Question about Cars & Trucks

1 Answer

How do i replace the front bumper for a chana benni

Take the top screws off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 623 Answers

Consult the factory repair manual. Check with the manufacturer.

Posted on Nov 29, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 27 Answers

SOURCE: Replace the face skid in the front bumper

remove front bumper and it should be clear what holding the face skid in place

Posted on Nov 07, 2008

  • 89 Answers

SOURCE: How do i adjust a chana benni's headlights

you have two srews one on top for up and down one on the side for side to side dont need much

Posted on Oct 28, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our chana benni 1.3 speedometer & odometer is not working,how do I fix the problem 2008 model


depends if its electric or cable driven.
2008 poss has a obd diagnostic port so i would find someone locally with a scanner who can test it out and verify fault area...eithe speed sensor or speedo head failure.

Jan 11, 2018 | Cars & Trucks

1 Answer

Can I replace my chana benni engine for another brand, will it require mods or gearbox replacement?


You need to use the same engine as a replacement or you will run into numerous very expensive problems.

Apr 11, 2016 | Cars & Trucks

1 Answer

My chana benni 1300 engin light is coming and flashes it misses and it sound like he is running in three silinders


Write your answer...my chana benni cuts out while I'm driving the I take the fuel cap off the it goes no problem what is wrong with my car

Mar 14, 2014 | Cars & Trucks

1 Answer

How do i adjust a chana benni's headlights


you have two srews one on top for up and down one on the side for side to side dont need much

Oct 28, 2013 | Cars & Trucks

1 Answer

How to replace nissan murano 2011 front driver side turn light


Lift hood, remove grill plastic screws on top, jack car left hand side, remove corner screw on end of bumper, undo lower splash shield screws, slide bumper away from car {about 4 inches}, remove,top bolts on headlight and lift out, the is a locating slot that you will need to manipulate it from, assembly is the reversal. good luck.

Oct 20, 2013 | 2007 Nissan Murano SE

1 Answer

Hyundai veracruz front bumper


Its fitted by screws and held by assembly.Give proper support to lower side and loosen the screws and bumper should easily come off.
---------------For complete step by step details,go through the help links mentioned below :-----

How to Attach the front bumper cover to the fender on 2010 Ford Explorer?

http://technoanswers.blogspot.com/2012/01/how-to-attach-front-bumper-cover-to.html
-----------

How to replace Bumpers on Acura Car models?
http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-bumpers-on-acura-car.html
-----------

How to Replace Front Bumper on Audi A4 and VW Passat?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-front-bumper-on-audi-a4.html
----------These will help.Thanks.

Nov 28, 2012 | 2008 Hyundai Veracruz

1 Answer

How do i replace the headlights


Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

Mar 29, 2010 | 2003 Jaguar S-Type

1 Answer

I would like to remove the front bumper of my 2003 Civic Hybrid. I want to replace the horn which is under the bumper.


pop hood .... remove clips directly on top of the bumper.... remove screws in fender.... and bolts under the bumper.... thats what i did on my civic yours should be similar.....

Jun 17, 2009 | Honda Civic Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14309 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...