Question about 2007 Nissan Quest 3.5 Minivan

2 Answers

Need to remove the front bumper

I need to change the head light assembly because they're stained and don't give out good light.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Nissan Master
  • 552 Answers

Are they plastic lenses? if so get some insect repellent and spray it on the lense and wipe it clean

Posted on Nov 26, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,342 Answers

I have two older cars than yours and I just polish the lens with a gizmo that attaches to my cordless drill and plastic polisher. They come in kits at Walmart and other places.

Posted on Nov 26, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Change bulb in front headlamp

Yes you do have to remove the bumper, there are 2 screws underneath the assembly which the bumper obstructs. Once you get to this point it is pretty straight forward.

Posted on Jun 26, 2009

  • 5 Answers

SOURCE: how do you remove the front head light assembly in

There are two screws on the top of the light that you need to take off http://www.youtube.com/watch?v=GSj1en6ol-I

Posted on Jan 20, 2010

bonedivers
  • 1140 Answers

SOURCE: I would like to replace

Not normally.

Posted on Dec 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing a parking light bulb in front head light assembly


Remove the front wheel liner from the strut to the front bumper, all light assembly light bulbs will then be accessible. There may be screws however the majority is a plastic clip where you pull the center out then the clip easily removes.

Sep 08, 2013 | 2009 Buick Enclave

1 Answer

How to take passenger headlamp out of 328i bmw 2008 so it can be replaced?


2008 328i Passenger headlight assembly removal.

The headlight assembly is held in by 4 "star" bolts (size 25); 2 visible on the top of the assembly, 2 not visible or easily accessible.

The 2 bolts not so visible require that the front half of the wheel well come off and the front bumper or "nose" of the car.... The bumper is what needs to come off, but there are 2 bumper bolts hidden by the wheel well.

The wheel well is held in by 7mm bolts, 2 of which are actually bolted to the bumper on the bottom.

The front bumper is held on with 7mm bolts on the bottom edge, and star bolts, size 25, accessible on the top edge. (Hood open). Here were my steps.

1. Jack up the car on the side you are replacing, remove wheel.
2. Using 7mm socket, remove all the bolts to peel off the front half of the wheel well. With the wheel well out, you can see the 2 other star bolts holding the headlight assembly, but you can only remove one of them... even if you were good enough to get both removed, the headlight assemble will not push out through the bumper.... Keep going with bumper removal.
3. Remove 2, 7mm bolts of the front bumper that are now visible up near the outer edge of the headlight assembly.
4. At this point I removed the bumper's top edge start bolts and bottom edge 7mm bolts about 3/4 of the way across the bumper...
5. The bumper is very flexible and you can now pull it back , reach in, and get that last difficult star bolt on the headlight assembly....
6. Don't forget the one electrical connector....
7. I also recommend testing the new assembly by plugging it in before removing anything

Nov 09, 2012 | Cars & Trucks

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

2 Answers

How can I replace the left front fog light unit from a toyota prius from 2009. I cann't find a maintenance manual for this model and year.


Its all attached by clips and screws.Nothing much special.But its all about the procedure.Dont forget the mark the position , location of the screws you remove, so while refitting you don't face any problemTo replace fog light bulb or to replace replace complete fog light unit, click this link below:--- http://technoanswers.blogspot.com/2011/07/how-to-replace-left-front-fog-light.html ---------- This will help.Thanks.Helpmech.

Jul 09, 2011 | Toyota Prius Cars & Trucks

2 Answers

How to replace headlight on 2007 gmc acadia


first if you are changing the bulb only and it is a HALOGEN
there is a round acess hole in the inner fender remove it and change the bulb
if you have HID lights or are changing the head light assembly then you have to remove the front bumper facia
hope this helps
hope you have HALOGEN lights

Feb 11, 2010 | 2007 GMC Acadia SLE

1 Answer

How do I change my front turn signal? I can access the lower signal from under the bumper, I can't access the signal that is next to the headlight. There are no screws in front to take the plate off,...


The signal light on the grill next to the head light can be accessed by removing the the front grill. Your going to need a torque screw driver to remove the grill to get to the light bulb. The signal from under the bumper can be accessed from behind the bumper and you need not to take the turn light assemble off from the bumper. There are LED light bulbs available now and last much longer then the conventional bulbs and cost not that much more. Auto Zone carries these replacement LED bulbs and they can give you the step by step instruction to getting the job done if you need more illustration. Good luck and hope this helps and please rate, keep me posted. Be glad to help you get your lights replaced.

Jan 10, 2010 | 1991 GMC Sonoma

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

2 Answers

Where is the radiator fan relay switch located


the radiator fan relay is located under the passenger side head light,you will need to remove the grill and front bumper cover and of course the head light assembly,there are a few screws in the passenger side wheel well that need to come out also that hold the bumper cover on,most of the bolts holding the bumper on are torx ,hope this helps

Sep 08, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Need to replace head lamps on Ford Escape 2001,


there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose them...here is a cpoy of the manual to change..good luck

Headlamp Assembly Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Apr 22, 2009 | 2003 Ford Escape

2 Answers

How to change the whole headlight assembly on a 05 Honda CRV


You have to remove the front bumper and grill etc

There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.

Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.

Dec 23, 2008 | 2005 Honda CR-V

Not finding what you are looking for?
2007 Nissan Quest 3.5 Minivan Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...