Question about 2004 Renault Megane 1.9
I tried this morning, i opened the trunk, remove the light box from the cable but i can't get to open the plastic and to reach to the bulb...
The light box is removed from the outside of the car. Depress the plastic clip on the end of the fixture from the outside . Pull down and angle it so the fixture slides out of the hole. Lift out and remove the lens. It comes off the black plastic base by gently spreading the side. I assume you are replacing it with an led. Just reverse the procedure .
Posted on Nov 27, 2014
Testimonial: "Thanks so much , i succeeded"
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
work it manually and it should work ...ie put the key in the door and open and lock the door 3 times slowly then jump in and try to start within 15 secs .if it doesnt work then be prepared to be fleeced and lay the golden egg at the dealers
Posted on Nov 23, 2008
it's a real nightmare to try to change it from inside..i tried and hardly succeeded on my clio campus 2007...yours is clio III, I suppose..so it should be the same system..you need a wrench tool of size 10 (mm)..and you will need to dismantle the front lapmp..don't worry..the level of the light beam is adjusted by the mechanism which is holding the light bulb in place, not the angle of the front lamp.
Posted on Dec 28, 2008
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
I had same Problem with 03 Megane about 6 weeks ago
and the fault on mine was the one of the Coils had gone.
got replaced £270.00 later working fine....
just happened again with same message Check Injection.
RAC told me injection has gone, so now yet again back in the garage.. How i wish i never brought a Megane
Posted on Nov 18, 2009
When the airbag light (SRS) is on or blinks it means a fault has occurred in the system and the airbag diagnostic monitor has disabled the system, the most common problem that turns the light on is a break in the connection to the steering wheel mounted airbag, this is due to a rotating ribbon contact that breaks under the steering wheel that connects the airbag to the wiring harness and the diagnostic monitor, the part is called the clock spring contact, a coiled up ribbon electrical contact that turns with the steering wheel while maintaining a mechanical connection to the airgag mounted on the steering wheel, to replace this part you must disarm the airbag system and remove the steering wheel, this requires a special steering wheel puller tool and that you disarm the airbag system before you start the work, to do this disconnect the battery negative cable for 1/2 hour prior.
Posted on Apr 27, 2010
Tips for a great answer:
Jan 29, 2016 | Cars & Trucks
Sep 07, 2015 | 2005 Renault Megane 1.6
Feb 24, 2015 | 2003 Renault Megane
Jan 04, 2015 | 2002 Renault Megane
Aug 08, 2014 | 2003 Renault Megane
Apr 02, 2014 | 2006 Renault Megane 1.5
Jun 18, 2013 | Renault Cars & Trucks
Nov 14, 2012 | Renault Cars & Trucks
May 07, 2012 | 2005 Renault Megane Scenic
May 15, 2010 | 2008 Chevrolet Malibu
141 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: