
The spark plug firing order for car?http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html
----------How to gap spark plug ?http://technoanswers.blogspot.in/2012/02/how-to-gap-spark-plug-on-chevy-impala.html-----------Spark plug Replacing for?http://technoanswers.blogspot.in/2012/02/spark-plug-replacing-for-chevy-impala.html
-----------How to identify number one spark plug on the distributor cap?http://schematicsdiagram.blogspot.com/2011/12/how-to-identify-number-one-spark-plug.html
---------How does the spark plug wire go on the distributor cap?http://schematicsdiagram.blogspot.com/2011/12/how-does-spark-plug-wires-go-on.html
---------Spark plug Firing Order Diagram?http://schematicsdiagram.blogspot.com/2011/12/2006-suzuki-forenza-spark-plug-firing.html
-----------This will help.Thanks.

Feb 23, 2012 | 1993 Honda Accord

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Stalling out


sound like the spark plugs arent firing hot. try replacing them, if still a problem it could be distributor. start with plugs, they are cheaper

Dec 28, 2008 | 2001 Chevrolet Silverado 1500

1 Answer

Van is getting gas and fire but will not start.


maybe its the ignision fuse your van will do all the starting signs but if this fuse has gone it wont run

Oct 19, 2008 | 1994 Chevrolet Astro

Not finding what you are looking for?
1996 Chrysler Town & Country Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...