Question about 2006 Chrysler 300

2 Answers

How much torque should be applied to a chrysler 300 2006 3.5L and torque for the intake manifold?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 21 Answers

The recommended torque is 40 ft pounds. Use common practices when tightening engine head bolts.

Posted on Nov 26, 2014

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Data I have found indicates that a torque of 250 inch pounds is appropriate for these 13mm bolts. Torque them in a circular pattern starting from the center pulling through several times. DO NOT OVERTIGHTEN!

Posted on Nov 26, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

LT1Rob
  • 55 Answers

SOURCE: Torque Spec for '99 Chevy C1500 5.7L engine lower intake manifold

On 5.7L engines, install the bolts and torque in sequence as follows:

  1. Step 1: 71 inch lbs. (8 Nm).
  2. Step 2: 106 inch lbs. (12 Nm).
  3. Step 3: 11 ft. lbs. (15 Nm).
f2266b6.jpg

Posted on Mar 14, 2009

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

chuck943
  • 783 Answers

SOURCE: Ford 460 Intake Manifold Torque spec

22 to 35 ft lbs

Posted on May 22, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: What is the torque spes

For 2004 Chevrolet Truck Silverado 2500HD 4WD 6.0L SFI 8cyl, the intake manifold, throttle body, fuel injection rail, and fuel injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly.

Intake manifold bolts. Tighten intake manifold bolts first pass in sequence to 44 inch lbs. (5 Nm). Tighten intake manifold bolts final pass in sequence to 89 inch lbs. (10 Nm).


zjlimited_865.jpg

Fig. Lower intake manifold bolt tightening sequence - 4.8L, 5.3L and 6.0L engines

Hope this helps.

Posted on Mar 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for upper intake manifold for an '07 Chrysler Pacifica 4.0


10mm nuts (6mm bolts) in aluminium usually require less than 7 ft/lbs (10Nm) of torque as its just a box bolted to a vacuum source. if you cant find torque specs, use internet charts for bolt sizes on something like this. Does not apply to head bolts as they are special

Aug 18, 2015 | Chrysler Cars & Trucks

1 Answer

The torque specs for upper intake manifold 2006 chrysler pacifica 3.5


Tighten bolts gradually starting in the center working outward until a torque of 12 Nm (105 inch lbs.) is obtained.

Mar 16, 2015 | Chrysler Cars & Trucks

1 Answer

Intake manifold bolt torque for 3.3 chrysler engine


Hi
Intake manifold to cylinder head tightening torque is 23 NM

Aug 17, 2014 | Cars & Trucks

1 Answer

Intake torque on top & bottom bolts


Apply sealer to the lower intake manifold bolts prior to installation. On the 5.0L and 5.7L engines, install the bolts and torque in sequence as follows:
Step 1: 71 inch lbs. (8 Nm).
Step 2: 106 inch lbs. (12 Nm).
Step 3: 11 ft. lbs. (15 Nm).


12_23_2011_2_54_59_am.gif

Fig. Lower intake manifold bolt tightening sequence-5.0L and 5.7L engines / zoom image link here

Upper intake manifold mounting bolts/studs, torque in a crisscross pattern as follows:
  1. Step 1: Torque the bolts/studs to 44 inch lbs. (5 Nm).
  2. Step 2: Torque the bolts/studs to 83 inch lbs. (10 Nm).

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day and Merry X-mas.

Dec 23, 2011 | 1999 Chevrolet Tahoe

1 Answer

I have a 1989 New Yorker with 3.0 L, wanted to know the torque settings for the intake manifold , body on top of intake along with the sequence order and the valve cover, thank you.


intake manifold torque is 174 inlb
valve cover is 88inlb end to end to center opposit of intake manifold .
hope this help.pls dont forget to like.

9278836-ggu5rsn2pvblwobn0lhlahdz-2-0.jpg

May 22, 2011 | Chrysler New Yorker Cars & Trucks

1 Answer

WHAT ARE THE TORQUE SPECS FOR THE INTAKE MANIFOLD BOLTS ON A 2001 CHRYSLER SEBRING 3.0L ENGINE


Sorry first attempt got sent by accident

Upper intake manifold bolts/nuts 168 in-lbs

Lower intake manifold nuts are done in 4 steps

Step1. Front nuts 61 in-lbs
Step2. Rear nuts 185 in-lbs
Step3. Front nuts 185 in-lbs
Step4. Repeat Steps 2 and 3

Feb 20, 2011 | 2001 Chrysler Sebring

1 Answer

2001 chrysler voyager just replaced head what are the torque specs for head intake and pivot arm


for the head

Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)

† Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)

† Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)

† Step 4: Bolts 1 - 8 turn an additional 1/4 Turn.

(Do not use a torque wrench for this step.)

NOTE: Bolt torque after 1/4 turn should be over 122
N·m (90 ft. lbs.). If not, replace the bolt.


Intake Manifold

Bolts . . . . . . . . . . . . . . . . . . . .23 N·m (200 in. lbs.)

Intake Manifold Gasket Retaining

Screws . . . . . . . . . . . . . . . . . .12 N·m (105 in. lbs.)

Intake Manifold Plenum
Bolts . . . . . . . . . . . . . . . . . . . .28 N·m (250 in. lbs.)
the pivot arm ? whats that

Nov 13, 2010 | 2001 Chrysler Voyager

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

Not finding what you are looking for?
2006 Chrysler 300 Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...