Question about Cars & Trucks

1 Answer

Asd fuse making a clicking noise - Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Doubt that it is a fuse clicking but rather a relay.. fuses normally cut power to an overloaded circuit.

Posted on Nov 27, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

no_signal_sw
  • 273 Answers

SOURCE: My ASD fuse is making

ASD fuse is called an AUTOMATIC SHUT DOWN FUSE. The ASD sense circuit informs the PCM when the ASD relay energizes. A 12 volt signal at this input indicated to the PCM that the ASD has been activated. This input is used only to sense that the ASD relay is energized.
When energized, the ASD relay supplies battery voltage to the fuel injectors, ignition coils, and the heating element in each oxygen sensor. If the PCM does not receive 12 volts from this input after grounding the ASD reley, it sets a Diagnostic Trouble Code (DTC).

Posted on May 18, 2011

  • 4977 Answers

SOURCE: my 2001 neon wont start

have you checked for voltage at the starter for each terminal when there is to be voltage at each terminal.also you could have a bad asd relay that is working only on one half of the circuit but still makes a clicking noise.

Posted on Jun 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The 25 amp ASD fuse keeps blowing when i try to start myTown & ountry 2001


In that case you have a dead short somewhere. This suggests replacing the ASD relay, and there is a neat trick using a bulb instead of a fuse to track the problem.

https://www.2carpros.com/questions/2001-dodge-caravan-asd-fuse

And 'Chrysler Tech' here has good advice as to what is causing it.
http://www.chryslerforum.com/forum/chrysler-pacifica-15/asd-fuse-blowing-right-away-help-23819/

25 amp ASD fuse Google Search

Jan 25, 2017 | Cars & Trucks

1 Answer

Why asd fuse keeps blown


You have a Chrysler , dodge , or Plymouth ? ASD Fuse supplies power to ASD relay ,if you have a Dodge , Chrysler or Plymouth vehicle . You have a short to ground , videos on you tube , how to find a electrical short ! ASD - auto shut down , this powers Ignition system , fuel injectors , O2 sensors . A short in any one of these systems will blow the fuse . O2 sensor wires get melted on exhaust pipes an manifolds ! That is if you have one of these make vehicles !

Sep 28, 2016 | Cars & Trucks

1 Answer

Where is the ASD relay located


In the fuse and relay box in engine compartment

Jun 26, 2016 | Cars & Trucks

1 Answer

No power going to the fuel pump


first check all fuses.
well if the security lamp is on, and the IMMobilizer light glows
it will never run. (by design) (2 seconds max)
so are the lights glowing?
no power going. (when,)
did you read the FSM on the staged events to get engine started.
my wild guess? (sad i have to ask) is it wont start?
1: IMMO not active
2: battery charged volts near 12.6vdc rested.
3: starter cranks fast. and ASD closes
4: ASD relay sees good spark and CKP, and CMP sensors.
5: engine starts, if #4 is good then it sustains running.
if not ASD drops out in 2 seconds. killing INJECTION.
it cuts the fuel pump too.

the PCM will throw a DTC error code (did you scan it cranking ??)
for if the ASD fails to OUTPUT 12v. at step 3.

the PCM closes it, then looks, and if output is bad, it ends this event and logs the failure..

to check the pump , it takes 2 people
one at the key, and one at the pump wires.
or you WILL miss the 2second event.

one way to avoid all that is to hold finger on the ASD relay
and keyon and see if it clicks closed.
if not ., no need to check pump ,its LAST in the chain,
if the ASD clicks and drops out, during that click the pump does run
for 2 seconds, min.,
if the ASD is dead, check the PCM control line to the ASD for
making coil energized in the ASD relay, (12vdc across it for 2seconds)
if the coil is energized, and the DTC throws, for bad ASD , it is.
if the ASD goes, hot only for 2 seconds, again use any $9
scan tool to see the error.
here is the scan too tests. most books forget.
1: scan tool connected.
2; Crank engine for 5 seconds, (min)
3: release key. BINGO, the ECU tells you why the ASD dropped out.
eg: ASD error, CMP error, CKP errors or others (spark?)
does RPM read near 250rpm cranking? on the scan tool?
Is TPS throttle angle near 100% (cutting fuel) ? bad tps. (cut wires)


fixing cars without a $9 scan tool , as sold on feabay is 100x harder.
get the tool and use it.
they rent them cheap or loan them for free.
not to be confused with a code reader, which are near useless.
imo.....


Feb 11, 2014 | 2004 Jeep Grand Cherokee

1 Answer

My 2001 neon wont start and the asd relay in the fuse box is making a clicking noise. i replaced the starter , new battery tested the alternator what could be the problem


have you checked for voltage at the starter for each terminal when there is to be voltage at each terminal.also you could have a bad asd relay that is working only on one half of the circuit but still makes a clicking noise.

Jun 09, 2011 | Plymouth Neon Cars & Trucks

2 Answers

My ASD fuse is making a clicking noise and vibrating. What is the function of this fuse?


ASD fuse is called an AUTOMATIC SHUT DOWN FUSE. The ASD sense circuit informs the PCM when the ASD relay energizes. A 12 volt signal at this input indicated to the PCM that the ASD has been activated. This input is used only to sense that the ASD relay is energized.
When energized, the ASD relay supplies battery voltage to the fuel injectors, ignition coils, and the heating element in each oxygen sensor. If the PCM does not receive 12 volts from this input after grounding the ASD reley, it sets a Diagnostic Trouble Code (DTC).

May 18, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Will not start. have jumped battery. will get enough juice to make the key in ignigtion warnig bell but will not turn orver


when you cycle the key.do you hear a fuel pump noise it will be on for 3 seconds, cycle it. you should hear it, if you dont go to the battery junction box fuse area, and check the fuses. and make sure the fuel pump fuse is not shorted out. also when you cycle the key to ACC do you hear a click in that box area? This vehicle is ASD relay control ill keep my eye on this post if you repond to me i ll respond if some one else you respond to let them help you

Apr 30, 2011 | 1997 Dodge Neon

1 Answer

2005 Dodge Durango, clicking noise coming from the engine (sounds like it is coming from the fuel injectors and the fuse box) car starts, runs fine, no warning indicators. Remove ASD fuse??? and it stops.


ASD relay faulty? Try swapping it with same number from other relays & see if clicking stops. I believe there is others same # in there, but might not be. Get back to me if not.

Jul 18, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...