Question about 2004 Chrysler Sebring Convertible

2 Answers

How do I fix the window switch for the front window on a 2004 chrysler Sebring Convertible

Nothing

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Chrysler Expert
  • 252 Answers

Do not try to pry it off the door panel, it will break it as it is welded ( plastic) to the door panel. remove the entire door panel for testing. many times the wiring between the body and drivers door will break inside the rubber boot from bending back and forth when the door opens and closes. many times i have seen this cause window related problems

Posted on Nov 28, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Are you sure it is the switch? test it ? pry it up and short it by passing a screwdriver (dont touch the metal with your hand) over the contacts. If it works than it is the switch, go to your Chrysler dealer or ebay or favorite parts place and purchase a new one... folow instructionsd for replacement.

Posted on Nov 26, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

hotrodshop
  • 106 Answers

SOURCE: Airbag light stays on in 2004 Chrysler Sebring

Sounds like you need to get it scanned for trouble codes. It will most likely need a new air bag clock spring. This is the wound connection under the steering wheel, it is a common failure item. It may be some other things related to the safty restraint system, but that will show up in a vehicle scan.

Posted on Jun 09, 2009

c17hydro
  • 2984 Answers

SOURCE: I need to replace an ignition switch on my 1999

This is for the ignition switch like you are asking for:

Ignition Switch REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disarm the air bag system, as described in Section 6.
  2. Remove the left end instrument panel cover/fuse panel and remove the retaining screw holding the end of the instrument panel top cover.
  3. Remove the instrument panel center bezel.
  4. Remove the screws that secure the instrument panel top cover to the center of the instrument panel.
  5. Lift the instrument panel top cover enough to gain access to the knee bolster attaching screws.
  6. Remove the lower knee bolster attaching screws and knee bolster from the vehicle.
  7. Remove the lower steering column cover attaching screws. Pull down on the lower cover to clear the ignition key cylinder and key release (if equipped).
  8. Remove the lower steering column cover, sliding the cover forward while holding down the steering wheel tilt lever.
  9. Tilt the steering wheel down to the fully lowered position and remove the upper steering column cover.
  10. Remove the screws that hold the combination switch to the ignition lock housing.
  11. Place the ignition lock cylinder in the RUN position.
  12. Insert a small prying tool into the hole in the lower cover and depress the cylinder release tab.
  13. Remove the ignition lock cylinder from the steering column.
  14. Unfasten the electrical connectors from the switch.
  15. Using a No. 10 Torx® bit, remove the ignition switch mounting screw.
  16. Depress the retaining tabs and remove the switch. To install:
  17. Place the ignition switch in the RUN position. Be sure the actuator shaft in the lock housing is also in the RUN position.
  18. Install the switch, making sure the switch snaps over the retaining tabs.
  19. Install the retaining screw.
  20. Connect the wiring to the ignition switch.
  21. Install the ignition lock cylinder.
  22. Install the 2 combination switch mounting screws.
  23. Install the lower and upper shrouds.
  24. Install the knee bolster to the lower dashboard panel and tighten the lower knee bolster attaching screws.
  25. Install the screws that secure the instrument panel top cover to the center of the instrument panel.
  26. Install the instrument panel center bezel.
  27. Install and tighten the screw holding the end of the instrument panel top cover. Install the left side instrument panel/fuse panel cover.
More coming.....

Posted on Jun 26, 2009

01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

sandman357
  • 236 Answers

SOURCE: 2004 chrysler sebring idle speed is too slow. HOw

why do you want your rpms higher while idling? you don't want them high because your gas bill will reflect that. slow shouldn't matter but if it's dying while on idle it could either be your mass air flow sensor or your fuel filter being clogged

Posted on Mar 23, 2010

jlisagearhea
  • 412 Answers

SOURCE: Where is the fuel filter located on a 2004 Chrysler Sebring Sedan

Some of the Sebrings have two filters(one is called a sock).The sock(which all sebrings have) is located in the fuel tank itself on the pump module.If this model is the JXI then the external filter is located on the belly of the car between the tank and drivers rear seat. I hope I could help!!!

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sebring horn


Do I need to remove the front number to get to the horn. Chrysler Sebring convertible. 2008

Jan 10, 2014 | 2004 Chrysler Sebring

1 Answer

When i open the top on my 1996 chrysler sebring convertible i notice that the front windows go down but the rear windows don't. is this normal or do they have a reset so they could go down a bit.


I had the same car,when we put the top down we had to hold the botton for the top in the down posistion until the back windows were down.

Nov 15, 2012 | Cars & Trucks

1 Answer

The power windows quit working


no not the same circuit check window fuse as well as drivers side switch this circuit also has a relay check for power going into as well as out of the drivers (left ) side duel switch this control powers the rt side switch also

Jul 07, 2012 | 2004 Chrysler Sebring

1 Answer

Passenger window wont roll up.......fuse/relay is good....window motor is good..module is good.......tested and got a ul 1110 and ul 1120 codes ...what is this ? 2008 sebring convertible / chrysler


IF THE PASSENGER WINDOW SWITCH IS BAD IT WONT WORK FROM EITHER SIDE HAS TO BE A COMPLETE CIRCUIT.IF YOU MANUALLY JUMPED WINDOW MOTOR WITH A BATTERY AND TWO WIRES ,I WOULD START THEIR.OR IF THE DRIVER WINDOW SWITCH IS BAD SAME THING

Aug 03, 2011 | 2008 Chrysler Sebring Convertible

2 Answers

Tire specs for 2001 chrysler sebring


HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16

Jul 06, 2010 | 2001 Chrysler Sebring

2 Answers

We have a 2004 chrysler sebring convertible yesterday the power window on the pasenger side stoped halfway up of course we can not find the owners manual is this a fuse problem or something that we need to...


IF THE DRIVERS SIDE WINDOW IS WORKING IT IS NOT A FUSE PROBLEM AS THESE ARE ON THE SAME CIRCUIT. MOST LIKELY IT WILL NEED A WINDOW MOTOR/REGULATOR ASSEMBLY WHICH IS BETTER HANDLED BY YOUR LOCAL TECH. HOPE THIS HELPS!

Sep 07, 2009 | 2004 Chrysler Sebring

2 Answers

Driving lights on chrysler sebring convertible


The roatating knob that turns on the headlight pulls out to turn on the fog lights, but only pulls out when the headlights are on,

Aug 15, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Convertible Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...