Question about Nissan Cars & Trucks

2 Answers

How do I change rear wheel bearing on 2009 k12 nissan micra

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 3,382 Answers

That should be in the service manual: You can search for one using Google and this in the search box: "2009 k12 nissan micra service manual" without the quotes, it should show a lot of different sources for one.

Posted on Nov 28, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

Remove rear brake drum on the inside of the drum you can see the bearing remove the snap ring and press it out from the stud side put it back in reverse and don't forget to get a new snap ring!

Posted on Jul 03, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

  • 35 Answers

SOURCE: how do you change rear wheel bearing on a 2004 nissan sentra

Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.

Posted on Mar 21, 2009

95_Bravo
  • 16 Answers

SOURCE: Rear wheel bearing diagram

The bearing is pressed in so you will have to carry the hub to a machine shop to have the old bearing pressed out and the new bearing pressed in once you have the hub off the car.

Process to remove hub is as follows (from the 1990 Miata Service manual)

Remove rear wheel, rear wheel brake caliper assembly (suspend with a rope), and disc plate.

Check for rear hub play with a dial indicator, if excessive play either tighten the locknut or remove hub and replace bearing.

To remove bearing bend up the locknut stake and remove axle nut - torque is between 159 - 217 ft pounds.

Now remove the hub, retaining ring, rear wheel knuckle, wheel bearing (if loose), dust cover.

Replace with new parts, locknut, dust cover, knuckle bushings and hub bolts (if worn).

Take knuckle with wheel bearing to machine shop and have old bearing pressed out and new bearing pressed in.

Assembly is reverse of the above.

I have personally found that by the time I pay a machine shop to do the removal and reinstall of the bearing and take my time into account it is less expensive to pay a good shop to do this work for me.

DIY information at Miata.net

Posted on May 10, 2009

motorhead427
  • 24 Answers

SOURCE: how to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuel filter on k12 micra 2005


http://www.micrak12.com/engine.htm go down the list till you read fuel filter

Feb 02, 2018 | Cars & Trucks

1 Answer

Nissan micra central locking locks but makes a grinding sound on on side of the car.


Put your ear to the door and listen to where the grinding/buzzing noise is coming from when you lock the door, sometimes it maybe more than one door! The door it's coming from need a door actuator, common fault with the k12 micra's, which i'm guessing this is a k12 model!

Feb 04, 2015 | Nissan Cars & Trucks

1 Answer

Tach signal wire


Ask google search. Lots to surf.

Aug 10, 2014 | 2006 Nissan Micra 1.2

1 Answer

Nissan micra fuse box


Fan not coming on for Nissan Micra K12 (March)

Dec 13, 2011 | Cars & Trucks

1 Answer

What oil should i use for nissan micra k12


cheapest 20/50 or 10/40 ,change oil every 6000 miles with a oil filter every thrid oil change ,normal or synthetic will do ,but change it regular as stated do not be fooled by the so called long life oil or the prices charged

Dec 12, 2010 | 2003 Nissan Altima

2 Answers

Blower heater unit in micra k12


hi did you get the resistor fixed if not you need to remove the glove box by removing the screws that can be seen then there are two plastic lugs that need to be pulled out sideways to enable you to remove the glove box then you will see the resistor card on the side of the motor thats on the new shape micra k12

Mar 03, 2010 | 2006 Nissan Z

4 Answers

Nissan micra k12. not idling properly, low power, not staring all the time. continuous problem. replaced throttle with 2nd hand part. better for a while. now car wont start, if it does it hunting,(sound...


HI, I GOT NISSAN MICRA 1.2 SE 2005 PLATE ONLY DONE 59000 MILES. MISSING! I HAVE CHANGED COIL PACKS, CAMSHAFT SENSOR, TIMMING CHAIN, STILL THE SAME PROBLEM. I HAVE ALREADY SPENT 1000.00 POUNDS. IS THERE ANYONE WITH SAME PROBLEM?

Jan 29, 2010 | Nissan Micra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...