Question about Cars & Trucks

1 Answer

I took the side pan off my 1999 626 lx 2.0 there is no filter in it could any body tell me where it is

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Cars & Trucks Expert
  • 226 Answers

You took the bottom pan out, sorry it is the side pan and good luck with that

Posted on Nov 28, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77186 Answers

SOURCE: Where is trans filter?

The transmission filter in your vehicle is inside the transmission. It requires transmission removal and overhaul to be replaced.

The transmission filter in your vehicle does not need to be replaced unless the transmission is being rebuilt.

Posted on Oct 03, 2008

  • 1509 Answers

SOURCE: Found the transmission, but having trouble

Your not doing a job you should do without the manuuel and a good friend that knows whats going on. why are you doing this to begin with? Most cars since the eary 90's go to the junkyard with good trans and no service has ever been done

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can not get new trans filter to slide into the hole in the valve body. seams like the new rubber seal is to big.. took out the old seal..what can i do. 03 ford windstar lx


Insure that you have the correct part and use wooden dowel just larger than seal if needed to drive it into place. This should not require much effort if you have the correct part.

Jan 21, 2015 | Ford Cars & Trucks

1 Answer

1990 ford ranger 4x4 4.0 had transmissoin overhaul shifted fine at first next day wont shift out if first to second


It is very important to change the filter in the pan, at the valve body, even if you have an inline magnetic filter for the ATF and I will tell you why.

My transmission mechanic Gaby, at Jul's Transmission in Hollywood, Ca. showed me last week a 2005 Ford Expedition 4wd automatic transmission's pan filter that was completely plugged/blocked, where the owner had installed an aftermarket drain plug in the transmission oil pan so that he could do regular ATF fluid changes to keep his transmission running longer.

He did not drop the transmission pan and change the filter inside at anytime. All he did was kill his ******* sooner by having a plugged up pan filter and the valve body was heavily layered in wear materials from the transmission.... His transmission crapped out at 38,000 miles. His FORD dealer had warned him that prior to installing the drain plug in his transmission oil pan, that his warranty was void on the transmission if he did that.

You're absolutely right about keeping ATF fluid clean and that inline magnetic filter for the transmission from BOSS products sounds like a great idea! I am planning to check it out and install one on my newly rebuilt 4R55E 2wd transmission. Thanks for the tip! :-)

Change the ATF fluid and pan filter and put on a new pan gasket once a year/12,000 miles. If you have a 4x4 (4WD) and do alot of offroading or if you do a lot of towing with your 4x2 (2WD) you should check your ATF even sooner and change as necessary due to it being burned or a high content of worn materials (friction material, metal, etc.) suspended in the ATF oil.

The filter in the pan mounts right at the valve body and also there is a magnet in the pan itself. That is another reason to once a year (or as driving conditions warrant) drop the pan and change the filter and clean the pan magnet.


buy f150 parts.

Jun 03, 2012 | 1990 Ford Ranger SuperCab

1 Answer

I replaced the snap ring and retainer because they were both broke and still no luck with overdrive working


Overdrive would not engage at 35+ mph. Took trans pan off, removed filter, dropped valve body out. Found broken snap ring on overdrive servo. Removed and replaced snap ring. Opened valve body and found 1 of the broken pieces stuck in a valve. Replaced all valve body gaskets. Put valve body back in with 95 in/lbs torque. Put in new filter. Pan on with 120 in/lbs or 10 ft/lbs. Refill with trans fluid. Run through gears. Lower vehicle. Test drive.

Oct 30, 2011 | 2004 Ford F150

1 Answer

How to change transmission filter on a 1997 grand am GT


The filter is located inside the transmission pan. I prefer to do this procedure with the vehicle sitting level up on four jack stands. Position the jack at the lower body flange and at the center of the vehicle towards the front slightly. lift the vehicle in the air high enough to install two jack stands at each end of the body at the lifting pads. lower the vehicle onto the pads. roll the jack under the body and lift the other side up to the same height and place the other two jack stands in the same place on the other side. Place a large pan under the transmission pan and loosen all the pan bolts but do not remove them yet. Fluid will start to run out of the sides of the pan. Slowly loosen the bolts that are farthest away from you while holding the pan with your other hand. Drain more fluid out by slowly lowering the pan with your other hand. Once the fluid has stopped coming out, press the pan back up against the transmission and remove the rest of the bolts. Lower the pan straight down and place it in the drain pan. The filter should now be visible. It will either be held in by a single bolt or press fit into place. This is a messy job so, wear old clothes and always wear safety glasses when performing this procedure.
CAUTION : Use quality jack stands for this procedure. The gasket is usually reusable.

May 17, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

I need to know how to change the transimission filter on a 1996 ford thunderbird v8. Or at lest where to find a diagram on how to do it


Copied from AutoZone.com:


REMOVAL & INSTALLATION


See Figures 1 and 2
  1. Raise and safely support the vehicle on jackstands.
  2. Place a drain pan under the transmission.
  3. Loosen the pan attaching bolts and drain the fluid from the transmission.

Always place used fluids and oils into a sealed storage container and take to an approved recycling collection facility. Never dump used fluids or oils on the ground or in a trash receptacle. Contamination to the environment can and will occur.
  1. When the fluid has drained to the level of the pan flange, remove the remaining pan bolts working from the rear and both sides of the pan to allow it to drop and drain slowly.

Some AOD transmissions will have a plastic plunger type plug floating loosely in the pan when draining the fluid. It is of no importance and was used in the assembly process of the transmission. Discard it before reinstallation of pan.
  1. When all of the fluid has drained, remove the pan and clean it thoroughly. discard the pan gasket. If equipped, remove the pan magnet.




0900c1528006bc40.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the remaining bolts, then remove the transmission fluid pan from the vehicle



0900c1528006bc41.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: On some vehicles, such as this 1995, you must remove and clean the pan magnet
To install:
  1. Place a new gasket on the pan, then install the pan on the transmission. If equipped, don't forget to install the pan magnet. Tighten the pan attaching bolts as follows:

    C3 and C5 Transmissions: 12-16 ft. lbs. (16-22 Nm) A4LD Transmissions: 8-10 ft. lbs. (11-13.5 Nm) AOD Transmissions: 71-119 inch lbs. (8-13 Nm) 4R70W Transmissions: 9-11 ft. lbs. (12-15 Nm)
  2. Add the correct type and quantity of fluid to the transmission through the filler tube.
  3. Lower the vehicle. Start the engine and move the gear selector through shift pattern. Allow the engine to reach normal operating temperature.
  4. Check the transmission fluid. Add fluid, if necessary, to maintain correct level.


FILTER SERVICE


See Figure 3
  1. Remove the transmission oil pan and drain the fluid. For details, please refer to the procedure located earlier in this section.
  2. Remove the screen and the filter from the valve body. Most screens are retained using a fastener; through some may use an interference fit between the screen tube and valve body.




0900c1528006bc42.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: After the pan is removed, you can remove the transmission fluid filter
To install:
  1. Install a new filter using a new gasket or O-ring.

If the transmission uses a filter equipped with a fully exposed screen, it may be cleaned and reused.
  1. Install the transmission oil pan and properly refill the transmission.

Aug 26, 2010 | 1996 Ford Thunderbird LX

2 Answers

My 82 ford van will not shift gears.


There is not a vacuum modulator it is electric from the gas pedal the two wires are for the electric shift

Check the valve in the valve body. One of the valves may not be sliding right

Nov 27, 2009 | 1983 Ford Econoline

1 Answer

1996 ford T-bird Lx V6 trying to remove timing chain cover to replace gasket ( oil leak above filter housing. All bolts I can see are removed, does the oil filter housing have to be removed also > and...


cover has 2-4 bolts at front of oil pan and harmonic balancer will need to be removed to take cover of of crankshaft.. lemmee kno if that solves your problem...chris..

May 09, 2009 | 1996 Ford Thunderbird LX

1 Answer

Took transmission pan off and can't find filter


2002 Hyundai Elantra has 2 trans filters. One is inside the pan which is mounted vertically. The other is located on top of the transmission case.

Apr 22, 2009 | Hyundai Motor 2002 Elantra

2 Answers

Where is the transmission filter?


from what i can gather there is no filter replacement, only a fluid exchange. this info is coming from a rather good borderline great mech. program.

Aug 19, 2008 | 2001 Kia Optima

1 Answer

Transmission filter


That car was available with 2 different transmissions.1 is the CD4E.That trans,the filter is only accessable if rebuilding the trans.You literally have to tear down the trans to get to the filter,so just drain and refill that one on a service.The other trans it could have is the GF4AEL,and that one has two pans.The filter is located in the bottom pan.Good luck.

Jul 03, 2008 | 1999 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...