Question about Cars & Trucks

1 Answer

Where is the brake pedal position sensor located ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

In front of brake pedal arm.

Posted on Nov 28, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: z3 brake light sensor

lay on your back in the drivers side and look up... it should be located just behind the brake pedal... move the brake pedal by hand and you should see the switch move

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 cadillac cts has no brake light all fuses are good and replace the brake switch.still not working any advice


Stop Lamps
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bass relay close and battery positive voltage is applied through the bass relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

Do you know where the rear fuse box is ? Check BAS fuse 15amp. and the bas relay , should be marked on the inside of the fuse box lid . The rear fuse box is located

Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Right Rear
In the passenger compartment, under the right side of the rear seat at carpet.

If fuse and relay are ok your best would be to take to a cadillac dealer .

Jan 19, 2017 | Cadillac Cars & Trucks

2 Answers

2010 Cadillac dts the cruse control don't work sometimes and the brake lights don't turn off and the switch key will not come out ,other times it works normal


The crusie control not working would be caused by brake lights being on same as for the key not coming out . You need to test the brake pedal position sensor . The brake pedal position sensor is under the dash hooked to the brake pedal arm . You need a wiring diagram to tell which wires are what . The pedal position sensor isn't like brake light switch from years past , it's an input for the BCM - body control module .There is three wires at the switch , 5 volt ref. , ground and signal . All go to theBCM . You could have a sensor problem , problem with the BCM . There could be DTC'S - diagnostic trouble codes stored in the BCM .
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.

Your best bet would bet to take it to qualified repair shop

Jan 04, 2017 | 2010 Cadillac DTS

1 Answer

Where's is the fuse located for my brake lights on my 2007 Pontiac g6 and rear defrost fuse


Stop Lamps
your br
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery positive voltage to the stop lamps, transmission control module (TCM), engine control module (ECM), and stop lamp relay coil side. When the stop lamp relay receives battery voltage from the BCM, the relay coil is energized and the stop lamp relay switch contacts close applying battery voltage through the STOP LP fuse to illuminate the center high mounted stop lamp (CHMSL).
I'd say you have more then a bad fuse ,just reading how the brake lights function .You should have it hooked up to a professional grade scan tool ,one that can check for DTC'S - diagnostic trouble codes in the BCM - body control module !
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Brake Pedal Position Sensor parameter in the data list for the body control module (BCM).
  4. Apply and release the brake pedal.
Does the scan tool display a change in the voltage?

DTC B3903 Stop Lamp Relay Circuit DTC C0277 Brake Pedal Position Sensor Circuit
DTC C0278
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
Does the scan tool display DTC C0278 00?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections

3

Recalibrate the brake position sensor.

Circuit Description
DTC C0870
The body control module (BCM) applies a ground through the brake sensor reference low circuit to the brake pedal position (BPP) sensor. The BCM supplies a 5-volt reference through the brake sensor reference voltage circuit to the brake position sensor. When the brake pedal is being applied, the BPP sensor then sends a variable voltage signal through the brake sensor signal circuit to the BCM.
Circuit/System Verification
  1. Ignition ON, observe the scan tool Brake Lamp Cmd. parameter as you apply and unapply the brake pedal. The parameter should change between OFF and ON as the brake pedal is applied and released.
  2. ?‡'
    If the parameter does not change as the brake pedal is applied and released, refer to Brake Pedal Position Sensor (BPPS) Malfunction.

  3. With a scan tool, command the LR Stop/Turn Signal Lamp ON and OFF. The LR turn signal should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the LR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.

  5. With a scan tool, command the RR Stop/Turn Signal Lamp ON and OFF. The RR turn signal should turn ON and OFF when changing between the commanded states.
?‡'
If the RR stop lamp does not illuminate when commanded, refer to Stop Lamps Malfunction.






I
I'd

Sep 26, 2015 | Pontiac Cars & Trucks

1 Answer

All brake lights and traction light Or on the dash and my brake lights will not work 2006 Cadillac CTS


The traction control system is part of ABS control module an if the light is on there is A DTC - diagnostic trouble code stored in the EBCM - electronic brake control module ! The brake pedal position sensor is an input to the EBCM , when you press the brake pedal the EBCM then energizes the BAS relay in the left rear fuse box turning on the brake lamps !
There could be a DTC like
DTC B3903
The electronic brake control module (EBCM) supplies voltage to the BAS relay coil side voltage supply circuit when the stop lamps are active. The coil side control circuit of the BASS relay is permanently grounded at G402.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B3903 Stop Lamp Relay Circuit
Or
DTC C0278
The brake pedal position sensor (BPP) is a potentiometer. The electronic brake control module (EBCM) supplies a 5-volt reference circuit and low reference circuit to the BPP sensor. The BPP sensor signal circuit is a direct input to the EBCM. The EBCM determines the BPP based on the voltage from the BPP sensor. The EBCM converts the BPP sensor feed back voltage to a digital signal and puts it on the class 2 communication bus.
DTC C0282 Brake Pedal Position Sensor Circuit Range/Performance
DTC C0283 Brake Pedal Position Sensor Circuit Low
DTC C0284 Brake Pedal Position Sensor Circuit High
DTC C0880 Device Voltage Reference Output 2 Circuit
You may want to take this to the dealer !

Jul 14, 2015 | Cadillac Cars & Trucks

1 Answer

Where is the stop lamp or brake lamp fuse and panel for a 2007 cadillac cts?


Kevin , this is a very complex way of stoplamp control , I will post GM service Description and Operation of how they work an let you deside if you want to tackle this ! Do the center high mount brake lights work ?
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bas relay close and battery positive voltage is applied through the bas relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

There could be a code stored in the EBCM - electronic brake control module - DTC B3903 Stop Lamp Relay Circuit
DTC C0278 Brake Pedal Position Sensor Not Calibrated
there are several other codes that pertane to the brake lights . you could try Replaceing the bas relay !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet.

Jun 28, 2015 | 2007 Cadillac CTS 3.6L

1 Answer

I have a Lincoln mkz 2008. sometimes I have to double pump my breaks to put my car in drive


Replace the brake pedal sensor, located under the dash on the brake pedal arm. It may be defective, causing the transmission linkage to remain in the locked park position until you jolt it by double pumping the pedal.

Feb 03, 2015 | Lincoln Cars & Trucks

1 Answer

No brake lights


brake pedal position sensor located on the brake pedal under steetring column

Apr 04, 2014 | 2000 Ford Mustang

1 Answer

Where is the brake pedal position sensor in a pontiac g6


2007 G6 pontiac brake pedal position sensor location?

Oct 15, 2012 | 2006 Pontiac G6

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...