Question about Chevrolet Silverado 1500

1 Answer

My tensioner is bobbing back and forth like a bobble head doll making a knocking sound, do I need to replace the tensioner?

Got a 1990 chevy k5 blazer wit 350,

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Click on the link below. They are all nearly the same as far as removal goes. Good luck with it. If you can help it, do not completly remove the belt.
How To Install Replace Belt Tensioner Idler Pulley Chevy GMC Silverado...

Posted on Nov 27, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Engine replacement 1996 Chevy Blazer

I just replaced my engine in my 1996 blazer myself. Body need not come off, but what an ordeal if its a 4 X 4.

Posted on Oct 01, 2008

DAD5bbbbg
  • 111 Answers

SOURCE: replace a steering column on 1989 chevy k5 blazer

The best thing to do is to buy a Chilton,s repair manual. It has step by step procedures. You can get one at most auto parts stores. They coast anywhere from $10-$30 dollars.

Posted on Mar 16, 2009

  • 2002 Answers

SOURCE: Need vacuum diagram

I can't send you a diagram but I can tell you the basics that should get you mobile. Take a vacuum line from the lower front of your carb and hook it to your distributer vacuum advance. Take another from the front of your carb and run it to your EGR valve. It should be beside the carb on the intake manifold. At the rear of your carburator there is a large line coming out. It should be steel. It provides vacuum boost to your power brakes. Hook it up. Make sure all other vacuum outlets on the carb and intake are blocked off and you should be able to get mobile.

Posted on Jun 06, 2009

smartr10U
  • 1305 Answers

SOURCE: What do I loosen to release and add tension on the

There is a belt tensioning pulley. It's spring loaded and if you put a wrench on the center nut you should be able to remove the tension on the belt...

Posted on Nov 20, 2009

Testimonial: "Problem solved and thanks!"

  • 1 Answer

SOURCE: 91 Chevy K5 Blazer turn signal flasher

i agree with them, but you know when you open the door and thatgod damn buzzer goes off until you turn on the truck? how the hell do you shut that off?
please email me Steveracer8@hotmail.com
thanks

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Chevy Blazer K5 5.7 engine: has engine ping


The temperature sensor is where I would start. If the sensor tell the computer that the engine is cold it will initiate the warm up mode which includes advancing the timing along with a rich fuel mixture. Unfortunately, there are many sensors that assist in controlling timing and fuel mixtures that it is difficult for me to give you a guaranteed solution.

May 27, 2010 | 1990 Chevrolet S-10 Blazer

1 Answer

I have a 1997 Chevy Blazer LS, the fuel gauge constantly fluctuates. Usually when I first turn it on the gauge will indicate more gas than is actually in the tank. Slowly as the car is running I see the...


all later model chevy vehicles are plagued with this problem it,s the fuel level sensor mounted on the fuel pump module inside fuel tank unfortunately on some models it,s only available with purchase of whole new fuel pump module that can run as much as $500.00 dollars for just the module not including labor to drop fuel tank and replace I encourage you not to waste time and money with aftermarket less expensive pump module assemblies not to knock any parts people but our shop just installed the 3rd napa fuel pump module in a 98 blazer because the new pump will not read correct amount of fuel finally it was replaced by a pump module assemblie from dealership at cost of $458.00 for pump it now reads correct hope this helps if you need more detailed instructions on how to replace repost at fix ya thanks

Apr 04, 2010 | 1997 Chevrolet Blazer

1 Answer

1990 chevy s10 blazer 4wd. Xmsn whines.


if this happens only in the morning after you start for the first time its the clutch on the fanblade needs replacing

Dec 02, 2009 | 1990 Chevrolet S 10 4WD

1 Answer

What do I loosen to release and add tension on the serpentine belt for belt replacement on my 1990 Chevy S-10 Blazer with 4.3 liter V6 and AC?


There is a belt tensioning pulley. It's spring loaded and if you put a wrench on the center nut you should be able to remove the tension on the belt...

Nov 20, 2009 | 1990 Chevrolet S-10 Blazer

1 Answer

No power to the fuel pump on a 1990 K5 blazer need a wiring diagram for that model to trace the power wire back from the fuel pump


CHECK FUSE + RELAY TO FUEL PUMP.IF THEY CHECK OUT GOOD.YOU HAVE PCM PROBLEMS. MAKE SURE PCM FUSE IS GOOD.YOU CAN BUY A HAYNES REPAIR MANUAL.IT HAS ALL OF YOUR ELECTRICAL DIAGRAMS.

Nov 10, 2009 | 1990 Chevrolet K1500

1 Answer

I have a 1977 chevy k5 blazer.i replace the alternator but wend I turn on the heat and the lights the volt drop down. i wonder what else could be the problem.


is it a one wire system? if it is make sure all you grounds are grounded good meaning take them off and scratching the frame down and recontacting it, I have a camaro and it was doing the same thing checked my ground and it was that so try that hope this helps good luck

Mar 24, 2009 | 1990 Chevrolet K1500

1 Answer

Replace a steering column on 1989 chevy k5 blazer


The best thing to do is to buy a Chilton,s repair manual. It has step by step procedures. You can get one at most auto parts stores. They coast anywhere from $10-$30 dollars.

Mar 16, 2009 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...