Question about Cars & Trucks

1 Answer

C6 transmission pan bolts where does longer bolt go?

Filter change didnt see where longer bolt came from

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Hi
more info required make model engine size 3,4,5,6, speed box

Does the bolt a flat end on it or sort of a pointy end, as this bolt may lock something inside the trans, if no machined end tag it an odd bolt fitted by someone in the past

Posted on Nov 26, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bryant329
  • 125 Answers

SOURCE: where is the transmission filter?

from what i can gather there is no filter replacement, only a fluid exchange. this info is coming from a rather good borderline great mech. program.

Posted on Sep 16, 2008

  • 57 Answers

SOURCE: Need to change the transmission filter in '99 chevy suburban 2wd.

If it has over 100,000 miles or so, don't do a complete fluid exchange. Drop the pan, change the filter, and add 2 bottles of Lucas trans. additive. No premises but it's better than a new trans. Worth a try.

Posted on May 22, 2009

outdoorsman5
  • 631 Answers

SOURCE: To Change 2004 Mitsubishi Endeavor Transmission filter

Yes you will need a gasket and if you go to the parts store they will sell you what you need. Just tell them what you have and they will give you the filter and gasket. I am not real sure on this year if there is a bolt holding the filter in place and I have looked in all my books on this one but can't seem to find out. If there is a bolt there will only be one more then likely but i really dont think you have a bolt. Just take the pan down and see if you can gently pull down the filter. Most of the time they are just up there with a O-Ring to hold them in.

Posted on Aug 05, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

  • 1810 Answers

SOURCE: Nissan Altima tring to change my transmission fulid and filter

thats why you have to remove the frame and for this you need an engine support and the average mechanic will charge you arround 100 bucks to do it
some rental stores have them some dont good luck eithor way you go but for god sake be carefull

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I have to bring down the transmission . In order to change the transmission filter?


No, the filter is beneath the bottom pan. You just have to remove the transmission pan and the filter is right there.
Loosen all the pan bolts, then remove the bolts from one end, letting the pan tilt down, draining the fluid -have an oil pan to catch it. When fluid has stopped draining, remove the pan and look for metal shavings. If not much there, replace the filter, new pan gasket and bolt the pan back up. Torque on the bolts is low, just snug them up, can always tighten further if leaking.

Sep 20, 2013 | Cars & Trucks

1 Answer

Change the transmission fluid


to change the transmission fluid and filter. jackup front of car, loosen all pan bolts. then loosen back bolts and take out the bolts, just to lower the pan to drain the fluid. when mostly all fluid has drained out. remove the other bolts and drop pan. to remove filter there are 2 screws. be careful not to lose the magnet in pan. remove filter and pry out the seal, push a new filter seal fully into its bore, then install new filter.working around pan, tighten the bolts a little at a time untill final torque is reached. fluid and filter change about 7 quarts. the pan bolts are 108 in-lbs. good-day !

Apr 08, 2012 | 1999 Chevrolet Malibu

2 Answers

Where is trans filter located


Hi,
The follwoing is from the GM Shop Technical Manual.
Changing the filter requires removing the transaxle oil pan and gasket,
Remove or disconnect

bendarden.jpg

  • Raise vehicle and suitably support.
  • Loosen oil pan bolts and drain fluid,
  • Remove oil pan attaching bolts.
  • Remove pan pan and gasket.
  • Remove the oiil filter using a long screwdriver pry filter neck out of the seal.
  • Check oil filter seal for damage or wear. If needed, remove and replace
Install or connect
  • install new oil filter and/or seal.
  • install the old pan gasket since it can be reused, unless sealing ribs are damaged. If damaged, use new gasket.
  • Install the oil pan and attaching bolts.
  • Tighten pan bolts to 13 lb. ft,
  • Lower vehicle.
  • Refill transxle to proper level with DEXRON III or DEXRON-IIE fluid.
  • Checkoil pan gasket for leaks,

May 21, 2011 | 1995 Buick LeSabre

1 Answer

How do I change transmition filter


Start the engine and let it idle for four minutes. This will help to remove as much loose particles from the transmission as possible Turn off the engine. Raise the front of the vehicle using a floor jack, and support the vehicle with two jack stands Apply the emergency brakes and block the rear wheels with two wooden blocks .Place a large drain pan underneath the transmission pan. Loosen the front and side mounting bolts from the transmission pan using a crisscross pattern. Then remove the bolts. Use a ratchet, ratchet extension and socket.Loosen the rear mounting bolts from the transmission pan about 4 turns each. Pry the transmission pan open at the front using a screwdriver and let the oil drain onto the drain pan. Hold the transmission pan from underneath, using a shop rag as you remove the remaining pan mounting bolts. Separate the transmission pan from the transmission, and tilt it over the drain pan to remove the remaining oil. Discard the transmission pan gasket. This is were the filter will be located remove and replace filter and then. Clean the transmission pan with spray carburetor cleaner and a shop rag.Install a new gasket over the transmission pan flange Set the transmission pan in place and start the pan mounting bolts by hand. Start tightening the transmission pan bolts in a crisscross pattern, a little at a time, until all the bolts are tight. Use the ratchet, ratchet extension and socket. Just tighten the bolts enough to create a seal between the pan and the transmission to avoid damaging the pan gasket.

Mar 18, 2011 | 2003 Chevrolet Impala

1 Answer

Gear selection is slow


Check your tranmission fluid level, if its low it can cause your transmission to shift slower, if its drastically low your transmission will slip in and out of gears or free rev (act like its in neutral) under acceleration or when shifting to a higher gear. If your fluid level is good, then you need to change your transmission filter. If your not mechanically inclined, take your vehicle to a shop and have them replace your filter for you, any repairs or maitnance envolving your transmission can easily go bad and potentially destroy your transmission if you do something wrong.

1. Buy new filter & transmission pan gasket

2. Raise vehicle, block tires, and use jackstands (never rely on any type of jack to hold the vehicle up.) and get a container or drain pan to catch the old transmission fluid.

3. Put drain pan or container under your transmission pan, start loosinging the bolts that hold the pan to the transmission. If you loosen the bolts alittle at a time you should be able to minimize spilling fluid everwhere and be able to catch it in your drain pan easier. (if your transmission has a drain plug remove it before loosening the pan bolts, this is not very common though and if you have a drain plug your lucky) once the majority of the fluid has drained from loosening the plugs, continue to loosen bolts so you drop the pan easily cause its gonna be full of fluid (unless you have the drain plug, if you do the pan should be virtually empty and you can remove it fully without alot of mess).

4. Locate the bolts that hold your filter to the transmission, be sure to only remove the bolts that hold the filter. Use the new filter for a visual aid so you can be 100% sure your only removing the filter. (The filter is bolted to a metal cover plate that houses the transmission clutch assemblies, spring valve assemblies, and floating shutter pins and they all operate under hydraulic pressure). Once the bolts are out of the old filter you should be able to slide the goose neck of the filter out of the filter port (again use the new filter for a visual aid) The goose neck should have a rubber o-ring type seal (or equivilent) make sure its on the old filter when you pull it, If its not then gently feel in the port and make sure the seal isnt sticking inside the port.


****** If you were to remove the cover plate thinking it was the filter, the hydraulic slide valves would move and you could seriously damage your transmission turning a $30.00 problem into a 1500.00 problem. I speak from experiance, so please use the new filter for a visual, I can't stress it enough*

5. Clean the pan's gasket area maticuliously, removing all of the old gasket, do the same to the transmission. Prep the pan side of your new gasket (I like using permatex gasket sealer) and install it to your transmission pad. (you can do this before you clean the transmission's gasket area so the permatex has time to adhear to the pan while you clean the gasket area on the transmission)

6. Using transmission fluid lube up the new filter's o-ring and slide it into the filter port. line up the bolt holes and start puting the filter bolts back in, tightening them evenly much like you would do to lug nuts if you had to change a tire.

7. Now get your pan and prep the other side of the pan gasket (gasket should be well tacky and sticking to the pan at this point) once the gasket is prep'd line the pan up with the transmission and begin installing the pan bolts tighten them the same way you did the filter bolts,

**Note**FWD** Depending on your vehicle's make/model, you may have to drop one of the control arms to remove the pan.

**Note**RWD** Depending on your vehicle's make/model, you may have to remove the cross member to remove the pan -or- drop the drive shaft, remove the bell housing bolts (bolts through transmission into engine block) remove the starter, and flywheel cover remove the bolts that connect your torq converter to your flywheel and slide the transmission back from the motor far enough so the transmission pan is no longer under the cross member.

GOOD LUCK I HOPE MY POST HELPS YOU!

Feb 03, 2011 | 1992 Toyota Previa

2 Answers

I need to change the transmission fluid, but I don't know how... I'm frustrated plz help...


simple task!!! jack up the car. get a pan BIGGER than the tranny pan itself. put pan below.while your doing this you might as well change the filter also!!!!!! start unbolting the pan, but leave a bolt at all 4 corners.once you have all but the 4, break them loose, but dont take them out.take two bolts out and let it drop down to get most of the tranny fluid out. once most of its out, take the other two bolts out and bam! there you go. if you have a new filter, it just pops out, make sure you take out the old seal.

Dec 06, 2010 | 2002 Lincoln LS

1 Answer

Need to change the transmission filter how and where is it located


Fluid & Filter Change Under normal service (moderate highway driving excluding excessive hot or cold conditions), the manufacturer feels that automatic transmission fluid should not need periodic changing. However, if a major service is performed to the transmission, if transmission fluid becomes burnt or discolored through severe usage or if the vehicle is subjected to constant stop-and-go driving in hot weather, trailer towing, long periods of highway use at high speeds, fluid should be changed to prevent transmission damage. A preventive maintenance change is therefore recommended for most vehicles at least every 90,000 miles (145,000 km).
Although not a required service, transmission fluid changing can help assure a trouble-free transmission. Likewise, changing the transmission filter at this time is also added insurance.
  1. Raise the car and support it securely on jackstands.
The torque converters on some transmissions are equipped with drain plugs. Because it may take some time to drain the fluid from the converter, you may wish to follow that procedure at this time, then come back to the pan and filter removal.

980822b.gif
Before removing the transmission fluid pan, insure that the area is clean of dirt and debris

2. Place a large drain pan under the transmission.

378093c.gif
Loosen all of the pan attaching bolts to within a few turns of complete removal


  1. Loosen all of the pan attaching bolts to within a few turns of complete removal, then carefully break the gasket seal allowing most of the fluid to drain over the edge of the pan.
CAUTION DO NOT force the pan while breaking the gasket seal. DO NOT allow the pan flange to become bent or otherwise damaged.

  1. When fluid has drained to the level of the pan flange, remove the pan bolts and carefully lower the pan doing your best to drain the rest of the fluid into the drain pan.ea833e6.gif


Once the pan is removed, discard the old gasket and insure that the mating surfaces are clean

9aa0aea.gif
Inspect this magnet inside of the pan for any large pieces of debris. A light gray coating is normal

11c6ddb.gif
Clean the pan thoroughly with a safe solvent and allow it to air dry

5. Clean the transmission oil pan thoroughly using a safe solvent, then allow it to air dry. DO NOT use a cloth to dry the pan which might leave behind bits of lint. Discard the old pan gasket.

22d9261.gif
The transmission filter is secured by a mounting bolt (arrow). Some models may use two bolts

097949a.gif
Remove the filter mounting bolt ...


d9f5189.gif
... then pull the filter free from the transmission

6. If necessary, remove the Automatic Transmission Fluid (ATF) filter mounting bolts, then remove the filter by pulling it down and off of the valve body. Make sure any gaskets or seals are removed with the old filter. The transmission usually has one round seal and a rectangular gasket.

7. Install the new oil filter screen making sure all gaskets or seals are in place, then secure using the retaining screws, if applicable.

50f9d74.gif
Install a new pan gasket


8. Place a new gasket on the fluid pan, then install the pan to the transmission. Tighten the attaching bolts to 71-119 inch lbs. (8-13 Nm).

34bd906.gif
Fill the transmission with the proper amount of ATF

9. Add three quarts (six quarts if the torque converter was drained) of fluid to the transmission through the filler tube.
10. Remove the jackstands and carefully lower the vehicle.
11. Start the engine and move the gear selector through all gears in the shift pattern. Allow the engine to reach normal operating temperature.
12. Check the transmission fluid level. Add fluid, as necessary, to obtain the correct level.

Nov 19, 2009 | 1997 Ford Explorer AWD

2 Answers

How do i service my transmission on a 2004 chevy trailblazer


transmission pan must be removed to drain fluid & change filter.loosen all pan bolts,remove all but 4 bolts @ corners.strike pan with a plastic hammer or block of wood if it's stuck. slowly remove remaining bolts,allowing fluid to drain into a suitable container.this can get messy,have rags handy.when drained,remove pan,clean pan & transmission gasket surfaces.pull filter straight down,push new filter on to tube,positioned as original,install new gasket,'run down 'all pan bolts then tighten them securely.

Oct 11, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

2 Answers

Flushing the transmission


To change the transmission fluid make sure you have purchased: 1. filter with the o-ring 2. MOPAR ATF + 3 Type 7176, p/n 05010124AA fluid (I believe it took 6 quarts?) You are not changing the torque converter fluid so there will not be 12 quarts needed.). 3. Pan gasket. You should receive the new neoprene reusable pan gasket. This is because the recommendation is to change the transmission fluid every 25,000 miles. 4. There is a fluid additive to prevent foaming? Use it.


Raise the vehicle on a hoist. Remove the pan bolts. Remove the old gasket material with a plastic scraper. There could be metal transfer if you use a metal scraper. Clean the pan carefully. Clean the magnet that sits in the pan as it collects the minute metal shavings. If you see an excess of larger particles, you really should have the transmission inspected at a shop. Replace the filter carefully looking at its arrangement before removing. It took a second look to install a new filter because I did not watch how it was situated before removing. Use a thin coat of transmission fluid on the new pan gasket. Orient reusable gasket properly with bolt holes and assemble oil pan and gasket to transmission case. Tighten oil pan bolts to 19 Nm (165 in lbs.). CAUTION: DO NOT OVERFILL TRANSAXLE. DO NOT ADD OIL IF LEVEL IS BETWEEN: LOWER HOLES FOR WARM OIL (100?F). UPPER HOLES FOR HOT OIL (180?F.).

Jun 12, 2008 | Chrysler Neon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...