Question about Hyundai Cars & Trucks

2 Answers

On the Hyundai accent 06-2000 when the control arms are put back on the car why have they little groves so to lock on washer is this to be done up with car of ground or on stands not on suspension,

My Hyundai accent 10 not a problem but this year since 289000 I am replacing all bushings shocks mounts tie rode ends ,front control arms with bushings new sway bar bushings links front and back,done timing belt water pump my clutch is on the larst adjust I have new flywheel from Korea clutch exsedy,but yet to do,and had rattly callipers on closer look they were aftermarket so I went to wreckers got genuine Hyundai and refurbished fixed that problem.so now I have a noise when I go over bump like pl. Play somehow not from wheel its got me any clues I have checked everything over but can't identerfy noise

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 58 Answers

I had a Hyundai that the dealer keep say they don't find any thing wrong.( that is their famous warranty excuses.) Finally I convinced them if they don't find any thing wrong visually, it must be in the strut. They replaced the right side strut where the noise was coming from. Took them a year and a half to finally fix it. After a lifetime of fixing cars, here is my conclusion. The more you see of a brand name car on the road with the least TV commercials, they will be the better choice of cars. Example : You see many Toyotas on the road but how many TV commercials you see about them. Good cars sells themselves.Don't believe anything on TV, even the national news.

Posted on Nov 27, 2014

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

Do all those bushes etc and noise will go ans so will play. Check rack mounting too

Posted on Nov 27, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2003 Dodge Durango clunking noise in front end can

With the information given this is not a sure solution. Questions that need to be asked is when does this happen, turning at slow speedm high speed, when hitting a pot hole etc? Since you have replaced a lot of things already, assuming you have NEW good quality parts so you did not replace bad parts with new bad parts i would definitelu check the pitman arm. This runs from the stering gear to the tierod. It can give you some good clunks while steering, especially at low speed when there is a lot of resistance. Check it by having someone turning the steering wheel when watchin/feeling it.

Posted on Sep 18, 2009

  • 5371 Answers

SOURCE: Have replaced all tie rods; inner&outer;struts&upper mounts;sway bar bushings & links;lower control arms with ball joints& passenger side upper motor mount.none of these have changed this noise even s

What noise? And year and make of car?
A clicking noise on turns is a worn CV joint on the axle shafts. A grinding noise at one of the wheels could be a wheel bearing. Worn brake pads may cause squealing, screeching other high pitched noise.

Posted on Jul 25, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install a lower balljoint on a 2007 hyundai accent?


Most of those are pressed into the lower control arm and are replaced as a complete assembly. Replace the entire lower control arm.

Jul 30, 2014 | Hyundai Accent Cars & Trucks

1 Answer

Hyundai accent 2004 shifter is locked and brake lights do not work


Automatic transmission, right? Likely cause is the brake pedal switch located on the brake pedal arm near the firewall. This switch controls an interlock solenoid, a safety feature, that will not allow the shifter to move unless the brake pedal is depressed. Another possibility is the brake relay located on the under-hood fuse panel. Good luck.

Oct 04, 2013 | 2002 Hyundai Accent

2 Answers

How to replace the motor for windshield washer fluid in hyundai accent


Dear Sir:
Please proceed according with this page. God bless you
http://www.ehow.com/how_4448916_change-windshield-wiper-motor.html

May 24, 2012 | 2005 Hyundai Accent

1 Answer

2000 HYUNDAI ACCENT, problem is the Windshield Wiper operation is malfunctioning, in the Delay mode, and in the off position, Windshield Wiper arms/blades stop at the half point on the Windshield glas


The park position is controlled inside the motor/actuator assembly. Not sure if it can be repaired. See if it is assembled with screws versus rivets. A new assembly is less than $100.

Jul 05, 2017 | 2000 Hyundai Accent

2 Answers

Good morning changing haed gasket on 1.5 hyundai accent how much torque for head bolts and rocker arm bolts


cylinder head bolts 52-55 ft lbs. engine cold 59-63 ft lbs. engine hot

rocker arm shaft bolts 15-20 ft lbs.

intake manifold bolts 11-15 ft lbs.

exhaust manifold bolts 22-30 ft lbs.

valve cover bolts 79-81 in lbs.

May 12, 2011 | Hyundai Motor 1998 Accent

1 Answer

How to replace the bottle in which contains water for windshield in a hyundai accent?


locate bottle first, its held down by two screws or they slide in groves on fender

Feb 17, 2011 | 2001 Hyundai Accent

1 Answer

2001 Hyundai Accent dies while driving


I had a similar problem and had an engine tune up done and the car runs almost like new now. Mine is a 2001 Hyundai Accent too.

Apr 16, 2009 | 2001 Hyundai Accent

1 Answer

Wiper blades


hi from uk to remove wiper blades? lift the wiper arm off screen to fully up then turn wiper blade upwards so as to make letter T then if you look at the horseshoe type bend on the arm? where blade fits you will see a little press clip which is part of the wiperblade fitting/securing ? to this blade u section just press clip in with finger and at same time push blade downwards out of the u part of arm then you can refit new blade/s the drivers and passenger wiper blades are different lengths when you fit new blades be sure the clip locks into place ? hope this is clear instructions to understand ?

Nov 16, 2008 | Hyundai Motor 1998 Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...