Question about 2001 Mercury Sable

1 Answer

How do i change the air temperature sensor on a 01 mercury sable

Google you tube and everybody i know

Posted by on

1 Answer

Air Temp Sensor should be included
inside the MAF Sensor--- isn't it?

No reason that should be bad

Has it been tested or scan tool data looked at?

You don't change parts on a guess, for no reason

Any codes you may have,got nothing to do with
changing parts

Posted on Nov 28, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: Oxygen Sensors

ok Bank 1 is the rear bank and bank 2 is the front bank sensor 1 in each bank is the one closest to the manifold they have green connectors sensor 2 is the sensor after the cat converter and is a blue connector

Posted on Dec 02, 2008

  • 1 Answer

SOURCE: 2003 mercury sable, not idleing right

I was looking under the hood, and noticed that i could hear air rushing around. I found that a vacum hose had decayed and cracked. After i replaced that, everything has been fine

Posted on Jan 13, 2009

  • 1 Answer

SOURCE: 2000 MERCURY SABLE

My 2000 Sable starts blowing hot air about every 6 months. I mean like an oven. All I do is disconnect the battery negative terminal for about 5 minutes. After I re-connect the problem is solved. This solves many problems on this car, it just needs a re-boot. It must be powered by Microsoft (ha ha). Good luck. ps my auto headlamps never did work right either. Dave.

Posted on Apr 21, 2009

  • 11 Answers

SOURCE: mercury sable 2002 serpentine belt change

There are also two serpentine belt types for the 2002 sable. The S and U type engine. Take the old belt with you the the parts store. As for the diagram, I googled it under images and about a dozen correct ones came up. Remember the 2002 sable is the same as the 2002 Tarus.

Posted on May 02, 2009

warlock61
  • 659 Answers

SOURCE: location of the camshaft position sensor in a 2004 mercury sable

it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the dpfe holes located


The DPFE itself is a sensor. It plugs on top of 2 Vacuum lines that are usually Silicone and high temperature capable. The other end of the Vacuum lines attach to a metal tube coming from the exhaust pipes. The DPFE measures the flow inside this exhaust tube and adjusts the engine accordingly.

The metal tube can rust and often if there is a metal joint that hides the rust. Any leak in this tube will render the DPFE useless.

Dec 07, 2013 | 2004 Mercury Sable

1 Answer

2001 Mercury Sable: code for System Lean to Bank 2= Car Idles too high. Possible causes?


sounds like a air leak ,, bank 2 sensor 2 ?? refers to after the catalytic converter ... could be a faulty sensor but more likely an air leak .... even a faulty fuel tank cap seal is enough to cause problems on these systems

Nov 06, 2013 | 2001 Mercury Sable

2 Answers

I have a 2004 Mercury sable 24 valve. It sputters and now it will cut off when I try to accelerate.


When was last fuel filter change? For that matter when was last tune up? Seriously, sounds like fuel filter, especially this time of year. With big temperature swings condensation (water) forms in fuel tank. Run a bottle of STP gas treatment through it then change fuel filter.

Jan 06, 2011 | 2004 Mercury Sable

1 Answer

Temperature will not change when you set the temperature control from 60 to 90. I getting heat but not hot just warm. I have climate control on a 2004 Mercury Sable LS


I've seen this before. There is heat mix solenoid just behind the stereo that moves the mix door to determine the air temperature at the vents. The solenoid has likely failed and needs to be replaced.

Nov 12, 2010 | 2004 Mercury Sable

2 Answers

Where is the Air Flow Meter/Mass Air Sensor on a 1993 Mercury Sable and it is easy to replace?


The MAF or mass air flow sensor is located on a tube connecting the air filter box to the throttle body. Just unplug the connector and unscrew the sensor then pull it out.

Aug 11, 2010 | 1993 Mercury Sable

1 Answer

Location of the camshaft position sensor in a 2004 mercury sable


it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

May 01, 2009 | Mercury Sable Cars & Trucks

1 Answer

05 mercury sable check engine po174


You has a vacuum leak on the engine.

In order to troubleshoot this, you must start with a clean engine wipe down.


The major offender parts are


air intake gasket on the manifold

air tube after the mass air flow sensor

rubber seal under idle air control IAC motor

===

Warm up the engine for 15-20 minutes (LEAVE THE engine at idle) then spray a little Barmen carburetor clear on the potential air leak location (ONE AT A TIME) and listen for a surge in rpm.

If the engine speed go higher that's mean the carburetor clean (ADDITIONAL FUEL) got into your engine and that's the gasket you need to change.

There may be multiple leaky spots so take your time and check all rubber gaskets,sensor and hose that are lead into the intake manifold.

When you finish fill up with one tank of Chervon to clean out the injectors.

Please post more information after your inspection.

Apr 12, 2009 | 2005 Mercury Sable

1 Answer

Temperature gage


you are low on coolant and you have brown coolant. need a bypass kit.

tsb 01-11-6. post email and I will send tsb to you.

Jan 16, 2009 | 2000 Mercury Sable

Not finding what you are looking for?
2001 Mercury Sable Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...