Question about 1993 Geo Metro

1 Answer

1993 Geo metro 1ltr 3 cylinder engine need transmission bolt sizes

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 755 Answers

Most are like 10 mm nut size and 14 wrench size , try on till it fits , most are about 2 inches lone what happened to the old ones ,

Posted on Nov 25, 2014


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: transmission fluid for 94 geo metro

An automatic transmission on a 94 Geo Metro takes Dexron II (or higher- ie Dexron III etc) type transmission fluid only.

Posted on Jul 14, 2009

  • 258 Answers

SOURCE: I changed the thermostat on my 1993 geo metro and

check to see if the heater hoses are getting hot if one is hot and the other isn't the the heater core is stopped up if they are both hot you probably got a bad switch or something is up with the blend door check for vaccum leaks as well because i think the blend door opens and closes with vaccum

Posted on Nov 11, 2009

Testimonial: "Thank you very much for your answer. This helps alot."

  • 42 Answers

SOURCE: location of drain plug, fill plug and correct oil level plug for 5 speed manual transmission

I don't know if there is a fill plug. I just use the level plug located on driver's side right above the inner CV joint of the half-shaft (axle) to fill it. A piece of flexible tubing connected to a funnel works well. The drain plug is fairly near the center of the bottom of the gearbox housing (behind the bell housing). The level plug has a 24mm, fairly flat, hex head, and the drain plug is a recessed plug with a 3/8" (?) square hole (for a socket handle).

Posted on Apr 23, 2010

  • 1146 Answers

SOURCE: Automatic Transmission 97 metro

Specifically, you remove the transmission dipstick and use a narrow funnel to pour transmission fluid in the transmission till it is full. Remember to check your fluid level after the transmission is warmed up, and the car is running, gearshift in Park.

Posted on May 06, 2010

Testimonial: "Thanks!! I thought that might be it as I couldnt find a place to add, like the engine oil has..."

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1993 Geo Metro with a 3 cylinder 1 liter engine

wow ,6 posts, and even mixes 2 engines. all anon.
my guess. this is a 3 cylinder and is the Suzuki G10 , enigne
and has Throttle body injection.
what does "fluids out" mean?
leaks fuel someway, ? what fluid, name it. gas, oil, water,?

Sep 24, 2014 | 1993 Geo Metro

1 Answer

I have a 1993 Geo Metro and recently it has a MAJOR loss of power going up hill!

assuming its the engine? is it, and not transmission slipping? A/T?
1:the 60k tuneup in the operators guide done?
the 3 causes are. (takes tools to find which, in most cases.
lost compression , hot engine?
poor spark (weak or not timed right)
poor fueling.
there are simple tests for each.
we can do the tests, or guess?

Oct 27, 2013 | 1993 Geo Metro

1 Answer

I need torque for bolts in engine head

1.0L 3 cylinder

cylinder head bolts 54 ft lbs.

1.3L 4 cylinder

cylinder head bolts 54 ft lbs.

May 21, 2011 | 1995 Geo Metro

2 Answers

What is the cylinder head torque specs?

The torque for the cylinder head bolts is 54 Ft Lbs. or 73 Nm

Note: they should be torqued in three steps (i.e. 20 Ft Lbs, 40 Ft Lbs, then the final 54 Ft Lbs) in the sequence shown in the picture.dttech_28.gif

Feb 26, 2011 | 1993 Geo Metro

1 Answer

Can you take the motor for 1997 geo metro and put it in 1997 saturn sl2 ?

the metro is either a 3 or 4 cylinder japanese mitsubishi engine and has nothing in common with the 4 cylinder GM 1.9L 4. so you would have to manufacture new mounts, and electrical and mechanical connections for everything. assuming you have those skills, the car would be underpowered.
compare the size of the tiny metro with the small saturn. look in a junkyard for a 96-98 saturn engine which will bolt right in. note the donor vehicle must match the donee vehicle in engine a SOHC or DOHC.

Oct 19, 2010 | 1997 Saturn SC

1 Answer

1997 metro 3 cyl. misses on no.3

inspect the engine for arching from ignition wire to the engine ground on number three cylinder listen for a zapping sound . turn engine off and make sure the wire connections are solid then retry if it fixes the problem

Jun 22, 2009 | 1993 Geo Metro

1 Answer

1996 Geo Metro 4 cylinder

altanoter needs to be replaced

Dec 08, 2008 | 1993 Geo Metro

2 Answers

93 Geo Metro

As long as they are the same type of engine ( I believe they should both be 1.0L 3 cyl engines). Most parts for the Geo Metro from 1992 to 1994 interchange with out a problem.

Nov 10, 2008 | 1993 Geo Metro

2 Answers

Geo metro 1998 crankshaft pulley.

Remove motor and transmission mount bolts and using jack under motor/trans. assembly slide motor away from inner fender well to remove pulley.

Oct 31, 2008 | 1993 Geo Metro

Not finding what you are looking for?
1993 Geo Metro Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides