Question about Cars & Trucks

2 Answers

Key wont turn ignition 2001 e320

Door locks open,lights work etc...just key wont turn ignition

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

My Hundai did the same thing. Turned out that the steering wheel was in a bind. Try playing with the steering wheel and turning the key at the same time. You can also try tapping on the end of the key with a small hammer while turning the key

Posted on Nov 28, 2014

Ad

Is the wheel locked ?? you may find the bolt that locks it has
seized up it usualy if free to move but can jam on

perhaps the lock it worn or has something inside the barrel not allowing key syncro
so use some wd40, a good rag and give it a good wash out
half a can and pull the key in and out and etc rewash and try again this will also free any parts that are stuck up

Posted on Nov 28, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: 2001 Grand Am GT interior

a la mejor tiene malos los fusibles o se descompuso la computadora
lo mas probable es que se haya descompuesto la computadora del auto

Posted on Sep 02, 2008

unvme
  • 266 Answers

SOURCE: 1999 e320 fog lights and parking lights won't tunr off

replace the light switch

Posted on Jan 25, 2009

  • 15 Answers

SOURCE: e320 car key doesn't work

you have to get another key from the dealers and program it.you key is out of alignment . common on mercedes

Posted on Feb 13, 2009

  • 15 Answers

SOURCE: 2001 mb clk 320, my ignition switch will not turn.

Hi there
I had something similar on my merc
but yours sounds similar.
the fact that you say the steering lock no longer works is very worrying, most times the key not going past position 1 is due to the steering lock being actuated and the pressure in it has to be released before the key will turn, you will have to go from lock to lock the find where the steering lock actuates when this happens follow my wiggle method of turning the steering wheel slightly when the steering lock is on the disengage it. ie keep trying the key whilst wiggeling the steering wheel.
hope that helps

Posted on May 01, 2009

  • 2 Answers

SOURCE: my renault laguna 1999 rt remote key fob wont work?

IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 T-BIRD WONT START, TURNS OVER, THEFT LIGHT BLINKING, OWNER LOST KEYS, HAD NEW KEY CUT STILL WONT RUN


I would go after the door lock first. Older fords have a switch on the door lock that disables the alarm. They tend to break and fall though. I have replaced them with a momentary on/ff switch.But the alarm would go off when opening the door. On some older ones(85,87)(no keypad) I could disconnect the security module and it did just fine.

Jun 26, 2016 | 1989 Ford Thunderbird

1 Answer

How can I lock a renault megane 56 plate without the key card as it is not working


Locking/Unlocking the doors from the outside
This is done using the RENAULT Card; see the "RENAULT Card" information in Section 1.
In certain cases, the RENAULT card may not work:
- if the RENAULT card battery is weak, flat, etc.
- if equipment operating on the same frequency as the card (mobile phones, etc.) is used;
- vehicle located in a high electromagnetic radiation zone.
It is then possible:
- to use the key integrated into the card to unlock the front left-hand door;
- to lock each of the doors manually;
- to use the interior door locking/unlocking control (refer to the following pages).
Using the key integrated in the RENAULT card
Insert key 1 into the lock in the driver's door and lock or unlock. Locking the doors manually
Turn screw 2 with the door open (using the end of the key) and close the door.
This means that the doors are then locked from the outside.
The doors may then only be opened from the inside or by using the key in the front left-hand door. Interior locking/unlocking door control
Switch 3 controls the doors, boot and, depending on the vehicle, the fuel filler flap simultaneously.
If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly.
If you need to transport objects with the boot open, the other opening elements can still be locked: with the engine stopped, press switch 3 for more than five seconds to lock the other opening elements.
Locking the doors without the RENAULT card
For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc.
With the engine switched off and an opening element (door or boot) open, press and hold switch 3 for more than five seconds.
When the door is closed, all the doors and the tailgate will be locked.
Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using the key integrated in the RENAULT card.
Door and tailgate status indicator
With the ignition on, the warning light integrated in switch 3 informs you of the locking status of the opening elements:
- indicator light on, the doors and tailgate are locked,
- indicator light off, the doors and tailgate are unlocked.
When you lock the doors, the indicator light remains lit and then goes out.

Dec 12, 2015 | Renault Megane Cars & Trucks

1 Answer

Key wouldnt open door today put key in ingition it wouldnt start, no lights coming on at all? it isnt the battery as its been checked


The Key would not work the Door Lock or your Remote?

Corrosion on your Battery if no lights are coming on or your Battery is going bad and you need to recheck it

Apr 12, 2013 | Cars & Trucks

1 Answer

Central locking wont work cant open it except drivers door with key only,but alarm still work with key fob.


put key in ignition turn key to number 2 lights on dash battery etc. then press the fob. till the doors lock then it is rest.

Jan 23, 2013 | Vauxhall Cars & Trucks

1 Answer

Mazda 6 2005 driver door jammed


if you talking about door latch wont let door close.try to reset all door locks.first if you cant get door close.work unlock button with remote or door switch.then hold open door handle while you flat screw driver pull up latch in door latch should stay up so door will close.once get door close.try resetting all door locks by sitting inside vechicle with all doors close.remove key from ignition.open drivers door.wait 24 seconds.turn ignition switch on and back to lock position 3 times.press and release drivers door courtesy light 3 times.ensure doors lock and unlock.if not wait 40 seconds and repeat procedure.if this procedure fails. you have problem in the door latch and lock mechanism inside the door itself.

Jan 04, 2013 | 2004 Mazda 6 Sport

1 Answer

2007 yaris door wont lock when driver door is open


sounds like the ignition lock is worn out.

Mar 01, 2017 | 2007 Toyota Yaris 1.4

1 Answer

How do you program new spare key for 2007 rodeo RA?


if its the ignition key it must be done by a dealer and have a lage black plastic head which has got a transponder in it. If you got a blank key cut at the locksmith it will turn the locks but wont start the car. Usually you get the dealer to do both supply ignition key and then get it cut, then they can program it.

but if your asking how to program the keyless entry remote follow this procedure.
take note step 5 is different for different year models.


Make sure that all the doors are closed and unlocked and wait for dome light to go out before starting.


Insert the ignition key into the ignition switch


Open drivers door


3 on/lock


Close/open drivers door


Wait 8 secs


On/lock/on (MY06-07) OR 2 on/lock OR on/lock (MY08)


Close drivers door


Hazards flash


Press remote & keep pressing one button & then the other slowly(2 secs) until locks start working(they wont operate if key is in ignition).


Hazards flash

Feb 23, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

1 Answer

Key no longer works in ignition. I stopped to gas up and the key I normally use would not open the gas cap door. I re-entered the car and the key would not turn the ignition. The key unlocks the steering...


take it to a lock smith to remove the broken part or you could jam the broken part down to where the ignition will turn with the broken key. I advise taking it to a lock smith to remove the broken part

Feb 02, 2010 | 2001 Toyota Tundra

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...