Question about Cars & Trucks

1 Answer

Why does my Turbo R stall when put into reverse and reversing UP a slope?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

Sounds like fuel sloshes to the front of the tank and isn't being picked by the siphon. If the problem doesn't happen with a full tank of gas I'd replace the whole sending unit.

Posted on Nov 29, 2014

  • Derek Stocker
    Derek Stocker Nov 30, 2014

    Thanks Tom, I will get the mechanic man have a look at that.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 88 Answers

SOURCE: Stalls when placed in reverse

well you have convertor lock prob prob a sensor for trans let me know hey till fix ya bouy me ok

Posted on May 23, 2009

  • 1 Answer

SOURCE: Engine stalls when put in either drive or reverse on '96 caravan. I was told it was most likely the transmission solenoid. Any other causes?

try the map sensor. it is cheap and takes about 20 minutes to change. Good place to start.

Posted on May 20, 2009

  • 1 Answer

SOURCE: check engine light on, car shakes while in reverse, stalls ...

it could be your mass air flow sensor? try checking that

Posted on Feb 10, 2009

pappapumpdaf
  • 635 Answers

SOURCE: turbo 350 trans no forward gears but does have reverse

It's either your servo, or your bands.
Either way, the tranny needs a good cheap shop repair.
I'd just get a warrantied salvage yard tranny if I were you and save a few hundred bucks.

Posted on Mar 07, 2010

  • 1 Answer

SOURCE: 96 900 SE turbo, brake light and tail light

1996 SAAB 900 SE Brakelight Failure SID info
- stalls in reverse etc.

The problem lies with the grounding point in the left rear body cavity on the floor, see the diagram.
Rust eventually destorys the ground and the car will not run in reverse nor do the backup lignts or the rear hatch defroster work amongst other things
Re-attach the grounding wire to an existing welded stud on the side body panel and the problem is solved.



_452.jpg

Posted on Jan 11, 2011

Testimonial: "Thank you, I did locate that ground prior to your answer. Note it was necessary to relocate the ground due to excessive rust of that area. Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do I do to get my 99 Durango 5.9l to stop stalling when I put it in reverse?


This sounds like the transmission is seizing or locking up in reverse.

Sep 12, 2014 | 1999 Dodge Durango

1 Answer

My 2011 VW Tiguan is stalling out while reversing out of driveway...occasionally. The car is already warmed up. It's an automatic 4cyl turbo engine


First is your car still under warranty? If not we are working on an 09 Tiguan that wants to sometimes wants to die out at stops.We are replacing the in tank fuel pump and fuel pump control module.

Jan 29, 2013 | 2011 Volkswagen Tiguan

1 Answer

I have a F250 lariat with a 460 - truck stalls when I put it in gear - even after it runs for 20 min. Sometimes it will stall while I'm driving. I had carborator replaced last year. Hope you can help.


Some possible causes could be:

Vacuum leaks cause an engine to run lean witch can cause the vehicle to stall when put into gear.

Improper base idle adjustment can cause the vehicle to stall when shifted into drive or reverse

A malfunctioning or damaged carburetor can cause the vehicle to stall when shifted into drive or reverse

Improper ignition timing can cause the vehicle to stall when shifted into drive or reverse.

A malfunctioning or damaged transmission or torque converter can cause the vehicle to stall when shifted into drive or reverse

Oct 31, 2010 | 1987 Ford F 250

1 Answer

When I try to shift from park to drive it gets tight at reverse as if doesn't want go but once out of reverse it shift normally until shifting back to park when I have to go threw reverse then it tightens...


Is it only when you go from park to reverse? Or is it just as bad going from neutral to reverse? I've noticed on mine that it's often tight if I park on even a slight slope. If it only happens when going from park to reverse, try this. Hold your foot on the brake, and put the car in drive. Keeping constant pressure on the brake, go back to park, then back into drive. Did you feel the stiffness when you had your foot on the brake?

Oct 18, 2010 | 2004 Pontiac Grand Prix

2 Answers

96 900 SE turbo, brake light and tail light failure on SID. go to put car in reverse and car stalls, Note, License plate bulbs are out as well as 1 of the rear fog light bulbs, don't know if that would...


1996 SAAB 900 SE Brakelight Failure SID info
- stalls in reverse etc.

The problem lies with the grounding point in the left rear body cavity on the floor, see the diagram.
Rust eventually destorys the ground and the car will not run in reverse nor do the backup lignts or the rear hatch defroster work amongst other things
Re-attach the grounding wire to an existing welded stud on the side body panel and the problem is solved.



_452.jpg

Sep 20, 2010 | 1996 Saab 900

1 Answer

When put into drive the car shakes and stalls. It


I have a 1989 5-series BMW which sometimes stalls after changing from reverse to drive. It also sometimes shakes when first driving in reverse before changing to drive.

Jan 30, 2010 | 1992 Mazda Protege

1 Answer

1.car stalls out when you put it in gear, mainly reverse. 2.jerks and stalls when starting forward..A4..1.8T 2002 audi 1.8 turbo L4 FI 20V 112,000 miles


Sounds like your TCC (torque converter clutch) solenoid is causing improper lockup, causing the engine to stall. It works similar to putting your hand on a ceiling fan to stop the blades. I believe this is where you will find your problem.

Good Luck!

Sep 01, 2009 | 2002 Audi A4

1 Answer

'86 audi 5000 turbo


back of throttle area ducting should be tight or worn collapesed hose causeing vaccum leak

Sep 24, 2008 | 1986 Audi 5000 CS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...