Question about Cars & Trucks

2 Answers

What is a caliper and where is it on my 2004liberty jeep

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

A caliper is the part that squeezes the brake pads against the rotor when You push the brake pedal. Located behind the wheels

Posted on Nov 27, 2014

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

You have two up front behind the wheels and two in back too.

Posted on Nov 27, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tail light left side dont work but works when I applied the break 2004liberty jeep


loose connection some were or you have lost the grounding to that tail light. sometimes it't within the tail light itself.

Dec 05, 2014 | 2004 Jeep Liberty

1 Answer

2011 jeep patirot rear caliper piston won't retract


I personally use a big C CLAMP gently squeeze it in

Apr 18, 2014 | 2008 Jeep Patriot

1 Answer

Chik engean


older post.
the PCM sees the heater is dead, (not drawing current)
so is bad,or wire to it cut.
PCM cant tell which, only you or a tech, can.
S1B1 means left front sensor.
this failure is common after 100k miles, and is simple.
the heater is blown open or wire cut. 1 or the other.
the heater can short too. no matter, same action,

Nov 27, 2013 | 2005 Jeep Liberty

1 Answer

How to remove front rotors on 05 jeep liberty


remove the caliper by removing 2 bolts on the inner side of the caliper (15/16 size I think) then pull the caliper off the rotor. dont remove the brake hose or let the caliper hang by the hose (set it on a bucket or use a piece of wire to tie it to an A arm) then the rotor will pull off easily.

Oct 25, 2011 | Jeep Liberty Cars & Trucks

1 Answer

2002 Jeep Grand Cherokee Laredo 4.0L front passenger brake sticks


First you must look closely at the caliper and determine if it is sticking on the slide or is the piston sticking. If it is the piston you would have to rebuild the caliper or replace the caliper. If it is the slides, you need to sand and clean all the slide contacts and lube the slide with lithium grease or never seize grease. Then you can reinstall the caliper and you will be fine. Also when checking if the piston is sticking try loosening the line and see if it retracts, if it does you may have a bad flex hose going to the caliper holding pressure on the caliper.

Jan 30, 2010 | 2002 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee Limited front brake will not release?


either front flex hose or caliper.slack the bleed screw on caliper,if brake releases then problem is rubber flex hose,if dont relaese it is caliper

Aug 09, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How do i take a rear rotor off 2004 jeep cherokee


Remove the caliper slide bolts and take the caliper loose and hang caliper with a wire to something. Don't let the weight of the caliper to be supported by the brake hose.

Next, remove and discard the O-ring securing the rotor to the axle studs, and remove the rotor. Hope this helped and good luck.

Jul 19, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Torque setting for brake caliper mounting bracket


according to manual,
front caliper mounting bolts are 11 ft lbs
rear caliper mounting bolts are 220 inch lbs.

Jul 02, 2009 | 2005 Jeep Liberty

1 Answer

Jeep Commander Rear Brake Pad Installation


Per Chilton Auto repair manual:

Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

May 17, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...